Small block oil pan question
#1982262
01/02/16 09:39 PM
01/02/16 09:39 PM
|
Joined: Aug 2003
Posts: 1,123 Seaford Delaware
JSR1485
OP
super stock
|
OP
super stock
Joined: Aug 2003
Posts: 1,123
Seaford Delaware
|
What is better to use in a Bracket car ? Kevko M301 pan? I have old Super Stock style pan with the tie rod tube or should I get a Stefs or Charlie's pan? or Milodon?
What do you guys use?
Switched to the dark side...
|
|
|
Re: Small block oil pan question
[Re: DavidDean]
#1982283
01/02/16 10:11 PM
01/02/16 10:11 PM
|
Joined: Oct 2009
Posts: 1,267 North, Alabama
D-50
pro stock
|
pro stock
Joined: Oct 2009
Posts: 1,267
North, Alabama
|
I am using the Kevco M301 pan. It is a 6 qt. I shift at 6800 and use a stock oil pump.
1.33 60 ft,6.21 at 110.59 in the 1/8, pump gas small block,2950lbs,drag radials,mufflers and driven to track ...
|
|
|
Re: Small block oil pan question
[Re: JSR1485]
#1983566
01/04/16 05:46 PM
01/04/16 05:46 PM
|
Joined: Aug 2003
Posts: 1,123 Seaford Delaware
JSR1485
OP
super stock
|
OP
super stock
Joined: Aug 2003
Posts: 1,123
Seaford Delaware
|
I have no problem with the Kevko pan and header clearance , Myron your right about the SS pan it is a P I N A to pull the engine with it. The only reason I was thinking of the SS pan was the pickup for it runs straight down and the pickup area is boxed in with some trap doors
Switched to the dark side...
|
|
|
Re: Small block oil pan question
[Re: JSR1485]
#1983706
01/04/16 08:49 PM
01/04/16 08:49 PM
|
Joined: Aug 2003
Posts: 4,988 new jersey usa
11secdart
master
|
master
Joined: Aug 2003
Posts: 4,988
new jersey usa
|
I had a Milodon that the center link went thru, looked cool but was a pia when pulling the motor. Milodon makes another one but the way it kicks out on both sides would be a problem for my Tubular Automotive headers as they are close to the oil pan. I 've had the Moroso 8 qt. on my past three motors as well as my new 408.
Last edited by 11secdart; 01/04/16 08:50 PM.
68 Dart 410 / 904 92 D150 original owner 21 Ram 1500 Quad Cab, Big Horn , Hemi ,4x4 23 Audi Q5 16 Honda HRV
|
|
|
Re: Small block oil pan question
[Re: 11secdart]
#1983819
01/04/16 11:16 PM
01/04/16 11:16 PM
|
Joined: Nov 2004
Posts: 3,517 pacific northwest
Stroker Scamp
master
|
master
Joined: Nov 2004
Posts: 3,517
pacific northwest
|
Moroso here, TTI headers,stock steering
footbrake N/A SB 408 Scamp 10.10 @ 132 street/strip 73 Duster 340 street strip 12.79 @ 105
|
|
|
Re: Small block oil pan question
[Re: JSR1485]
#1985941
01/07/16 11:39 PM
01/07/16 11:39 PM
|
Joined: Oct 2003
Posts: 7,506 Az
Crizila
master
|
master
Joined: Oct 2003
Posts: 7,506
Az
|
What is better to use in a Bracket car ? Kevko M301 pan? I have old Super Stock style pan with the tie rod tube or should I get a Stefs or Charlie's pan? or Milodon?
What do you guys use? I run an 8 qt Milodon in my late B. Had to make a slight mod to the K member. Headers fit fine.
Fastest 300
|
|
|
Re: Small block oil pan question
[Re: Crizila]
#1986593
01/08/16 11:26 PM
01/08/16 11:26 PM
|
Joined: May 2007
Posts: 1,675 Mi.
G-Money1320
top fuel
|
top fuel
Joined: May 2007
Posts: 1,675
Mi.
|
I run the Milodon 8 qt. in my 69 Dart with TTI headers and all stock suspension, all good but as Myron said the stock K frame needs a notch on the right side.
416 stroker from Nick at Compu-flow. 11.14 in full street trim. Seems like a new best every time out. 11.06 open headers----so far!!
|
|
|
Re: Small block oil pan question
[Re: JSR1485]
#1986711
01/09/16 02:12 AM
01/09/16 02:12 AM
|
Joined: Jan 2003
Posts: 8,028 Tulsa OK
Bad340fish
master
|
master
Joined: Jan 2003
Posts: 8,028
Tulsa OK
|
Same here with the Milodon and TTI headers, no complaints.
68 Barracuda Formula S 340
|
|
|
|
|