Re: 6 Pak Throttle Rods
[Re: 70sixpkrt]
#3085549
10/12/22 06:04 PM
10/12/22 06:04 PM
|
Joined: Jan 2006
Posts: 2,377 White Plains, NY
VCODE
top fuel
|
top fuel
Joined: Jan 2006
Posts: 2,377
White Plains, NY
|
Are you using the carb H bolt 1-1/4 inch long. I took off carbs off a 340 -6 and someone cut them. Does not seem like the intake manifold treads a deep enough for the bolts without cutting them. Thanks Bob
Mom & Dad let me buy a brand new 70 Challenger R/T 440 Six-Pack Super Trac Pack when I was 17
(Robert what is a 440 Six-Pack)
|
|
|
Re: 6 Pak Throttle Rods
[Re: VCODE]
#3085561
10/12/22 07:20 PM
10/12/22 07:20 PM
|
Joined: Jan 2003
Posts: 3,682 South San Francisco, Ca
70sixpkrt
master
|
master
Joined: Jan 2003
Posts: 3,682
South San Francisco, Ca
|
Are you using the carb H bolt 1-1/4 inch long. I took off carbs off a 340 -6 and someone cut them. Does not seem like the intake manifold treads a deep enough for the bolts without cutting them. Thanks Bob This picture is not my engine. I am running some stock bolts.
|
|
|
Re: 6 Pak Throttle Rods
[Re: VCODE]
#3085672
10/13/22 06:16 AM
10/13/22 06:16 AM
|
Joined: Jan 2003
Posts: 6,391 Abilene, Texas
fastmark
master
|
master
Joined: Jan 2003
Posts: 6,391
Abilene, Texas
|
Are you using the carb H bolt 1-1/4 inch long. I took off carbs off a 340 -6 and someone cut them. Does not seem like the intake manifold treads a deep enough for the bolts without cutting them. Thanks Bob They make two different lengths of H bolts. The 1.250 are for four barrels with the thick base gasket. Six pack used the 1.00” ones. That intake and carbs is nicely detailed but the center pivot is not the correct oem one. That is an aftermarket piece. The oem used a pin with a clip instead of a bolt. Several companies sell the correct one. I think shakerhood.com does.
|
|
|
Re: 6 Pak Throttle Rods
[Re: fastmark]
#3085679
10/13/22 07:40 AM
10/13/22 07:40 AM
|
Joined: Jan 2006
Posts: 2,377 White Plains, NY
VCODE
top fuel
|
top fuel
Joined: Jan 2006
Posts: 2,377
White Plains, NY
|
Are you using the carb H bolt 1-1/4 inch long. I took off carbs off a 340 -6 and someone cut them. Does not seem like the intake manifold treads a deep enough for the bolts without cutting them. Thanks Bob They make two different lengths of H bolts. The 1.250 are for four barrels with the thick base gasket. Six pack used the 1.00” ones. That intake and carbs is nicely detailed but the center pivot is not the correct oem one. That is an aftermarket piece. The oem used a pin with a clip instead of a bolt. Several companies sell the correct one. I think shakerhood.com does. Who sells the 1.00 inch ones. Thanks Bob
Mom & Dad let me buy a brand new 70 Challenger R/T 440 Six-Pack Super Trac Pack when I was 17
(Robert what is a 440 Six-Pack)
|
|
|
Re: 6 Pak Throttle Rods
[Re: VCODE]
#3086061
10/14/22 05:29 PM
10/14/22 05:29 PM
|
Joined: Jul 2011
Posts: 956 Chicago
PurpleBeeper
super stock
|
super stock
Joined: Jul 2011
Posts: 956
Chicago
|
just a tip.....the back mechanical return rod is VERY close to the intake and if installed backwards, it can just barely hang up against the intake when you are at wide-open-throttle & make the carburetors stick wide open (ask me how I know)
70 Roadrunner convt. street car
440+6, NOS, 4-spd, SS springs
'96 Mustang GT convt. street car
'04 4.6 SOHC, NOS, auto, lowered
"Officer, that button is for short on-ramps"
|
|
|
Re: 6 Pak Throttle Rods
[Re: PurpleBeeper]
#3087115
10/18/22 10:54 AM
10/18/22 10:54 AM
|
Joined: Aug 2009
Posts: 1,317 Ohio
jlatessa
pro stock
|
pro stock
Joined: Aug 2009
Posts: 1,317
Ohio
|
Exactly what happened to me in 1970 with my A12. Showing off with a buddy in the car on an on-ramp, it hung up!!!
While I was busy stamping on the pedal and avoiding cars, my friend had the presence of mind to turn the key off. My hair still stands up thinking about that one.
Joe
Last edited by jlatessa; 10/18/22 10:55 AM.
|
|
|
Re: 6 Pak Throttle Rods
[Re: VCODE]
#3087150
10/18/22 01:01 PM
10/18/22 01:01 PM
|
Joined: Jan 2003
Posts: 6,391 Abilene, Texas
fastmark
master
|
master
Joined: Jan 2003
Posts: 6,391
Abilene, Texas
|
Are you using the carb H bolt 1-1/4 inch long. I took off carbs off a 340 -6 and someone cut them. Does not seem like the intake manifold treads a deep enough for the bolts without cutting them. Thanks Bob They make two different lengths of H bolts. The 1.250 are for four barrels with the thick base gasket. Six pack used the 1.00” ones. That intake and carbs is nicely detailed but the center pivot is not the correct oem one. That is an aftermarket piece. The oem used a pin with a clip instead of a bolt. Several companies sell the correct one. I think shakerhood.com does. Who sells the 1.00 inch ones. Thanks Bob AMK fasteners
|
|
|
Re: 6 Pak Throttle Rods
[Re: fastmark]
#3087401
10/19/22 08:33 AM
10/19/22 08:33 AM
|
Joined: Jan 2006
Posts: 2,377 White Plains, NY
VCODE
top fuel
|
top fuel
Joined: Jan 2006
Posts: 2,377
White Plains, NY
|
AMK has them listed a 1-1/8 long. Thanks Bob
Last edited by VCODE; 10/19/22 08:50 AM.
Mom & Dad let me buy a brand new 70 Challenger R/T 440 Six-Pack Super Trac Pack when I was 17
(Robert what is a 440 Six-Pack)
|
|
|
Re: 6 Pak Throttle Rods
[Re: VCODE]
#3087425
10/19/22 10:12 AM
10/19/22 10:12 AM
|
Joined: Jan 2003
Posts: 6,391 Abilene, Texas
fastmark
master
|
master
Joined: Jan 2003
Posts: 6,391
Abilene, Texas
|
AMK has them listed a 1-1/8 long. Thanks Bob I’ll check originals vs the two sizes I just bought from them. They probably are 1-1/8” long. The longer ones are for the thick Carter gaskets on the four barrel.
|
|
|
|
|