ar engineering
#2910005
04/14/21 09:17 AM
04/14/21 09:17 AM
|
Joined: Jan 2003
Posts: 1,622 westerly, ri. usa
440lebaron
OP
top fuel
|
OP
top fuel
Joined: Jan 2003
Posts: 1,622
westerly, ri. usa
|
looking for alternator pulley and part # single groove denso 90 amp, website contact only shows address thanks gary
all parts are sold as is, all parts are considered used no warranties or returns paypal/check/money order, shipping is from zip 02891, buyer pays paypal fees 24% IRS 1099A plus 3% of part price, check/money order preferred site is not monitored 24/7 there might be a delay in response
|
|
|
Re: ar engineering
[Re: Cuda340]
#2910018
04/14/21 09:55 AM
04/14/21 09:55 AM
|
Joined: Mar 2006
Posts: 1,229 In The Hills
jughed
pro stock
|
pro stock
Joined: Mar 2006
Posts: 1,229
In The Hills
|
Hopefully OP can get through. I PMed him some tech questions about his alternator mounting bracket 6 days ago but have not gotten a response. I'm sure he's busy at this time of year.
|
|
|
Re: ar engineering
[Re: jughed]
#2910038
04/14/21 11:28 AM
04/14/21 11:28 AM
|
Joined: Jan 2003
Posts: 5,997 Anoka County, MN
Leigh
master
|
master
Joined: Jan 2003
Posts: 5,997
Anoka County, MN
|
Can't help you with AR, but you can go to Doty for pulleys. Some may show "out of stock" but there are different colors available that are in stock. They also make very nice brackets to mount the Denso (or GM) alternator. Just ordered the bracket and a pulley. https://www.dotymi.com/17-billet-aluminum-crankshaft-pulleys I know the OP was for Andy. Just a shout out to him and Doty Mfg, for good products.
|
|
|
Re: ar engineering
[Re: 440lebaron]
#2910067
04/14/21 12:48 PM
04/14/21 12:48 PM
|
Joined: Jan 2003
Posts: 31,200 Oregon
AndyF
I Win
|
I Win
Joined: Jan 2003
Posts: 31,200
Oregon
|
looking for alternator pulley and part # single groove denso 90 amp, website contact only shows address thanks gary That isn't a question for me since I don't make those parts. My website has a bunch of information on it about my parts but I can't answer questions on other people's parts. If you have a tech question post it on this board. If I know the answer and I see the question I might pop in and answer it but don't send questions to me directly. I don't have enough time in the day to answer everyone's questions.
Last edited by AndyF; 04/14/21 12:51 PM.
|
|
|
Re: ar engineering
[Re: AndyF]
#2910073
04/14/21 01:19 PM
04/14/21 01:19 PM
|
Joined: Jan 2003
Posts: 1,622 westerly, ri. usa
440lebaron
OP
top fuel
|
OP
top fuel
Joined: Jan 2003
Posts: 1,622
westerly, ri. usa
|
all I want to do is buy a pulley
all parts are sold as is, all parts are considered used no warranties or returns paypal/check/money order, shipping is from zip 02891, buyer pays paypal fees 24% IRS 1099A plus 3% of part price, check/money order preferred site is not monitored 24/7 there might be a delay in response
|
|
|
Re: ar engineering
[Re: 440lebaron]
#2910085
04/14/21 01:44 PM
04/14/21 01:44 PM
|
Joined: Jan 2003
Posts: 31,200 Oregon
AndyF
I Win
|
I Win
Joined: Jan 2003
Posts: 31,200
Oregon
|
all I want to do is buy a pulley I don't sell pulleys so you'll need to contact someone who sells pulleys. Measure the shaft size on your alternator and search for pulleys at Summit or Powermaster.
Last edited by AndyF; 04/14/21 01:48 PM.
|
|
|
Re: ar engineering
[Re: Stanton]
#2910321
04/14/21 11:48 PM
04/14/21 11:48 PM
|
Joined: Sep 2006
Posts: 3,017 Sac, CA
mopowers
master
|
master
Joined: Sep 2006
Posts: 3,017
Sac, CA
|
I just went through this myself. I ended up going full redneck, chucked up the factory 2-groove pulley in my drill press, and cut the outer groove off with a cutoff wheel on an angle grinder (I have no access to a lathe). It worked out perfectly, but shortly after, I found out Powermaster sells single groove pulley's for the Denso 17 mm shaft - #181, #182, and #183, depending on what OD you're looking for.
Keep in mind that a Bosch 17mm ID pulley may not work because the Denso alternators are 'domed' in the front, so the pulley needs to be dished on the back side for clearance.
Last edited by mopowers; 04/14/21 11:49 PM.
|
|
|
Re: ar engineering
[Re: AndyF]
#2910382
04/15/21 06:20 AM
04/15/21 06:20 AM
|
Joined: Jan 2003
Posts: 5,765 Hot Rod Ridge
FastmOp
master
|
master
Joined: Jan 2003
Posts: 5,765
Hot Rod Ridge
|
Ouch, a drill press and an angle grinder combo makes me wince. You're one small slip away from a major industrial accident when you do stuff like that. I have a buddy with a lathe so I just dropped the pulley off with a couple of $20 bills and let him deal with it. Dang Alice! You would hate to see me hack sh!t up.
|
|
|
|
|