|
Re: AMD quarters for 69' Coronet, what are the issues?
[Re: 6PACMAC]
#1717141
12/29/14 09:35 PM
12/29/14 09:35 PM
|
Joined: Nov 2005
Posts: 15,118
85086
moparpollack
Lil Herman
|
Lil Herman
Joined: Nov 2005
Posts: 15,118
85086
|
Some trimming by the roof gutter as they are made to be installed without a roof. Where the quarter meets the bumper requires some attention. But still a nice part in my opinion.
56 Plaza 63 D100 step side 67 Coronet, 68 Roadrunner, 69 Super Bees, 69 Coronet 500 convertible, 70 Roadrunner Post, 79 D150 360, and a severe case of Mopar a,d,d
|
|
|
Re: AMD quarters for 69' Coronet, what are the issues?
[Re: 6PACMAC]
#1717143
01/03/15 07:41 PM
01/03/15 07:41 PM
|
Joined: Jan 2003
Posts: 5,664
South Dakota
hotairballoonpilot
master
|
master
Joined: Jan 2003
Posts: 5,664
South Dakota
|
Just installed a pair on a 69 bee post car. No issues as I installed tail panel too. I never trimmed up any of it. I melted the lead out of the sail panel seam. Drilled out the drip rail spot welds by the 1/4 windows slipped it up under the roof and into the area in the drip rail area. Fit it over the factory wheel houses and it was all set. If you have a Facebook account look up Hartford's Best Paint and Body. I should have some pics there.
Corey
Contact Me about AMD Prices
|
|
|
Re: AMD quarters for 69' Coronet, what are the issues?
[Re: hotairballoonpilot]
#1717144
01/03/15 10:05 PM
01/03/15 10:05 PM
|
Joined: Dec 2004
Posts: 915
S.W. PA
6PACMAC
OP
super stock
|
OP
super stock
Joined: Dec 2004
Posts: 915
S.W. PA
|
Quote:
Just installed a pair on a 69 bee post car. No issues as I installed tail panel too. I never trimmed up any of it. I melted the lead out of the sail panel seam. Drilled out the drip rail spot welds by the 1/4 windows slipped it up under the roof and into the area in the drip rail area. Fit it over the factory wheel houses and it was all set. If you have a Facebook account look up Hartford's Best Paint and Body. I should have some pics there.
Corey
. Cool, I will check it out 
|
|
|
Re: AMD quarters for 69' Coronet, what are the issues?
[Re: 6PACMAC]
#1717145
01/05/15 01:24 AM
01/05/15 01:24 AM
|
Joined: Jan 2003
Posts: 18,632
jersey shore
flypaper
I hate Texas
|
I hate Texas
Joined: Jan 2003
Posts: 18,632
jersey shore
|
Quote:
I ordered a quarter for my 69' Bee from Summit. How is the fitment of these? I have read somewhere that the rear window flange is stamped at the wrong angle on the pillar. Any other problems?
i had problems with the rear window flange angle
and i had to add quite a bit of metal around the wheelwell radius to mate it up to the quarter properly.
|
|
|
Re: AMD quarters for 69' Coronet, what are the issues?
[Re: flypaper]
#1717146
01/05/15 12:57 PM
01/05/15 12:57 PM
|
Joined: Dec 2004
Posts: 915
S.W. PA
6PACMAC
OP
super stock
|
OP
super stock
Joined: Dec 2004
Posts: 915
S.W. PA
|
Quote:
Quote:
I ordered a quarter for my 69' Bee from Summit. How is the fitment of these? I have read somewhere that the rear window flange is stamped at the wrong angle on the pillar. Any other problems?
i had problems with the rear window flange angle
and i had to add quite a bit of metal around the wheelwell radius to mate it up to the quarter properly.
. I am going to replace the outer wheel house and the trunk floor extension so maybe I can get those areas to work with out too much grief  . The window flange I plan on leaving the original if I have to and cut the replacement panel to fit. We will see how it goes....
|
|
|
Re: AMD quarters for 69' Coronet, what are the issues?
[Re: 6PACMAC]
#1717147
01/06/15 12:35 AM
01/06/15 12:35 AM
|
Joined: Jan 2003
Posts: 18,632
jersey shore
flypaper
I hate Texas
|
I hate Texas
Joined: Jan 2003
Posts: 18,632
jersey shore
|
Quote:
Quote:
Quote:
I ordered a quarter for my 69' Bee from Summit. How is the fitment of these? I have read somewhere that the rear window flange is stamped at the wrong angle on the pillar. Any other problems?
i had problems with the rear window flange angle
and i had to add quite a bit of metal around the wheelwell radius to mate it up to the quarter properly.
. I am going to replace the outer wheel house and the trunk floor extension so maybe I can get those areas to work with out too much grief . The window flange I plan on leaving the original if I have to and cut the replacement panel to fit. We will see how it goes....
i replaced both of those parts also.
if i had to do it all over again,i would of spliced what i had to in the wheelwell area instead of replacing the whole thing
because you will be amazed at how bad it will fit all together..
they have retooled that outer wheelwell 3 times that i know of for that very reason.
good luck
|
|
|
Re: AMD quarters for 69' Coronet, what are the issues?
[Re: flypaper]
#1717148
01/06/15 03:13 PM
01/06/15 03:13 PM
|
Joined: Feb 2003
Posts: 18,582
Rust Belt, SW PA
Silver70
I Live Here
|
I Live Here
Joined: Feb 2003
Posts: 18,582
Rust Belt, SW PA
|
Quote:
i replaced both of those parts also.
if i had to do it all over again,i would of spliced what i had to in the wheelwell area instead of replacing the whole thing
because you will be amazed at how bad it will fit all together..
they have retooled that outer wheelwell 3 times that i know of for that very reason.
good luck
That's how I did a 70 runner I'm working on now and I had to add some metal to on to get it to fit how I liked. The ds fit better than the ps... that's one parts I have yet to get from any manufacturer that fit like an original.
68 Road Runner, 69 Belvedere, 71 Challenger Vert
340 barracuda, 01 Ram CTD, 95 Ram, 04 Ram, 85 Daytona turbo Z
66 GTO, 06 Magnum RT AWD. 07 Ram CTD, 07 Ram
|
|
|
Re: AMD quarters for 69' Coronet, what are the issues?
[Re: mccannix]
#1717153
01/07/15 06:25 PM
01/07/15 06:25 PM
|
Joined: Jan 2003
Posts: 74,992
U.S.S.A.
JohnRR
I Win
|
I Win
Joined: Jan 2003
Posts: 74,992
U.S.S.A.
|
Quote:
Too bad we're not closer...$200 for both and I cant give this pair of NOS takeoffs away.
Ontario, is kinda big , but not that far away , how far from the border ???
|
|
|
Re: AMD quarters for 69' Coronet, what are the issues?
[Re: JohnRR]
#1717154
01/07/15 06:47 PM
01/07/15 06:47 PM
|
Joined: Jan 2003
Posts: 4,784
Ontario, Canada
mccannix
master
|
master
Joined: Jan 2003
Posts: 4,784
Ontario, Canada
|
Jeez John...they were sold to a board member 20 minutes after I posted the pictures...should have said "$200 for both and cant give them away to any cheap Canucks up here". I'm 10 minutes from the NY state border where they are headed,... ...must be where all the money is. 
|
|
|
Re: AMD quarters for 69' Coronet, what are the issues?
[Re: 69_SIX_PACK]
#1717156
01/07/15 08:09 PM
01/07/15 08:09 PM
|
Joined: Jan 2003
Posts: 18,632
jersey shore
flypaper
I hate Texas
|
I hate Texas
Joined: Jan 2003
Posts: 18,632
jersey shore
|
Quote:
What happened to the rest of the car? Where do the reflectors go on Canadian quarter panels?
they look cut short in the back?
|
|
|
Re: AMD quarters for 69' Coronet, what are the issues?
[Re: flypaper]
#1717157
01/07/15 10:33 PM
01/07/15 10:33 PM
|
Joined: Oct 2003
Posts: 1,896
New England
Q5_Ed
top fuel
|
top fuel
Joined: Oct 2003
Posts: 1,896
New England
|
Wow can't believe I / John missed that. Then again I'm a road runner guy
WANTED : ...A New Sponsor or Winning Lottery Ticket
69 A12 road runner ,Q5, post coupe, 4 speed, former Drag car restored to "Driver" condition in the early 90's, Showing some Patina. SS/E Track Record Holder 1980 10.40 @ 130mph
|
|
|
Re: AMD quarters for 69' Coronet, what are the issues?
[Re: 6PACMAC]
#1717159
01/07/15 11:05 PM
01/07/15 11:05 PM
|
Joined: Jan 2003
Posts: 5,268
NY
70440+6bbl
master
|
master
Joined: Jan 2003
Posts: 5,268
NY
|
Quote:
Ya, those look like about a foot or so are cut off the rear. But they have real nice wheel openings, well worth the price
They sure were
They are going to donate bits and pieces for my Bee. Nice to keep it real with original metal.
|
|
|
|
|
