|
Force Fed Fish..
#866088
11/28/10 11:33 PM
11/28/10 11:33 PM
|
Joined: Aug 2007
Posts: 475 HEMPSTEAD TX
CUUDAK
OP
mopar
|
OP
mopar
Joined: Aug 2007
Posts: 475
HEMPSTEAD TX
|
Ok folks, I am sure someone here has seen my build elsewhere!! I need to know how to contact Scott Brown...
I am building a 68 Formula "S" 383 Barracuda. Decided to go Turbo!! I am installing a 80mm B/W S480 with the upgraded 1.10 A/R housing and .83 wheel(quicker spool). My 383 was cracked soooo it now will be a 400 .060 over. It's still in the machine shop. I have almost everything for the install. I need info. on a Scott Brown cam I have and if it is usable for my application. Here are the specs.,
Specs: Intake Exhaust Lobe Lift .360 .353 Rocker ratio 1.5 1.5 Valve Lift .540 .530 Adv Dur 287 303 [Email]Dur@.50[/Email] 240 252 Lobe CentLin 108 116 Lash Hot .000 .000
Valve timing Open Close @.50 Int 12 BTDC 48 ABDC Exh 62 BBDC 10 ATDC
Lobe Seperation 112 Degree Intake Lobe 108
Looks to have good lobe seperation. I just do not know the rpm range!? Does anyone know how to contact Scott Brown???????
Am also looking at the Crower cams 32979 Turbomaster hyd camshaft
Some photos of the Turbo!!
Last edited by CUUDAK; 11/29/10 02:17 AM.
|
|
|
Re: Force Fed Fish..
[Re: CUUDAK]
#866090
11/29/10 10:51 PM
11/29/10 10:51 PM
|
Joined: Jul 2010
Posts: 3,502 SOUTH JERSEY
HEMIFRED
master
|
master
Joined: Jul 2010
Posts: 3,502
SOUTH JERSEY
|
is your turbo location device made of nylon or natural fibers ?
home of the Sox and Martin Hemi Duster
|
|
|
Re: Force Fed Fish..
[Re: HEMIFRED]
#866091
11/30/10 12:22 AM
11/30/10 12:22 AM
|
Joined: Jan 2005
Posts: 2,540 Milwaukee WI
TRENDZ
master
|
master
Joined: Jan 2005
Posts: 2,540
Milwaukee WI
|
I'll tell you right now, you need to block that heat crossover in the intake if you don't want unpredictable fueling problems.
"use it 'till it breaks, replace as needed"
|
|
|
Re: Force Fed Fish.. MySet-up!
[Re: CUUDAK]
#866103
12/05/10 09:59 PM
12/05/10 09:59 PM
|
Joined: Aug 2007
Posts: 475 HEMPSTEAD TX
CUUDAK
OP
mopar
|
OP
mopar
Joined: Aug 2007
Posts: 475
HEMPSTEAD TX
|
I did not elaborate but this is what I have in my set-up.
I don't know if you guys have seen the MadDart build but I Started mine soon after. This was to be a budget build with ebay stuff. My plan was twin Chinese GT45 turbos but could not bring myself to do it that way. I got the BW S480. The S480 80mm with upgraded 1.10 A/R housing and .83 wheel is from the clasiffied section in TTF $775.00 shipped, came with 5" V-band clamp and starter pipe and 5" to 4" reducer that I am not using. Oil feed and return kit from ebay $40 shipped The JDMSport intercooler is from ebay, nice heavy cast piece. Pressure tested at 30lbs for 2 days. No leaks. The piping and couplers came with the kit for $145.00 plus $50 shipping. I will probably change the couplers later due to them being 3 layer. They look like they will be ok tho. 2- 3" to 4" couplers and 2 4" clamps(Ebay) Don't remember price Bonnet/hat is a Spectre from ebay at $90 shipped, stud kit from autozone and it too is Spectre. Godspeed 50mm BOV is from ebay at $68 Godspeed 60mm Wastegate is from ebay at $120 shipped Hallman BMC is from ebay at $70 shipped 3/8" header flanges from ebay at $38 plus 15 shipping Ebay header kit(Weld-up) $119.00 plus shipping(JEGS) OBX T6 flange from ebay $20 shipped 5 OBX 3" flange kits at $30 ea. plus shipping(Ebay) 2- 5" 90's from MadDart $70 shipped Aeromotive A1000 pump and boost reference regulator $350 from a friend, barely used Aeromotive 16303 pump controller brand new from ebay $170.00 shipped 3" mandrel u's and straight pipe from local shop $100.00 K&N round filter from ebay $40 shipped Autometer boost gauge free from my Pops AEM afr gauge kit from ebay $150 shipped
$100 for 400 block from a friend 440 Source main girdle $275 plus shipping $396.00 for Eagle H-beam rods shipped from THmotorsports.com Forged 383 crank, mine Ported iron 906 heads, mine. Machine work and pistons-pins-rings-cam bearing, .060 overbore, Unknown $$ at this time. I still haven't got it from the machinist yet. Fel-Pro gasket set $60 shipped from ebay
Looking for a used Performer RPM now. PENDING!
Scott Brown cam $315.00 shipped
I know there is more that I am forgetting!!
Will be using the 833 4 speed that is in the car. 3.55's in place of the 3.91's in the 8 3/4 now, will get a set of 3.0? soon after.
Still need to get main and rod inserts, they will be Clevite77 hp's, around $160.00 Mopar billet timing set $80
All of this is going into my QQ1 Blue 1968 383 "H" code Formula "S" Fastback Barracuda
Also bought all new rotors-calipers-pads-bearings-seals-hoses to convert it to disc brakes from 10" drum. $331.00 Just ordered all the balljoints, bushings and tie-rods too! $140
Changing the K-frame from sandwich mount to spool type. Had this already!
Then once this is completed I will begin the Body and Paint work. Waiting on AMD to produce some sheetmetal pieces I need that is suppose to be out in early Spring 2011.
Last edited by CUUDAK; 12/05/10 10:07 PM.
|
|
|
|
|
|