swing out bar for certification?
#970372
04/10/11 12:55 PM
04/10/11 12:55 PM
|
Joined: Jan 2006
Posts: 501 Port Mcneill,B.C.Canada
Islandcuda
OP
mopar
|
OP
mopar
Joined: Jan 2006
Posts: 501
Port Mcneill,B.C.Canada
|
Hi guys I,m told my swing out bar will fail cert. for going in the 9,s cause not enough meet at the end of the bar and the hollow pin, anyone else run into this, thanks Tim
67 cuda new best 1.395 60 10.240 at 128.58mph
|
|
|
Re: swing out bar for certification?
[Re: Sixpak]
#970377
04/11/11 01:50 AM
04/11/11 01:50 AM
|
Joined: Jan 2006
Posts: 501 Port Mcneill,B.C.Canada
Islandcuda
OP
mopar
|
OP
mopar
Joined: Jan 2006
Posts: 501
Port Mcneill,B.C.Canada
|
I beleive they were morrison, not sure, my friend who is fabricater ordered and isntalled, has never been an issue, but after backhaving I may go into the 9,s and a freind tried to certify his and failed cause of hollow pin and not enough meet at the end of the bar.
67 cuda new best 1.395 60 10.240 at 128.58mph
|
|
|
Re: swing out bar for certification?
[Re: Scott58]
#970381
04/11/11 02:18 PM
04/11/11 02:18 PM
|
Joined: Nov 2003
Posts: 5,160 Texas
dannysbee
master
|
master
Joined: Nov 2003
Posts: 5,160
Texas
|
Don't see how that would be of much use on a door bar. Take too long to tighten it up. Now for a removable seat/belt bar two of those would be the thing.
Getting old just means you were smarter than some and luckier than others.
|
|
|
Re: swing out bar for certification?
[Re: mistress]
#970384
04/11/11 10:43 PM
04/11/11 10:43 PM
|
Joined: Jan 2006
Posts: 501 Port Mcneill,B.C.Canada
Islandcuda
OP
mopar
|
OP
mopar
Joined: Jan 2006
Posts: 501
Port Mcneill,B.C.Canada
|
Not enough timeto get that peice where I live, if I would of known this was an issue i would of ordered it when I put my back half kit from allston in. Oh well, after numerous emails and pics and phone calls I have to add on enough meat to the end of the bar to come to 1.625 inches from the hole. May be that measurement from center of hole but I,ll ad a little extra. The cert guy is coming to the island this weekend to cert a bunch of cars starting at one end of the island and ending up 3/4 of the way. Thanks guys
67 cuda new best 1.395 60 10.240 at 128.58mph
|
|
|
Re: swing out bar for certification?
[Re: Islandcuda]
#970385
04/11/11 10:46 PM
04/11/11 10:46 PM
|
Joined: Jan 2003
Posts: 4,085 Indiana
W5Duster436
master
|
master
Joined: Jan 2003
Posts: 4,085
Indiana
|
Here is what they put on mine and told me it would cert to 8.50 with no issues.
'70 Duster - SDSS 436 W5 4spd (Gone) '71 Dodge D100 '70 Dodge W100
|
|
|
|
|