Broken motor mount ears on block
#447678
08/23/09 11:46 PM
08/23/09 11:46 PM
|
Joined: Oct 2003
Posts: 3,698 NE Oklahoma
Von
OP
master
|
OP
master
Joined: Oct 2003
Posts: 3,698
NE Oklahoma
|
This block came back from the machine shop with one ear broke on each side. Can this block still be used with the stock mounts? Id really like to not have to run a plate/elephant ears as it will be bear to mount my alt and get pulley alignment, but.... If it matters, I do use a chain on the drivers side to stop torquing. Opinions?
Last edited by Von; 08/24/09 08:23 AM.
|
|
|
Re: Motor mount ear pics
[Re: Von]
#447679
08/23/09 11:47 PM
08/23/09 11:47 PM
|
Joined: Oct 2003
Posts: 3,698 NE Oklahoma
Von
OP
master
|
OP
master
Joined: Oct 2003
Posts: 3,698
NE Oklahoma
|
72 RR, Pump gas 440, 452s, 3800 lbs, Corked, ET Radials,. 11.33@117.72.
Same car, bone stock 346s, 9.5 comp, baby solid. 12.24@110.
|
|
|
Re: Motor mount ear pics
[Re: Von]
#447680
08/23/09 11:48 PM
08/23/09 11:48 PM
|
Joined: Jan 2003
Posts: 75,020 U.S.S.A.
JohnRR
I Win
|
I Win
Joined: Jan 2003
Posts: 75,020
U.S.S.A.
|
If it were a Factory big block A body the driver side would not be a concern .
is it the one single ear on the other side ?
Last edited by Johnahah; 08/24/09 12:23 PM.
|
|
|
Re: Motor mount ear pics
[Re: JohnRR]
#447681
08/23/09 11:50 PM
08/23/09 11:50 PM
|
Joined: Oct 2003
Posts: 3,698 NE Oklahoma
Von
OP
master
|
OP
master
Joined: Oct 2003
Posts: 3,698
NE Oklahoma
|
[quote
is it the one sigle ear on the other side ?
If you mean the one single ear broke, yes. One ear on both sides is broke.
72 RR, Pump gas 440, 452s, 3800 lbs, Corked, ET Radials,. 11.33@117.72.
Same car, bone stock 346s, 9.5 comp, baby solid. 12.24@110.
|
|
|
Re: Motor mount ear pics
[Re: Von]
#447682
08/24/09 12:11 AM
08/24/09 12:11 AM
|
Joined: Jun 2003
Posts: 9,225 Charleston
sixpackgut
Drag Week Mod Champion
|
Drag Week Mod Champion
Joined: Jun 2003
Posts: 9,225
Charleston
|
Von, i just put a plate on my car and mounted the alternator down low, it wasnt hard and didnt cost a penny. if you decide to go that route i could send you pics
Gen 3 power 6.22@110, 9.85@135 Follow @g3hemiswap on instagram
performance only racing, CRT, ultimate converter, superior design concepts, ThumperCarbs
|
|
|
Re: Motor mount ear pics
[Re: sixpackgut]
#447683
08/24/09 12:12 AM
08/24/09 12:12 AM
|
Joined: Oct 2003
Posts: 3,698 NE Oklahoma
Von
OP
master
|
OP
master
Joined: Oct 2003
Posts: 3,698
NE Oklahoma
|
Quote:
Von, i just put a plate on my car and mounted the alternator down low, it wasnt hard and didnt cost a penny. if you decide to go that route i could send you pics
Thanks for the offer. If I go that route I'll hit you up for the pics.
Any opinion on the ears?
72 RR, Pump gas 440, 452s, 3800 lbs, Corked, ET Radials,. 11.33@117.72.
Same car, bone stock 346s, 9.5 comp, baby solid. 12.24@110.
|
|
|
Re: Motor mount ear pics
[Re: sixpackgut]
#447685
08/24/09 05:45 AM
08/24/09 05:45 AM
|
Joined: May 2004
Posts: 3,210 robin hood country
deaks
master
|
master
Joined: May 2004
Posts: 3,210
robin hood country
|
I use elephant ears and haven't had a problem, if you look in the tech section on BBD, It shows you how to make and fit them. Mick
69 Dart GTS 440 mopar .590 cam, Edelbrock heads, 3200# best et 6.45, 106.78, 10.14, 132.88 mph, 1.47 60ft best 60ft 1.36
|
|
|
Re: Motor mount ear pics
[Re: rebel]
#447687
08/24/09 11:08 AM
08/24/09 11:08 AM
|
Joined: Nov 2003
Posts: 6,293 Rock Springs
Bob_Coomer
master
|
master
Joined: Nov 2003
Posts: 6,293
Rock Springs
|
Call the shop and tell them to find the broken piece. They broke it, atleast they can find it. With this piece, it can be welded with a Ni rod, or stainless rod... IMO I wouldnt sweat it.You have the other two bolts to hold the engine. All of them on the other side, use the torque strap, and forget it.
[color:"red"]65 Hemi Belvedere coming soon [/color] [color:"#00FF00"]557" Indy engine 1.07 60ft 144mph in the 8th 2100 lbs package [/color]
|
|
|
Re: Motor mount ear pics
[Re: Bob_Coomer]
#447690
08/24/09 11:45 AM
08/24/09 11:45 AM
|
Joined: Oct 2003
Posts: 21,345 Marysville, O-H-I-O
70Cuda383
Too Many Posts
|
Too Many Posts
Joined: Oct 2003
Posts: 21,345
Marysville, O-H-I-O
|
exactly! I would be more upset with the machine shop, and make them fix it, and then re-check everything for square!
if THEY broke the ears off, then THEY need to fix it, and adding that much heat to the block, you might distort cylinder bores or something, so THEY should check everything to make sure it hasn't moved
but, bottom line, yes it can be fixed and use your stock motor mounts. I saw bob george's work fixing some blocks for his customers, and holy crap! I used to think a window in the side of the block meant it was junk, but not anymore!
**Photobucket sucks**
|
|
|
Re: Motor mount ear pics
[Re: Von]
#447691
08/24/09 12:21 PM
08/24/09 12:21 PM
|
Joined: Jan 2003
Posts: 75,020 U.S.S.A.
JohnRR
I Win
|
I Win
Joined: Jan 2003
Posts: 75,020
U.S.S.A.
|
Quote:
Quote:
is it the one single ear on the other side ?
If you mean the one single ear broke, yes. One ear on both sides is broke.
doooh , yes like that , you added the second picture as I was typing my reply , I didn't see it .
|
|
|
Re: Motor mount ear pics
[Re: 70Cuda383]
#447693
08/24/09 01:44 PM
08/24/09 01:44 PM
|
Joined: Oct 2003
Posts: 3,698 NE Oklahoma
Von
OP
master
|
OP
master
Joined: Oct 2003
Posts: 3,698
NE Oklahoma
|
Quote:
exactly! I would be more upset with the machine shop, and make them fix it, and then re-check everything for square!
if THEY broke the ears off, then THEY need to fix it, and adding that much heat to the block, you might distort cylinder bores or something, so THEY should check everything to make sure it hasn't moved
but, bottom line, yes it can be fixed and use your stock motor mounts. I saw bob george's work fixing some blocks for his customers, and holy crap! I used to think a window in the side of the block meant it was junk, but not anymore!
Well the ears were broke off 2 years ago when this block was machined. The guy who did the machine work is a good enough machinist, but a clown. Took about 6 months or more to get the block from him, finally got it home and didnt notice the ears were gone a few months down the line. Before I figured out he was a clown I took him the 440 block that is in my car at the moment. I paid to have the cam bearing journals corrected. (Journals too small from the factory, cam fit WAY too tight.) When I picked the block up he had scraped the bearings to fit my cam. No biggie, but I paid to have the block corrected. He also tried to charge me an extra 150 for a line hone. No dice, didnt ask for it, block didnt need it. Didnt pay for it and wont ever pay for it. Short verstion of the story, I never had a chance to get the ears back.
Like said above, no way I'll braze or weld on the block now. Warped cylinders dont appeal to me.
Just for giggles I think I'll fashion something and epoxy it. Maybe a thin bushing, epoxy it to the block, etc. Yeah, I know its a waste, but I want to see if the epoxy will adhere to the block and stay adhered.
72 RR, Pump gas 440, 452s, 3800 lbs, Corked, ET Radials,. 11.33@117.72.
Same car, bone stock 346s, 9.5 comp, baby solid. 12.24@110.
|
|
|
Re: Motor mount ear pics
[Re: Von]
#447694
08/24/09 01:55 PM
08/24/09 01:55 PM
|
Joined: Jun 2003
Posts: 9,225 Charleston
sixpackgut
Drag Week Mod Champion
|
Drag Week Mod Champion
Joined: Jun 2003
Posts: 9,225
Charleston
|
Von, i just took the shumacher torque strap off my car. sell it to you $50 if your interested
Gen 3 power 6.22@110, 9.85@135 Follow @g3hemiswap on instagram
performance only racing, CRT, ultimate converter, superior design concepts, ThumperCarbs
|
|
|
Re: Broken motor mount ears on block
[Re: Von]
#447696
08/24/09 07:45 PM
08/24/09 07:45 PM
|
Anonymous
Unregistered
|
Anonymous
Unregistered
|
build it up with JB weld - might take a couple of tubes by looking at the pix. I built up a mounting boss on my Jeep 4.0 and have run it 4 years on the strip with no prob;ems. You might drill and tap the mt and put a 1/4 20 bolt in to wrap the JB around - Make a form with tape and cardboard, then add the JB
|
|
|
|
|