Re: Modifying Stock K-member
[Re: BBLM23]
#435653
08/12/09 04:13 PM
08/12/09 04:13 PM
|
Joined: Apr 2005
Posts: 1,880 USA
Ron Silva
top fuel
|
top fuel
Joined: Apr 2005
Posts: 1,880
USA
|
Here is my current one. A few holes to lighten it, lip removed all the way around, reinforced keyhole slots to tie the car down. My last one had the motor mounts removed and notched and boxed for the oil pan.
I think one member cuts the whole center out and installs a piece of 2X3 as the cross piece.
Bondo Bob??
SRT DEMON ONE SEAT
|
|
|
Re: Modifying Stock K-member
[Re: dustaboy74]
#435657
08/12/09 09:35 PM
08/12/09 09:35 PM
|
Joined: Jun 2005
Posts: 6,257 gulfport, ms, west mi
rowin4
master
|
master
Joined: Jun 2005
Posts: 6,257
gulfport, ms, west mi
|
I used 1/8" x 4" flat stock, cut it out square, similar to the one pictured. If I would do it again I would cut it wider and deeper towards the front. Would make getting the pan off or even putting the engine in easier, deep pans suck. Make sure if you do decide to do surgery on the cross member either leave it bolted in the car or weld it to a heavy steel bench to keep it from warping.
it's ok to butt heads, just don't do it with a butthead
|
|
|
Re: Modifying Stock K-member
[Re: rowin4]
#435658
08/12/09 09:41 PM
08/12/09 09:41 PM
|
Joined: Jan 2003
Posts: 4,244 Canada
Kam*Kuda
master
|
master
Joined: Jan 2003
Posts: 4,244
Canada
|
I will be cutting off the mounts as I am going to a motor plate
Last edited by Kam*Kuda; 08/12/09 09:43 PM.
1970 Barracuda Convertible 1968 Satellite Street Strip car 1654.5 Mustang 1955 Land Rover
|
|
|
Re: Modifying Stock K-member
[Re: Kam*Kuda]
#435659
08/12/09 09:43 PM
08/12/09 09:43 PM
|
Joined: Jan 2003
Posts: 4,244 Canada
Kam*Kuda
master
|
master
Joined: Jan 2003
Posts: 4,244
Canada
|
Tubes added for strength
Last edited by Kam*Kuda; 08/12/09 09:44 PM.
1970 Barracuda Convertible 1968 Satellite Street Strip car 1654.5 Mustang 1955 Land Rover
|
|
|
Re: Modifying Stock K-member
[Re: Stanton]
#435665
08/12/09 11:37 PM
08/12/09 11:37 PM
|
Joined: Feb 2005
Posts: 5,207 Menomonee Falls
DemonDust
master
|
master
Joined: Feb 2005
Posts: 5,207
Menomonee Falls
|
Quote:
In the photo above, where do the strut rods attach? I think you have the right idea ... if you're going to start hacking away the k-member its easier to fab what you need rather than carve off what you don't need. You've given me some ideas !!
Strut rods?
Here is another angle, hope it helps.
|
|
|
Re: Modifying Stock K-member
[Re: rebel]
#435669
08/13/09 11:55 AM
08/13/09 11:55 AM
|
Joined: Aug 2006
Posts: 1,613 Deerfield, Ohio
70dusterjohn
top fuel
|
top fuel
Joined: Aug 2006
Posts: 1,613
Deerfield, Ohio
|
Quote:
this is what happens when you have too much time on your hands in the off season.
Wait a Minute... The steerings on the wrong side... Looks good, but how is the pan clear...
|
|
|
Re: Modifying Stock K-member
[Re: 70dusterjohn]
#435670
08/13/09 02:21 PM
08/13/09 02:21 PM
|
Joined: Jan 2003
Posts: 4,852 KENTUCKY
69CHARGERMD
master
|
master
Joined: Jan 2003
Posts: 4,852
KENTUCKY
|
These are shots of my car,,,,work done by BondoBob,,,turned out awesome........ lost about 45 lbs,,,,,, and gained LOTS of clearance,,,,
|
|
|
|
|