good drill size to prime a big block

Print Thread

Re: good drill size to prime a big block [Re: RapidRobert] #1311128 09/28/12 12:32 AM 09/28/12 12:32 AM
Joined: Jul 2006 Posts: 4,179 California mickm OP master
mickm OP master Joined: Jul 2006 Posts: 4,179 California	Quote: If you can would you note (& post) the 2 points where it oils i assume you mean where it oils the rocker shafts? my #4 cam journal is grooved, so it should provide constant oil, even if a small amount.

Entire Thread
Subject	Posted By	Posted
good drill size to prime a big block	mickm	09/26/12 09:49 PM
Re: good drill size to prime a big block	Twostick	09/26/12 09:59 PM
Re: good drill size to prime a big block	Dodgem	09/26/12 10:03 PM
Re: good drill size to prime a big block	Challenger 1	09/26/12 10:13 PM
Re: good drill size to prime a big block	dogdays	09/26/12 11:38 PM
Re: good drill size to prime a big block	bobs66440	09/26/12 11:57 PM
Re: good drill size to prime a big block	sthemi	09/27/12 12:03 AM
Re: good drill size to prime a big block	Challenger 1	09/27/12 12:35 AM
Re: good drill size to prime a big block	Exit1965	09/27/12 01:08 AM
Re: good drill size to prime a big block	RapidRobert	09/27/12 03:38 AM
Re: good drill size to prime a big block	AndyF	09/27/12 03:41 AM
Re: good drill size to prime a big block	Dodgem	09/27/12 03:51 AM
Re: good drill size to prime a big block	Cab_Burge	09/27/12 04:23 AM
Re: good drill size to prime a big block	therocks	09/27/12 12:06 PM
Re: good drill size to prime a big block	JohnRR	09/27/12 01:23 PM
Re: good drill size to prime a big block	Challenger 1	09/27/12 12:58 PM
Re: good drill size to prime a big block	446acuda	09/27/12 04:16 PM
Re: good drill size to prime a big block	Von	09/27/12 05:07 PM
Re: good drill size to prime a big block	mickm	09/27/12 06:59 PM
Re: good drill size to prime a big block	446acuda	09/27/12 08:26 PM
Re: good drill size to prime a big block	Fury Fan	09/27/12 09:15 PM
Re: good drill size to prime a big block	383man	09/27/12 09:05 PM
Re: good drill size to prime a big block	mickm	09/27/12 10:14 PM
Re: good drill size to prime a big block	RapidRobert	09/27/12 11:38 PM
Re: good drill size to prime a big block	mickm	09/28/12 04:32 AM
Re: good drill size to prime a big block	RapidRobert	09/28/12 05:03 AM
Re: good drill size to prime a big block	mickm	09/28/12 06:55 AM
Re: good drill size to prime a big block	bigblockbryan	09/28/12 09:24 AM
Re: good drill size to prime a big block	buildanother	09/28/12 02:04 PM
Re: good drill size to prime a big block	RapidRobert	09/28/12 02:54 PM
Re: good drill size to prime a big block	mickm	09/28/12 05:29 PM
Re: good drill size to prime a big block	mickm	09/30/12 10:48 PM

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To