Cutting cast iron

Print Thread

Cutting cast iron #2822651 09/19/20 03:53 PM 09/19/20 03:53 PM
Joined: Jan 2004 Posts: 8,368 fredericksburg,va C cudaman1969 OP master
cudaman1969 OP master C Joined: Jan 2004 Posts: 8,368 fredericksburg,va	I need a section off of a broken block, can I cut with an oxy-acetaline torch? I would cut a much larger section then grind it down to fit. Can’t get to it with a grinder or saw Last edited by cudaman1969; 09/19/20 03:54 PM.

Entire Thread
Subject	Posted By	Posted
Cutting cast iron	cudaman1969	09/19/20 07:53 PM
Re: Cutting cast iron	6PakBee	09/19/20 08:32 PM
Re: Cutting cast iron	cudaman1969	09/19/20 09:10 PM
Re: Cutting cast iron	elmor353	09/19/20 09:11 PM
Re: Cutting cast iron	TJP	09/19/20 11:19 PM
Re: Cutting cast iron	67vertman	09/19/20 11:59 PM
Re: Cutting cast iron	cudaman1969	09/20/20 12:48 AM
Re: Cutting cast iron	6PakBee	09/20/20 01:00 AM
Re: Cutting cast iron	justinp61	09/20/20 01:29 AM
Re: Cutting cast iron	cudaman1969	09/20/20 02:37 AM
Re: Cutting cast iron	Cab_Burge	09/20/20 03:03 AM
Re: Cutting cast iron	cudaman1969	09/20/20 02:44 PM
Re: Cutting cast iron	mr_340	09/20/20 07:15 PM
Re: Cutting cast iron	GODSCOUNTRY340	09/20/20 09:08 PM
Re: Cutting cast iron	Cab_Burge	09/21/20 12:25 AM
Re: Cutting cast iron	poorboy	09/21/20 01:28 AM
Re: Cutting cast iron	cudaman1969	09/21/20 07:08 AM
Re: Cutting cast iron	6PakBee	09/21/20 01:52 PM
Re: Cutting cast iron	mr_340	09/21/20 09:51 PM
Re: Cutting cast iron	375inStroke	09/21/20 11:30 PM
Re: Cutting cast iron	cudaman1969	09/22/20 03:48 AM
Re: Cutting cast iron	cudaman1969	09/22/20 03:58 AM
Re: Cutting cast iron	cudaman1969	09/22/20 04:01 AM
Re: Cutting cast iron	6PakBee	09/22/20 01:33 PM
Re: Cutting cast iron	cudaman1969	09/22/20 03:50 PM
Re: Cutting cast iron	6PakBee	09/22/20 05:55 PM
Re: Cutting cast iron	cudaman1969	09/22/20 09:04 PM
Re: Cutting cast iron	6PakBee	09/22/20 10:10 PM
Re: Cutting cast iron	cudaman1969	09/23/20 12:31 AM
Re: Cutting cast iron	IMGTX	09/30/20 04:53 PM
Re: Cutting cast iron	cudaman1969	10/01/20 07:54 PM
Re: Cutting cast iron	farmboy	10/03/20 02:49 AM
Re: Cutting cast iron	6PakBee	10/03/20 01:11 PM
Re: Cutting cast iron	farmboy	10/03/20 04:05 PM
Re: Cutting cast iron	cudaman1969	10/03/20 04:08 PM
Re: Cutting cast iron	roadrunninMark	10/03/20 06:01 PM
Re: Cutting cast iron	6PakBee	10/03/20 06:54 PM
Re: Cutting cast iron	GomangoCuda	09/20/20 12:35 PM

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To