Re: New 4" Crank Dome Piston Offering from Wiseco Pistons
[Re: Dartwizer]
#923998
02/14/11 08:49 PM
02/14/11 08:49 PM
|
Joined: Jan 2007
Posts: 526 NC
barracuda man
mopar
|
mopar
Joined: Jan 2007
Posts: 526
NC
|
Quote:
When are they going into production?
x2 RyanJ on the 416cu at 14:1 compression.What head gaskit is used.
|
|
|
Re: New 4" Crank Dome Piston Offering from Wiseco Pistons
[Re: barracuda man]
#923999
02/14/11 08:55 PM
02/14/11 08:55 PM
|
Joined: Jan 2003
Posts: 8,547 State College, PA
RyanJ
OP
moparts member
|
OP
moparts member
Joined: Jan 2003
Posts: 8,547
State College, PA
|
Quote:
Quote:
When are they going into production?
x2 RyanJ on the 416cu at 14:1 compression.What head gaskit is used.
Cometic is all I use above 11:1
They are waiting for new batch of Forgings, but if you "need" a set ASAP, they are willing to do run of Customs in this spec for same cost until they get caught back up on forgings. The new forgings are supposed to be few weeks out & will have a .250" exhaust pocket for increased piston to valve with the bigger cams.
|
|
|
Re: New 4" Crank Dome Piston Offering from Wiseco Pistons
[Re: RyanJ]
#924000
02/14/11 09:13 PM
02/14/11 09:13 PM
|
Joined: Jan 2007
Posts: 526 NC
barracuda man
mopar
|
mopar
Joined: Jan 2007
Posts: 526
NC
|
Quote:
Quote:
Quote:
When are they going into production?
x2 RyanJ on the 416cu at 14:1 compression.What head gaskit is used.
Cometic is all I use above 11:1
They are waiting for new batch of Forgings, but if you "need" a set ASAP, they are willing to do run of Customs in this spec for same cost until they get caught back up on forgings. The new forgings are supposed to be few weeks out & will have a .250" exhaust pocket for increased piston to valve with the bigger cams.
Will they be a package deal with pins and rings.
|
|
|
Re: New 4" Crank Dome Piston Offering from Wiseco Pistons
[Re: RyanJ]
#924001
02/14/11 09:26 PM
02/14/11 09:26 PM
|
Joined: Jan 2007
Posts: 526 NC
barracuda man
mopar
|
mopar
Joined: Jan 2007
Posts: 526
NC
|
Quote:
Quote:
Quote:
When are they going into production?
x2 RyanJ on the 416cu at 14:1 compression.What head gaskit is used.
Cometic is all I use above 11:1
They are waiting for new batch of Forgings, but if you "need" a set ASAP, they are willing to do run of Customs in this spec for same cost until they get caught back up on forgings. The new forgings are supposed to be few weeks out & will have a .250" exhaust pocket for increased piston to valve with the bigger cams.
I'm looking for 11:5 to 12:1 compression on the 418cu.I have 65"cometic gaskits.what compression will i have with a 65cc eldlebrock 340 heads.
|
|
|
Re: New 4" Crank Dome Piston Offering from Wiseco Pistons
[Re: Discoquik]
#924005
03/15/11 11:04 PM
03/15/11 11:04 PM
|
Joined: Jan 2007
Posts: 526 NC
barracuda man
mopar
|
mopar
Joined: Jan 2007
Posts: 526
NC
|
Quote:
Due date for all oversizes is 3/18/11 for finished parts in all oversizes. We did some internal milling to take some weight out with added dome rise that is needed to compensate for the deeper valve pocket. Wound up a little lighter than the samples sent to Ryan, Indy, Muscle Motors, Bob G, Koffel, Hughes, and Compuflow.
Should be able to order through any distributor with K0011B3/4/6/8 or 100 oversize part numbers and includes piston, rings, and clips.
.927" pin versions do not have a part number as of yet, but in process.
As a side note 318 flat top and dish parts are on the way for 4.00" stroker combos in the Pro Tru line.
Any update on the pistons.
|
|
|
Re: New 4" Crank Dome Piston Offering from Wiseco Pistons
[Re: barracuda man]
#924006
03/15/11 11:24 PM
03/15/11 11:24 PM
|
Joined: Nov 2004
Posts: 3,544 Syracuse,NY
CompWedgeEngines
master
|
master
Joined: Nov 2004
Posts: 3,544
Syracuse,NY
|
RIP Monte Smith
Your work is a reflection of yourself, autograph it with quality.
WD for Diamond Pistons,Sidewinder cylinder heads, Wiseco, K1 rods and cranks,BAM lifters, Morel lifters, Molnar Technologies, Harland Sharp, Pro Gear, Cometic, King Engine Bearings and many others.
|
|
|
Re: New 4" Crank Dome Piston Offering from Wiseco Pistons
[Re: meus31]
#924009
05/02/11 04:53 PM
05/02/11 04:53 PM
|
Joined: Nov 2004
Posts: 3,544 Syracuse,NY
CompWedgeEngines
master
|
master
Joined: Nov 2004
Posts: 3,544
Syracuse,NY
|
Brett,
I have a sample you can look at. I will try to call you later tonight.
Todd
RIP Monte Smith
Your work is a reflection of yourself, autograph it with quality.
WD for Diamond Pistons,Sidewinder cylinder heads, Wiseco, K1 rods and cranks,BAM lifters, Morel lifters, Molnar Technologies, Harland Sharp, Pro Gear, Cometic, King Engine Bearings and many others.
|
|
|
|
|