drilling TQ throttle plates? ***UPDATE***

Print Thread

Re: drilling TQ throttle plates? [Re: kilroy] #1256791 06/26/12 11:17 PM 06/26/12 11:17 PM
Joined: Jan 2003 Posts: 6,392 nielsville, minn. Q quickd100 master
quickd100 master Q Joined: Jan 2003 Posts: 6,392 nielsville, minn.	Not trying to start any arguements but I open up the low speed jet about .003 and adjust the initial timing to cure that problem. I've run cams at 274 to 292@.050 duration with thermoquads using these fixes. I DON'T drill the butterflys. Dave

Entire Thread
Subject	Posted By	Posted
drilling TQ throttle plates? *UPDATE*	kilroy	06/25/12 02:31 AM
Re: drilling TQ throttle plates?	Dan Halen	06/25/12 02:35 AM
Re: drilling TQ throttle plates?	kilroy	06/25/12 02:42 AM
Re: drilling TQ throttle plates?	DARTH V8Я	06/25/12 02:37 AM
Re: drilling TQ throttle plates?	kilroy	06/25/12 02:40 AM
Re: drilling TQ throttle plates?	RapidRobert	06/25/12 04:37 PM
Re: drilling TQ throttle plates?	Exit1965	06/25/12 02:42 AM
Re: drilling TQ throttle plates?	kilroy	06/25/12 02:44 AM
Re: drilling TQ throttle plates?	ahy	06/25/12 03:06 AM
Re: drilling TQ throttle plates?	DaytonaTurbo	06/25/12 04:35 AM
Re: drilling TQ throttle plates?	kilroy	06/25/12 04:52 AM
Re: drilling TQ throttle plates?	DaytonaTurbo	06/25/12 06:02 AM
Re: drilling TQ throttle plates?	superbeedave	06/25/12 04:10 PM
Re: drilling TQ throttle plates?	MY340	06/25/12 04:37 PM
Re: drilling TQ throttle plates?	kilroy	06/26/12 12:16 AM
Re: drilling TQ throttle plates?	Diplomat360	06/25/12 05:49 PM
Re: drilling TQ throttle plates?	kilroy	06/26/12 12:26 AM
Re: drilling TQ throttle plates?	Diplomat360	06/26/12 04:16 AM
Re: drilling TQ throttle plates?	kilroy	06/26/12 05:20 AM
Re: drilling TQ throttle plates?	Dave Watt	06/26/12 04:58 PM
Re: drilling TQ throttle plates?	kilroy	06/27/12 01:13 AM
Re: drilling TQ throttle plates?	Diplomat360	06/26/12 05:49 PM
Re: drilling TQ throttle plates?	Rapid340	06/26/12 06:24 PM
Re: drilling TQ throttle plates?	kilroy	06/27/12 01:17 AM
Re: drilling TQ throttle plates?	kilroy	06/27/12 01:22 AM
Re: drilling TQ throttle plates?	quickd100	06/27/12 03:17 AM
Re: drilling TQ throttle plates?	kilroy	06/27/12 03:43 AM
Re: drilling TQ throttle plates?	DARTH V8Я	06/27/12 03:52 AM
Re: drilling TQ throttle plates?	kilroy	06/27/12 11:48 PM
Re: drilling TQ throttle plates? *UPDATE*	kilroy	07/02/12 12:30 AM
Re: drilling TQ throttle plates?	Rug_Trucker	07/02/12 01:53 AM
Re: drilling TQ throttle plates?	kilroy	07/02/12 01:56 AM
Re: drilling TQ throttle plates?	kilroy	07/02/12 03:24 AM
Re: drilling TQ throttle plates?	440newport	07/02/12 03:50 PM
Re: drilling TQ throttle plates?	kilroy	08/02/12 03:59 AM

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To