Griner VB guys - line pressure qun - Moparts Forums

Register Log In Moparts Forums Unlawfl's Race & Engine Tech Griner VB guys - line pressure qun

Print Thread

Griner VB guys - line pressure qun #1514410 10/09/13 10:35 AM 10/09/13 10:35 AM
Joined: Sep 2005 Posts: 621 Deep DEEP SOUTH LAD 524 OP mopar
LAD 524 OP mopar Joined: Sep 2005 Posts: 621 Deep DEEP SOUTH	Hey guys I just wondering what kinda line pressure you guys run with a LBA Griner TB/VB ? The trans has a 3.2 lever in an 800HP Hemi application. Also, which port do you use to check the fluid pressure in the 727 ? Thanks !! Last edited by ratbastad; 10/09/13 10:54 AM.

Re: Griner VB guys - line pressure qun [Re: LAD 524] #1514411 10/09/13 12:12 PM 10/09/13 12:12 PM
Joined: Jan 2003 Posts: 1,606 westerly, ri. usa 4 440lebaron top fuel
440lebaron top fuel 4 Joined: Jan 2003 Posts: 1,606 westerly, ri. usa	180 lbs per instructions REAR servo with brake on Last edited by 440lebaron; 10/09/13 12:22 PM. all parts are sold as is, all parts are considered used no warranties or returns paypal/check/money order, shipping is from zip 02891, buyer pays paypal fees 24% IRS 1099A plus 3% of part price, check/money order preferred site is not monitored 24/7 there might be a delay in response

Re: Griner VB guys - line pressure qun [Re: 440lebaron] #1514412 10/09/13 01:45 PM 10/09/13 01:45 PM
Joined: Dec 2012 Posts: 1,823 Wind Gap,Pa. S Sammy top fuel
Sammy top fuel S Joined: Dec 2012 Posts: 1,823 Wind Gap,Pa.	I use the 4.2 lever Why the 3 lever?

Re: Griner VB guys - line pressure qun [Re: Sammy] #1514413 10/09/13 06:26 PM 10/09/13 06:26 PM
Joined: Jan 2003 Posts: 1,812 Portsmouth, VA D DusterW2 top fuel
DusterW2 top fuel D Joined: Jan 2003 Posts: 1,812 Portsmouth, VA	With a Griner VB (high line pressure and high volume fluid circuits) you don't need high ratio levers. Some even use a 2.9. With a lower ratio, there is less chance of direct clutch/kickdown band timing problems. John 7881669-12-22G20B.pdf (158 downloads)

Re: Griner VB guys - line pressure qun [Re: DusterW2] #1514414 10/09/13 08:35 PM 10/09/13 08:35 PM
Joined: Jan 2003 Posts: 6,142 Melbourne , Australia LA360 master
LA360 master Joined: Jan 2003 Posts: 6,142 Melbourne , Australia	From memory they are factory set to 190 psi Alan Jones

Re: Griner VB guys - line pressure qun [Re: LA360] #1514415 10/10/13 10:22 AM 10/10/13 10:22 AM
Joined: Sep 2005 Posts: 621 Deep DEEP SOUTH LAD 524 OP mopar
LAD 524 OP mopar Joined: Sep 2005 Posts: 621 Deep DEEP SOUTH	Thanx Al - which port on the case is used to check like pressure ?

Re: Griner VB guys - line pressure qun [Re: LAD 524] #1514416 10/10/13 02:58 PM 10/10/13 02:58 PM
Joined: Feb 2007 Posts: 970 Backwater, PA B bwdst6 Bob George Racing #1 Fan
bwdst6 Bob George Racing #1 Fan B Joined: Feb 2007 Posts: 970 Backwater, PA	As an FYI. The more line pressure you run the more the pump works and the more parasitic lose you have from said pump. IOW, more line pressure robs HP and Griners have a lot of line pressure! Last edited by bwdst6; 10/10/13 02:59 PM. This post is available in double vision where drunk.

Re: Griner VB guys - line pressure qun [Re: bwdst6] #1514417 10/10/13 05:44 PM 10/10/13 05:44 PM
Joined: Jan 2003 Posts: 6,142 Melbourne , Australia LA360 master
LA360 master Joined: Jan 2003 Posts: 6,142 Melbourne , Australia	Comp Eliminator guys will wind the line pressure down to around 80 psi 190 psi might have been the max, and 165 psi was standard, my memory is fading.... Alan Jones

Re: Griner VB guys - line pressure qun [Re: bwdst6] #1514418 10/10/13 06:09 PM 10/10/13 06:09 PM
Joined: Jan 2003 Posts: 11,712 Portage,michigan B B3422W5 I Live Here
B3422W5 I Live Here B Joined: Jan 2003 Posts: 11,712 Portage,michigan	Quote: As an FYI. The more line pressure you run the more the pump works and the more parasitic lose you have from said pump. IOW, more line pressure robs HP and Griners have a lot of line pressure! Very true. Griner does such a good job with shift overlap though that I think his valvebodies might perhaps offset the pressure liability. And his brake releases super quick for pro tree stuff. 69 Dart GTS A4 Silver All steel, flat factory hood, 3360race weight 418 BPE factory replacement headed stroker, 565 lift solid cam Best so far, 10.40 @127 1/4 1.41 best 60 foot 6.60 at 103.90 1/8

Re: Griner VB guys - line pressure qun [Re: B3422W5] #1514419 10/13/13 07:20 AM 10/13/13 07:20 AM
Joined: Sep 2005 Posts: 621 Deep DEEP SOUTH LAD 524 OP mopar
LAD 524 OP mopar Joined: Sep 2005 Posts: 621 Deep DEEP SOUTH	Thanks fellas.... As an aside, Im also curious as to what band adjustment is use on F&R bands with the Griner VB and a 3.2 lever?

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To

Powered by UBB.threads™ PHP Forum Software 7.7.1