Re: TH400 to RB in 69 b body info
[Re: AndyF]
#2774516
05/14/20 01:51 PM
05/14/20 01:51 PM
|
Joined: Aug 2003
Posts: 4,676 On the parachute mount
n20mstr
master
|
master
Joined: Aug 2003
Posts: 4,676
On the parachute mount
|
Check the depth going into the adapter with the converter, mine only had .030 . I took .100 off The adapter so the converter had more clearance . I checked it with some play-do
Last edited by n20mstr; 05/14/20 01:52 PM.
....BAD A$$ STREET CAR.....
|
|
|
Re: TH400 to RB in 69 b body info
[Re: n20mstr]
#2774561
05/14/20 03:40 PM
05/14/20 03:40 PM
|
Joined: May 2011
Posts: 4,489 northern,Ohio,USA
Clanton
OP
master
|
OP
master
Joined: May 2011
Posts: 4,489
northern,Ohio,USA
|
I will talk to you about this later today.I have no base measurements to go by. Check the depth going into the adapter with the converter, mine only had .030 . I took .100 off The adapter so the converter had more clearance . I checked it with some play-do
|
|
|
Re: TH400 to RB in 69 b body info
[Re: Cab_Burge]
#2774732
05/15/20 08:25 AM
05/15/20 08:25 AM
|
Joined: May 2011
Posts: 4,489 northern,Ohio,USA
Clanton
OP
master
|
OP
master
Joined: May 2011
Posts: 4,489
northern,Ohio,USA
|
I think the biggest offset I can get is .015 and to pull the 1's in the engine all I have is some visegrips so I hope that works.Moving the bell .015"I don't think is going to effect the starter much.
Last edited by Clanton; 05/15/20 09:12 AM.
|
|
|
Re: TH400 to RB in 69 b body info
[Re: DoubleD]
#2774788
05/15/20 11:18 AM
05/15/20 11:18 AM
|
Joined: May 2011
Posts: 4,489 northern,Ohio,USA
Clanton
OP
master
|
OP
master
Joined: May 2011
Posts: 4,489
northern,Ohio,USA
|
I didn't.I measured for the low spot and 0 the dial.I still have it set in place to measure today but I am confident it is reading okay in the small steps I am turning it and the angle is small. .032 off center? - I think you better double check your measurements again - I have never seen one out that far
How are you centering your dial indicator on the Crank??
Last edited by Clanton; 05/15/20 11:21 AM.
|
|
|
Re: TH400 to RB in 69 b body info
[Re: DoubleD]
#2774790
05/15/20 11:19 AM
05/15/20 11:19 AM
|
Joined: Sep 2003
Posts: 2,175 Duloc
The Shadow
top fuel
|
top fuel
Joined: Sep 2003
Posts: 2,175
Duloc
|
.032 off center? - I think you better double check your measurements again - I have never seen one out that far
How are you centering your dial indicator on the Crank?? Doesn't need centering on the crank
|
|
|
Re: TH400 to RB in 69 b body info
[Re: n20mstr]
#2774795
05/15/20 11:29 AM
05/15/20 11:29 AM
|
Joined: May 2011
Posts: 4,489 northern,Ohio,USA
Clanton
OP
master
|
OP
master
Joined: May 2011
Posts: 4,489
northern,Ohio,USA
|
When I get that far and have the converter I will lay it against the flex plate and check it.Thank youThe I.D. was 1.704 Check the depth going into the adapter with the converter, mine only had .030 . I took .100 off The adapter so the converter had more clearance . I checked it with some play-do
|
|
|
Re: TH400 to RB in 69 b body info
[Re: Clanton]
#2774948
05/15/20 07:17 PM
05/15/20 07:17 PM
|
Joined: Dec 2004
Posts: 10,553 Rittman Ohio
fourgearsavoy
I Live Here
|
I Live Here
Joined: Dec 2004
Posts: 10,553
Rittman Ohio
|
Hey Mike if you need a rock solid dial indicator mount that bolts to the crank flange you can use mine. I had it made strong so I could get my bell dialed in without the indicator moving around. Let me know and I can meet you somewhere and get it to you. Gus
64 Plymouth Savoy 493 Indy EZ's by Nick at Compu-Flow 5-Speed Richmond faceplate Liberty box Dana 60
|
|
|
Re: TH400 to RB in 69 b body info
[Re: fourgearsavoy]
#2774967
05/15/20 08:20 PM
05/15/20 08:20 PM
|
Joined: May 2011
Posts: 4,489 northern,Ohio,USA
Clanton
OP
master
|
OP
master
Joined: May 2011
Posts: 4,489
northern,Ohio,USA
|
What a great offer Thank you.I think I am within .003 soI have had enough for now and will move on to getting a converter,driveshaft n yokeThe solid mount sounds interesting if you have a pic? Hey Mike if you need a rock solid dial indicator mount that bolts to the crank flange you can use mine. I had it made strong so I could get my bell dialed in without the indicator moving around. Let me know and I can meet you somewhere and get it to you. Gus
|
|
|
|
|