73-76 A-Body Spool Mount K-Frame, Pros/Cons
#63483
05/25/08 09:12 PM
05/25/08 09:12 PM
|
Joined: Jan 2004
Posts: 1,230 Pittsburgh, PA
wayfarer1
OP
pro stock
|
OP
pro stock
Joined: Jan 2004
Posts: 1,230
Pittsburgh, PA
|
I am in the process of pulling the junk 318 and 904 from my 72 Swinger to start the resto. I can see evidence of some pretty heave pitting and surface rust on the stock V8 K-frame. I am thinking about replacing it and I know where there are 2 spool type k-frames, one has a complete disc brake setup on it.
My question is what are the benefits of the spool k-frame over the earlier biscuit type and are there and problems with the newer design that I should be concerned with.
Any help will be appreciated, Joe
Current Project: 72 Roadrunner 340/727/Petty Blue/White Roof Strobe Stripe/Black Bucket Interior
71 Demon project
|
|
|
Re: 73-76 A-Body Spool Mount K-Frame, Pros/Cons
[Re: wayfarer1]
#63484
05/25/08 09:43 PM
05/25/08 09:43 PM
|
Joined: Jan 2005
Posts: 469 In a van, down by the river
jmf340
mopar
|
mopar
Joined: Jan 2005
Posts: 469
In a van, down by the river
|
I don't know about any design flaws or benefits to the newer style spool mount, other than I feel it is easier to get the motor mount in the desired frame mount and slide a bolt through. It also tells you that the motor is situated correctly. Just my opinion though.
Got Mopar???
|
|
|
Re: 73-76 A-Body Spool Mount K-Frame, Pros/Cons
[Re: jmf340]
#63485
05/25/08 09:46 PM
05/25/08 09:46 PM
|
Anonymous
Unregistered
|
Anonymous
Unregistered
|
spool mount are superior in everyway.
|
|
|
Re: 73-76 A-Body Spool Mount K-Frame, Pros/Cons
#63486
05/25/08 10:16 PM
05/25/08 10:16 PM
|
Joined: Jan 2003
Posts: 27,468 So Cal
autoxcuda
Too Many Posts
|
Too Many Posts
Joined: Jan 2003
Posts: 27,468
So Cal
|
Quote:
spool mount are superior in everyway.
|
|
|
Re: 73-76 A-Body Spool Mount K-Frame, Pros/Cons
[Re: autoxcuda]
#63487
05/26/08 08:04 AM
05/26/08 08:04 AM
|
Joined: Jan 2003
Posts: 16,123 Grand Haven, MI
patrick
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 16,123
Grand Haven, MI
|
only negative is I think the front track on the later big-bolt pattern K's are a little wider...
1976 Spinnaker White Plymouth Duster, /6 A833OD 1986 Silver/Twilight Blue Chrysler 5th Ave HotRod **SOLD!*** 2011 Toxic Orange Dodge Charger R/T 2017 Grand Cherokee Overland 2014 Jeep Cherokee Latitude (holy crap, my daughter is driving)
|
|
|
Re: 73-76 A-Body Spool Mount K-Frame, Pros/Cons
[Re: patrick]
#63489
05/26/08 03:15 PM
05/26/08 03:15 PM
|
Joined: Jan 2003
Posts: 27,468 So Cal
autoxcuda
Too Many Posts
|
Too Many Posts
Joined: Jan 2003
Posts: 27,468
So Cal
|
Quote:
only negative is I think the front track on the later big-bolt pattern K's are a little wider...
Like Rocketride said, thats from the spindles/rotors. So if you do the factory type BBP conversion to a 67-72 A-body, you be at the same width.
I had the BBP conversion in my 68 K-member. Then I switched to just the 73-76 K-member. No width change and no engine height change either.
|
|
|
Re: 73-76 A-Body Spool Mount K-Frame, Pros/Cons
[Re: autoxcuda]
#63490
05/26/08 08:26 PM
05/26/08 08:26 PM
|
Joined: Jan 2004
Posts: 1,230 Pittsburgh, PA
wayfarer1
OP
pro stock
|
OP
pro stock
Joined: Jan 2004
Posts: 1,230
Pittsburgh, PA
|
So if I use the BBP disc brakes I have with the 73 spool k-member I should be good?
I have to get the old motor out first and evaluate the condition of the original k-frame before I make a final decision on replacing it.
Thanks for the info! Joe
Current Project: 72 Roadrunner 340/727/Petty Blue/White Roof Strobe Stripe/Black Bucket Interior
71 Demon project
|
|
|
Re: 73-76 A-Body Spool Mount K-Frame, Pros/Cons
[Re: wayfarer1]
#63491
05/26/08 08:56 PM
05/26/08 08:56 PM
|
Joined: Jan 2003
Posts: 27,468 So Cal
autoxcuda
Too Many Posts
|
Too Many Posts
Joined: Jan 2003
Posts: 27,468
So Cal
|
Quote:
So if I use the BBP disc brakes I have with the 73 spool k-member I should be good?
I have to get the old motor out first and evaluate the condition of the original k-frame before I make a final decision on replacing it.
Thanks for the info! Joe
Yes, that will be fine. If have to, you can re-use your 72 biscuit type K-member too.
Do any of these setups have lower control arms with sway bars tabs??
The one on the left is a 73-76. The one of the right is a 67-72
|
|
|
Re: 73-76 A-Body Spool Mount K-Frame, Pros/Cons
[Re: boden]
#63494
05/28/08 10:04 PM
05/28/08 10:04 PM
|
Joined: Feb 2003
Posts: 515 Dayton, Ohio
65cuda
mopar addict
|
mopar addict
Joined: Feb 2003
Posts: 515
Dayton, Ohio
|
you can buy a sway bar kit. another great thing about the spool mount is the sway bar goes through the k and doesn't hang below. also your not going to pull a motor mount apart.
65 Cuda 360,3.23 SG-13.97 @99.4, 88 D100, 2000 Kota Qcab, 71 Duster 416 11.84 @110., 73 Imp ,(2)72 & (1)71 Dart Swingers GarysMocars Legendary Dealer
|
|
|
Re: 73-76 A-Body Spool Mount K-Frame, Pros/Cons
[Re: boden]
#63496
05/28/08 11:14 PM
05/28/08 11:14 PM
|
Joined: Feb 2003
Posts: 1,024 In the twisties
RokketRide
super gas
|
super gas
Joined: Feb 2003
Posts: 1,024
In the twisties
|
Quote:
One con is that to you cannot install a 5.7 hemi with the TTI brackets using spool mounts. I actually cut 2 k-frames apart and made a hybrid. Top half is 72- for engine mounts, bottom half is 73+ style for the throught the k-frame sway bar.
|
|
|
Re: 73-76 A-Body Spool Mount K-Frame, Pros/Cons
[Re: RokketRide]
#63497
05/29/08 12:21 AM
05/29/08 12:21 AM
|
Joined: Jan 2004
Posts: 1,230 Pittsburgh, PA
wayfarer1
OP
pro stock
|
OP
pro stock
Joined: Jan 2004
Posts: 1,230
Pittsburgh, PA
|
Well, I found out today that a friend has a spool mount k-frame that I will be buying from him for a good price. He does not have the mounting brackets though. I know where there are 2 V8 Darts with the brackets still attached.
Is there an easy way to remove the mounting brackets with the engine still in the car or will I have to have the motor pulled to get them off?
Thanks to all for the great info!
Current Project: 72 Roadrunner 340/727/Petty Blue/White Roof Strobe Stripe/Black Bucket Interior
71 Demon project
|
|
|
Re: 73-76 A-Body Spool Mount K-Frame, Pros/Cons
[Re: wayfarer1]
#63498
05/29/08 12:34 AM
05/29/08 12:34 AM
|
Joined: Feb 2003
Posts: 515 Dayton, Ohio
65cuda
mopar addict
|
mopar addict
Joined: Feb 2003
Posts: 515
Dayton, Ohio
|
i got mine from advance auto parts. new and ready to bolt in.
65 Cuda 360,3.23 SG-13.97 @99.4, 88 D100, 2000 Kota Qcab, 71 Duster 416 11.84 @110., 73 Imp ,(2)72 & (1)71 Dart Swingers GarysMocars Legendary Dealer
|
|
|
Re: 73-76 A-Body Spool Mount K-Frame, Pros/Cons
[Re: 65cuda]
#63499
05/29/08 12:45 AM
05/29/08 12:45 AM
|
Joined: Jan 2003
Posts: 27,468 So Cal
autoxcuda
Too Many Posts
|
Too Many Posts
Joined: Jan 2003
Posts: 27,468
So Cal
|
Quote:
i got mine from advance auto parts. new and ready to bolt in.
Yes, spool mount motor mounts have the motor mount brackets integrated with them.
The long bolt that goes through the motor mount and to the K-member is sort of special. The washer fit the k-frame and IIRC, it's swaged in the center so it doesn't spin when you tighten it??
|
|
|
Re: 73-76 A-Body Spool Mount K-Frame, Pros/Cons
[Re: autoxcuda]
#63501
05/29/08 12:50 AM
05/29/08 12:50 AM
|
Anonymous
Unregistered
|
Anonymous
Unregistered
|
Quote:
Quote:
i got mine from advance auto parts. new and ready to bolt in.
Yes, spool mount motor mounts have the motor mount brackets integrated with them.
The long bolt that goes through the motor mount and to the K-member is sort of special. The washer fit the k-frame and IIRC, it's swaged in the center so it doesn't spin when you tighten it??
sounds bout right.
|
|
|
Re: 73-76 A-Body Spool Mount K-Frame, Pros/Cons
[Re: RokketRide]
#63502
05/29/08 01:56 AM
05/29/08 01:56 AM
|
Joined: Jan 2003
Posts: 27,468 So Cal
autoxcuda
Too Many Posts
|
Too Many Posts
Joined: Jan 2003
Posts: 27,468
So Cal
|
Quote:
Crap, I gotta find a set of those, my parts car didnt have them.
Might be available from dealer.
Same as any junkyard FMJ and R-body bolt. Maybe even others.
|
|
|
|
|