How to handle Runs in clearcoat ?

Print Thread

Re: How to handle Runs in clearcoat ? [Re: 1_WILD_RT] #1214068 04/11/12 01:28 PM 04/11/12 01:28 PM
Joined: Jan 2003 Posts: 666 Anywhere the British Secret Se... M Moonraker mopar
Moonraker mopar M Joined: Jan 2003 Posts: 666 Anywhere the British Secret Se...	Quote: If you have steady hands use a single edge razor blade .... Grip the blade between the thumb & index fingers of both hands, center the blade, rest the heel of you hand on the car to help steady your self & take small shaving cuts off the top of the run... If you take an aggressive cut it may dig to deep so go slow... Al your want to do is get it close, that last little bit will sand out... Practice helps but ya gotta learn sometime & today is your day... Shaving is best done the day after you spray, the longer you wait the harder it gets... FWIW I use the blade straight but I use a layer of masking tape around the corner at each end of the blade... My buddy likes to put a slight bend in the middle of the blade so he has less blade close to the paint & better control of the cut... This works too but scares the crap out of me when I do it . Luckily I seldom get runs in the clear anymore. Always loved seeing that beatiful wet shine right after spraying only to come back in the booth 5 minutes later and see runs forming in it.

Entire Thread
Subject	Posted By	Posted
How to handle Runs in clearcoat ?	MileHighDart	04/11/12 04:12 PM
Re: How to handle Runs in clearcoat ?	herkamer	04/11/12 04:30 PM
Re: How to handle Runs in clearcoat ?	bonefish	04/11/12 04:48 PM
Re: How to handle Runs in clearcoat ?	1_WILD_RT	04/11/12 04:58 PM
Re: How to handle Runs in clearcoat ?	Moonraker	04/11/12 05:28 PM
Re: How to handle Runs in clearcoat ?	Moonraker	04/11/12 05:09 PM
Re: How to handle Runs in clearcoat ?	70Cuda383	04/11/12 05:23 PM
Re: How to handle Runs in clearcoat ?	Moonraker	04/11/12 11:38 PM
Re: How to handle Runs in clearcoat ?	bri440	04/12/12 01:03 AM
Re: How to handle Runs in clearcoat ?	MileHighDart	04/12/12 02:48 AM
Re: How to handle Runs in clearcoat ?	Mopargnome	04/12/12 05:51 AM
Re: How to handle Runs in clearcoat ?	BulletBob	04/12/12 06:05 AM
Re: How to handle Runs in clearcoat ?	GMP440	11/19/19 11:09 PM
Re: How to handle Runs in clearcoat ?	Liam	04/07/20 06:48 AM
Re: How to handle Runs in clearcoat ?	GomangoCuda	04/07/20 02:16 PM
Re: How to handle Runs in clearcoat ?	RTSrunner	04/15/12 04:59 AM
Re: How to handle Runs in clearcoat ?	71 FJ6 Charger	04/15/12 05:44 PM
Re: How to handle Runs in clearcoat ?	Pacnorthcuda	04/15/12 05:55 PM
Re: How to handle Runs in clearcoat ?	magnum440d100	04/15/12 06:45 PM
Re: How to handle Runs in clearcoat ?	Johnsnow Kornar	09/17/19 06:15 AM
Re: How to handle Runs in clearcoat ?	Pacnorthcuda	09/25/19 03:26 AM
Re: How to handle Runs in clearcoat ?	HUSTLESTUFF	09/17/19 12:12 PM
Re: How to handle Runs in clearcoat ?	HUSTLESTUFF	09/17/19 12:14 PM
Re: How to handle Runs in clearcoat ?	JDMopar	09/19/19 01:31 AM
Re: How to handle Runs in clearcoat ?	PAULS_340	09/25/19 02:11 AM
Re: How to handle Runs in clearcoat ?	Neil	09/25/19 02:20 AM
Re: How to handle Runs in clearcoat ?	Pacnorthcuda	09/25/19 03:28 AM
Re: How to handle Runs in clearcoat ?	MileHighDart	09/26/19 04:00 PM
Re: How to handle Runs in clearcoat ?	moparx	09/26/19 04:11 PM
Re: How to handle Runs in clearcoat ?	Salvador Johnson	11/02/19 08:17 PM
Re: How to handle Runs in clearcoat ?	jcc	11/03/19 01:07 AM
Re: How to handle Runs in clearcoat ?	emilies	11/19/19 06:25 PM

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To