rods too wide???
#1081759
09/24/11 09:37 PM
09/24/11 09:37 PM
|
Joined: Dec 2008
Posts: 48 louisiana
71440dart
OP
member
|
OP
member
Joined: Dec 2008
Posts: 48
louisiana
|
i bought a 505 stroker from Hughes Engines, 4.25 stroke, and started final assembly today. the problem is i cannot put two rods on the same crank journal because they dont fit, they are chevy journals and measure like this- crank journal, 2.01, rods are 1.018 each. stock chevy rods measure .995 with the crank journal measuring 2.0. anyone ever run into this problem? i am going to call Hughes Engines Monday just wondering if anyone has ever had this problem. Thanks guys.
71 dodge dart race car,440/727 best so far: 11.23 @119
74 plymoth duster, 408SB/727
|
|
|
Re: rods too wide???
[Re: 71440dart]
#1081760
09/24/11 09:40 PM
09/24/11 09:40 PM
|
Joined: Jan 2004
Posts: 27,347 Today? Who Knows?
1_WILD_RT
Management Trainee
|
Management Trainee
Joined: Jan 2004
Posts: 27,347
Today? Who Knows?
|
Do they fit between the fillet but not down completely on the journal? If so look at the bearings & rods closely, one side is chamfered for clearance...
"The Armies of our ancestors were lucky, in that they were not trailed by a second army of pencil pushers."
|
|
|
Re: rods too wide???
[Re: 71440dart]
#1081762
09/24/11 09:48 PM
09/24/11 09:48 PM
|
Joined: Jun 2003
Posts: 52,972 Romeo MI
MR_P_BODY
Master
|
Master
Joined: Jun 2003
Posts: 52,972
Romeo MI
|
Quote:
i bought a 505 stroker from Hughes Engines, 4.25 stroke, and started final assembly today. the problem is i cannot put two rods on the same crank journal because they dont fit, they are chevy journals and measure like this- crank journal, 2.01, rods are 1.018 each. stock chevy rods measure .995 with the crank journal measuring 2.0. anyone ever run into this problem? i am going to call Hughes Engines Monday just wondering if anyone has ever had this problem. Thanks guys.
If they cant even fit in the throw area(a pair of rods) you can have the rods surface ground(I did that 1 time on my small block) I had to take .013 off of the inside wall of each rod... or have the crank cut wider(I JUST had this done on my 4" crank... it was cut for chevy dia but he screwed up and didnt cut the width... he did after I brought it back
|
|
|
Re: rods too wide???
[Re: MR_P_BODY]
#1081763
09/24/11 09:55 PM
09/24/11 09:55 PM
|
Joined: Dec 2008
Posts: 48 louisiana
71440dart
OP
member
|
OP
member
Joined: Dec 2008
Posts: 48
louisiana
|
if i do the rods i guess they have to be rebalanced? if i do the crank it would have to be nitrated and balanced again right? either way im not very happy with the parts that were supposed to be bolted in without any problems, hopefully it will all be worth it if i ever finish it. Thanks Mr. P body
71 dodge dart race car,440/727 best so far: 11.23 @119
74 plymoth duster, 408SB/727
|
|
|
Re: rods too wide???
[Re: 71440dart]
#1081764
09/24/11 10:04 PM
09/24/11 10:04 PM
|
Joined: Jun 2003
Posts: 52,972 Romeo MI
MR_P_BODY
Master
|
Master
Joined: Jun 2003
Posts: 52,972
Romeo MI
|
Quote:
if i do the rods i guess they have to be rebalanced? if i do the crank it would have to be nitrated and balanced again right? either way im not very happy with the parts that were supposed to be bolted in without any problems, hopefully it will all be worth it if i ever finish it. Thanks Mr. P body
Call up Hughes and tell them to replace the crank... on their dime
|
|
|
Re: rods too wide???
[Re: 71440dart]
#1081767
09/24/11 10:37 PM
09/24/11 10:37 PM
|
Joined: Nov 2004
Posts: 3,544 Syracuse,NY
CompWedgeEngines
master
|
master
Joined: Nov 2004
Posts: 3,544
Syracuse,NY
|
You have Mopar width rods for a Chevy journal. Are these K1 rods or Eagles perhaps? There is a Chevy width rod, and a Mopar width rod, that both could be used on a Chevy journal, but the crank has to have the appropriate width.
RIP Monte Smith
Your work is a reflection of yourself, autograph it with quality.
WD for Diamond Pistons,Sidewinder cylinder heads, Wiseco, K1 rods and cranks,BAM lifters, Morel lifters, Molnar Technologies, Harland Sharp, Pro Gear, Cometic, King Engine Bearings and many others.
|
|
|
Re: rods too wide???
[Re: CompWedgeEngines]
#1081768
09/24/11 10:48 PM
09/24/11 10:48 PM
|
Joined: Dec 2008
Posts: 48 louisiana
71440dart
OP
member
|
OP
member
Joined: Dec 2008
Posts: 48
louisiana
|
they are indeed K1 rods Competitionwedge. i had hughes balance it before they shipped it.
71 dodge dart race car,440/727 best so far: 11.23 @119
74 plymoth duster, 408SB/727
|
|
|
Re: rods too wide???
[Re: CompWedgeEngines]
#1081769
09/27/11 10:20 AM
09/27/11 10:20 AM
|
Joined: Dec 2008
Posts: 48 louisiana
71440dart
OP
member
|
OP
member
Joined: Dec 2008
Posts: 48
louisiana
|
i spoke with Craig yesterday at hughes, he told me to box the rods up and they would send a return slip and have them picked up and correct the problem by cutting the sides. i asked about the balance and he told me it would not make a big difference. however this doesnt make sense to me. what do you guys think?
71 dodge dart race car,440/727 best so far: 11.23 @119
74 plymoth duster, 408SB/727
|
|
|
Re: rods too wide???
[Re: 71440dart]
#1081770
09/27/11 10:35 AM
09/27/11 10:35 AM
|
Joined: Jun 2003
Posts: 52,972 Romeo MI
MR_P_BODY
Master
|
Master
Joined: Jun 2003
Posts: 52,972
Romeo MI
|
Quote:
i spoke with Craig yesterday at hughes, he told me to box the rods up and they would send a return slip and have them picked up and correct the problem by cutting the sides. i asked about the balance and he told me it would not make a big difference. however this doesnt make sense to me. what do you guys think?
To me thats the wrong way to do it... if you go with another set of chevy rods you would need to have those cut down... I would have the crank widened... and yes the balance would be off... I dont know how much
|
|
|
Re: rods too wide???
[Re: MR_P_BODY]
#1081771
09/27/11 10:39 AM
09/27/11 10:39 AM
|
Joined: Mar 2007
Posts: 12,013 Finally a HUSKER again
Moparnut426
I Live Here
|
I Live Here
Joined: Mar 2007
Posts: 12,013
Finally a HUSKER again
|
Quote:
Quote:
if i do the rods i guess they have to be rebalanced? if i do the crank it would have to be nitrated and balanced again right? either way im not very happy with the parts that were supposed to be bolted in without any problems, hopefully it will all be worth it if i ever finish it. Thanks Mr. P body
Call up Hughes and tell them to replace the crank... on their dime
I doubt he wants to go down that road, He will basically be made out as the moron, and made to feel like a school boy playing with a 5 hp briggs.
Probbly just have to have the rods narrowed, and rebalance things.
Kasey
|
|
|
Re: rods too wide???
[Re: Moparnut426]
#1081772
09/27/11 10:58 AM
09/27/11 10:58 AM
|
Joined: Dec 2008
Posts: 48 louisiana
71440dart
OP
member
|
OP
member
Joined: Dec 2008
Posts: 48
louisiana
|
so say something happens and i need rods down the road, the crank journal is too wide for a standard width chevy rod, and not wide enough for a mopar width rod with chevy journal. so this is a total disaster. so really Mr. P body is correct or i need a new crank.
71 dodge dart race car,440/727 best so far: 11.23 @119
74 plymoth duster, 408SB/727
|
|
|
Re: rods too wide???
[Re: Moparnut426]
#1081773
09/27/11 10:59 AM
09/27/11 10:59 AM
|
Joined: Oct 2004
Posts: 1,752 detroit area
moderncylinder
top fuel
|
top fuel
Joined: Oct 2004
Posts: 1,752
detroit area
|
we always cut rods to get a final rod-rod clearance dimension,,
no,, absolutely no,,, no,, no,, you will not have to rebalance it,, cutting .020 off a big end will take about 1-2 grams off,, which will change the bobweight 2-4 grams..
do you rebalance your motor when you run 5-20 oil as compared to 20-50 oil,,, thats prob bout the same difference
|
|
|
Re: rods too wide???
[Re: moderncylinder]
#1081774
09/27/11 11:06 AM
09/27/11 11:06 AM
|
Joined: Dec 2008
Posts: 48 louisiana
71440dart
OP
member
|
OP
member
Joined: Dec 2008
Posts: 48
louisiana
|
Quote:
we always cut rods to get a final rod-rod clearance dimension,,
no,, absolutely no,,, no,, no,, you will not have to rebalance it,, cutting .020 off a big end will take about 1-2 grams off,, which will change the bobweight 2-4 grams..
do you rebalance your motor when you run 5-20 oil as compared to 20-50 oil,,, thats prob bout the same difference
no, but i dont pay 350 dollars to change my oil weight either. i asked because i didnt know.
off topic: does a quart of 20-50 weigh the same as 5-20?
Last edited by 71440dart; 09/27/11 11:08 AM.
71 dodge dart race car,440/727 best so far: 11.23 @119
74 plymoth duster, 408SB/727
|
|
|
Re: rods too wide???
[Re: 71440dart]
#1081775
09/27/11 11:44 AM
09/27/11 11:44 AM
|
Joined: Nov 2003
Posts: 5,160 Texas
dannysbee
master
|
master
Joined: Nov 2003
Posts: 5,160
Texas
|
He is trying to help you. The oil weighs the same but because of the thicker viscosity there will be a larger volume of oil on the part.
Getting old just means you were smarter than some and luckier than others.
|
|
|
|
|