Chewed up a brake line fitting - options??
#141323
10/25/08 03:03 PM
10/25/08 03:03 PM
|
Joined: Oct 2004
Posts: 1,074 So Cal, USA
Fab64
OP
super stock
|
OP
super stock
Joined: Oct 2004
Posts: 1,074
So Cal, USA
|
In the process of removing a 40+ year-old brake line fitting from the distribution block, I chewed it up with my vice grips. The line itself (unfortunately, the one which runs to the rear brakes) is not damaged and the threaded part of the fitting looks fine (see pic). What are my options? - Can I just re-install it, using the vice grips? - Should I try to cut the line, put a new fitting on, and re-flare it? - Or do I need to replace the entire line? Any suggestions would be much appreciated, thanks! Roger
|
|
|
Re: Chewed up a brake line fitting - options??
[Re: Fab64]
#141324
10/25/08 03:25 PM
10/25/08 03:25 PM
|
Joined: Dec 2007
Posts: 7,759 So Cal
HealthServices
Why would you even post that?
|
Why would you even post that?
Joined: Dec 2007
Posts: 7,759
So Cal
|
restoring it?
Replace the whole line.
Driver and not messing with it again for another 5-10 years?
re-install it, using the vice grips.
As soon as you started having problems with removing the fitting you should have stopped, and got the right tool.
Actually you should of got the right tool to do the job to start with.
Last edited by HealthServices; 10/25/08 03:28 PM.
Allen
Here's a novel idea, let's not throw a bunch of parts at the car hoping it will fix the problem and instead spend a little time diagnosing it first.
Life was a little easier when I was just a wrench.
|
|
|
Re: Chewed up a brake line fitting - options??
[Re: Fab64]
#141326
10/25/08 03:43 PM
10/25/08 03:43 PM
|
Joined: Dec 2007
Posts: 7,759 So Cal
HealthServices
Why would you even post that?
|
Why would you even post that?
Joined: Dec 2007
Posts: 7,759
So Cal
|
Line/flare wrench, problem is for the occasional user the right tools are not cheap. Especially if you won’t use the set again for another 5 years. But it may be worth buying Ebay stuff and reselling afterwards. Even then there is no guarantee with a 30+ year old car
Last edited by HealthServices; 10/25/08 03:45 PM.
Allen
Here's a novel idea, let's not throw a bunch of parts at the car hoping it will fix the problem and instead spend a little time diagnosing it first.
Life was a little easier when I was just a wrench.
|
|
|
Re: Chewed up a brake line fitting - options??
[Re: Fab64]
#141327
10/25/08 03:43 PM
10/25/08 03:43 PM
|
Joined: Nov 2007
Posts: 21,835 Kirkland, Washington
Pacnorthcuda
Too Many Posts
|
Too Many Posts
Joined: Nov 2007
Posts: 21,835
Kirkland, Washington
|
The right tool is a line wrench, AKA a "Flare nut" wrench. Basically an six point box end wrench with an opening large enough to slip past the line. Gives additional gripping surface over just an open end wrench. Never use vise grips. Yea---like he posted above!
Last edited by Pacnorthcuda; 10/25/08 03:44 PM.
|
|
|
Re: Chewed up a brake line fitting - options??
[Re: Fab64]
#141330
10/25/08 03:55 PM
10/25/08 03:55 PM
|
Joined: Jan 2003
Posts: 10,968 Hampton, Ga.
70dart360
Green Meister
|
Green Meister
Joined: Jan 2003
Posts: 10,968
Hampton, Ga.
|
Should be a basic 3/16th line, no biggie, get a new piece from the local parts store, or just re-use it as long as it dont leak.
70 Dart Swinger
72 D-100 440 shortbed
76 Pinto, 68k 21mpg!
|
|
|
|
|