This might make ya laugh
#890251
12/28/10 02:35 PM
12/28/10 02:35 PM
|
Joined: Mar 2007
Posts: 12,012 Finally a HUSKER again
Moparnut426
OP
I Live Here
|
OP
I Live Here
Joined: Mar 2007
Posts: 12,012
Finally a HUSKER again
|
I know Mickey Thompson did this, but I spoke with an engine builder, who is know for major failures, he was in my shop getting parts. Well, I was showing him my Demon build, hes a chevy guy, and didnt really care, but I was telling him I have to clearance a little bit on the push rod holes. Indybrocks have an offset rocker, and they are too close for comfort on the bottoms of the heads. Get this, He accually told me to stick the pushrods in a press and bend them just a touck to clear the heads. I said these are custom manton pushrods, and I dont want to shorten them, and I thought he was NUTS for blurting out that. He said they wont get shorter, At this time thank god the phone rang for service. I couldnt believe what I heard outa his mouth. Just goes to show ya that you have to reserch everything you have done anymore. If I took this guys shop a slug of race parts to build me an engine, and I heard this outa his mouth, Id load it up, and drive off QUICKLY!!! Just thought you guys would find this funny. KAsey
|
|
|
Re: This might make ya laugh
[Re: bwdst6]
#890254
12/28/10 03:01 PM
12/28/10 03:01 PM
|
Joined: Mar 2007
Posts: 12,012 Finally a HUSKER again
Moparnut426
OP
I Live Here
|
OP
I Live Here
Joined: Mar 2007
Posts: 12,012
Finally a HUSKER again
|
Well this is the same guy who told one of my customers to straighten his bent pushrod in his 360 mopar. He said mopars have a better pushrod geometry and are easier on them so if one is straightened its should be fine. He honestly is a kill to listen too. He is one of those guys who doesnt have much of a variation in his talk and ya dont ever know if he is serious or not, but when he starts talkin about his sbc stuff he gets really amped. Very funny, I should record his someday, that would be a little illegal i think, but funny as hell on here. Kasey
|
|
|
Re: This might make ya laugh
[Re: Moparnut426]
#890255
12/28/10 03:09 PM
12/28/10 03:09 PM
|
Joined: Aug 2003
Posts: 43,228 Bend,OR USA
Cab_Burge
I Win
|
I Win
Joined: Aug 2003
Posts: 43,228
Bend,OR USA
|
Quote:
Well this is the same guy who told one of my customers to straighten his bent pushrod in his 360 mopar. He said mopars have a better pushrod geometry and are easier on them so if one is straightened its should be fine. He honestly is a kill to listen too.
He is one of those guys who doesnt have much of a variation in his talk and ya dont ever know if he is serious or not, but when he starts talkin about his sbc stuff he gets really amped.
Very funny, I should record his someday, that would be a little illegal i think, but funny as hell on here.
Kasey
What works on a SB Chevy definitely doesn't work on a Ford or Mopar not for long at least if you follow his suggestions He must not be a farmer, they have a lot of common sense
Mr.Cab Racing and winning with Mopars since 1964. (Old F--t, Huh)
|
|
|
Re: This might make ya laugh
[Re: Cab_Burge]
#890256
12/28/10 03:20 PM
12/28/10 03:20 PM
|
Joined: Jan 2003
Posts: 8,028 Tulsa OK
Bad340fish
master
|
master
Joined: Jan 2003
Posts: 8,028
Tulsa OK
|
Well if you bend it besure you gusset the back side of it to reduce flex LOL.
68 Barracuda Formula S 340
|
|
|
Re: This might make ya laugh
[Re: Moparnut426]
#890257
12/28/10 03:31 PM
12/28/10 03:31 PM
|
Joined: Mar 2007
Posts: 9,336 South-Central (Sebring), FL
Commando1
master
|
master
Joined: Mar 2007
Posts: 9,336
South-Central (Sebring), FL
|
Quote:
He accually told me to stick the pushrods in a press and bend them just a touck to clear the heads. I couldnt believe what I heard outa his mouth.
Actually, I'm will to bet he was just pulling your chain to see what kind of reaction he's get. Kinda like when I told an old-timer know-it-all I had a of Metric tube cutter tool. He was pizzed I had a tool he didn't have....
|
|
|
Re: This might make ya laugh
[Re: Commando1]
#890258
12/28/10 03:41 PM
12/28/10 03:41 PM
|
Joined: Feb 2007
Posts: 970 Backwater, PA
bwdst6
Bob George Racing #1 Fan
|
Bob George Racing #1 Fan
Joined: Feb 2007
Posts: 970
Backwater, PA
|
Actually, knowing Indy they probably intended this modification!
Last edited by bwdst6; 12/28/10 04:28 PM.
This post is available in double vision where drunk.
|
|
|
Re: This might make ya laugh
[Re: Commando1]
#890259
12/28/10 03:42 PM
12/28/10 03:42 PM
|
Joined: Mar 2007
Posts: 12,012 Finally a HUSKER again
Moparnut426
OP
I Live Here
|
OP
I Live Here
Joined: Mar 2007
Posts: 12,012
Finally a HUSKER again
|
Quote:
Quote:
He accually told me to stick the pushrods in a press and bend them just a touck to clear the heads. I couldnt believe what I heard outa his mouth.
Actually, I'm will to bet he was just pulling your chain to see what kind of reaction he's get. Kinda like when I told an old-timer know-it-all I had a of Metric tube cutter tool. He was pizzed I had a tool he didn't have....
Well I would have origionally thought the same thing but when my customer came to him with his bent pushrod outa his 360, this guy told him he would straighten it for him and he could stick it back inn when he got back.
He came to my shop with it in his hand, still bent, but shocked.
Kasey
|
|
|
Re: This might make ya laugh
[Re: Dartwizer]
#890261
12/28/10 04:43 PM
12/28/10 04:43 PM
|
Joined: Dec 2008
Posts: 1,200 UK
602heavy
pro stock
|
pro stock
Joined: Dec 2008
Posts: 1,200
UK
|
|
|
|
Re: This might make ya laugh
[Re: 602heavy]
#890262
12/28/10 04:50 PM
12/28/10 04:50 PM
|
Joined: Jun 2003
Posts: 9,225 Charleston
sixpackgut
Drag Week Mod Champion
|
Drag Week Mod Champion
Joined: Jun 2003
Posts: 9,225
Charleston
|
i dig people that think outside the box. i would have never thought of that
Gen 3 power 6.22@110, 9.85@135 Follow @g3hemiswap on instagram
performance only racing, CRT, ultimate converter, superior design concepts, ThumperCarbs
|
|
|
Re: This might make ya laugh
[Re: sixpackgut]
#890263
12/28/10 05:35 PM
12/28/10 05:35 PM
|
Joined: Feb 2009
Posts: 1,019 Finland
mafo
super stock
|
super stock
Joined: Feb 2009
Posts: 1,019
Finland
|
maybe we need to come up with "flexible" pushrods, just bend to fit
-65 Valiant,420", all motor,2700#, dot tires, 8,42 @ 160,2
|
|
|
|
|