I have a few sets of new ductile iron main caps available for 360/5.9 magnum engines. These are Mopar Performance caps. I have sets for both 360. The sets includes the first 4 caps. The center 3 caps are 4 bolt main. These are the same caps that came standard on R3 4 bolt blocks. I have installed these caps on a 340 before by milling off the ends of the center caps to leave them 2 bolt. See pictures for the 3 modified center caps installed on a 340 stroker engine. These caps are more stout than the stock caps and are an excellent upgrade for any high performance build. A line bore will be needed when installing new caps as well as some machining for the thrust bearing on the #3 cap.

Price is $340 shipped per set in the lower 48 states. I will ship internationally for the additional cost.

Email procketrichard@hotmail.com for more information.

I have a new set of 8 Mopar Performance pistons and wrist pins Mopar part# P4876973 for a 3.454” stroke crankshaft. Specs are 4.060” bore, 1/16, 1/16, 3/16 ring set, 0.984” wrist pin, flat top with ~ 5 cc eyebrows, listed by Mopar as 10.5 compression ratio. Compression height is ~ 1.72” per my measurement.

Price for the set is $480 shipped in the lower 48 states. I will ship internationally for the extra cost.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

I have a set of New BRC 4.030" forged flat top pistons and pins for a 3.79" stroke small block crankshaft. Compression height is ~ 1.57" and the ring lands are 1/16, 1/16 and 3/16. Pins are 0.984”. Approximately 6cc valve reliefs.

These pistons can be used in aftermarket race blocks or stock 360/5.9 magnum engine blocks with 4.030” finished bores.

Price is $475 shipped in the lower 48 states. I will ship elsewhere for the added cost.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

Chevy water pump to big block Mopar adapter. Don’t remember brand. $125 plus shipping from 70072 PayPal or postal money order

Afco Eliminator Front Shocks Single Adjustable . Used 1 season before upgrading to double adjustable. $300 plus shipping from 70072. Postal money order or PayPal friends and family

New, in-the-box RM-6073 QuickTime bellhousing for Chrysler big block, using 130T flywheel. All parts included as from the factory, $950 shipped within the continental 48 states. PM me here if interested, thanks.

For Sale Willy’s adjustable plate throttle stop for 4150 carb , great for index racing $433 now from
Summit asking $300 price negotiable shipping extra lbvracing@aol.com or pm

Rear trailer tie down brackets for most A, B, or E body vehicles (doesn’t fit the 7 ¼ rear axle). These piggyback onto the bottom of the stock shock plate mounting nuts and then 4 more nuts hold these tie down brackets on. You must have enough extra thread hanging down on the bottom of your U-bolts to fit the ¼” thick tie down bracket and another nut. No disassembly necessary, just slide the brackets over the extra thread on your U-bolts, install the included nuts, tighten them down and you’re done. Takes about 10 minutes to install. These eliminate all the hassles that come with using axle straps. Fits A, B, and E body cars with the standard shock plates like shown in the pictures. $60.00 per pair plus shipping. I also have these available for cars with CalTracs, same price. Made in the USA.
Email mrrandyj@aol.com

Used and works great!
Moroso 3-Vane Vacuum Pump #22640 (needs “1” -12 AN fitting)
Moroso Vacuum Regulator #22633
Moroso V-Belt Pulley #64885
Moroso Vacuum Pump Mount #63910

Accept PayPal+fees or U.S. Postal Money Order for payment.
$425 shipped to your door in the U.S.
PM me if you want it.

(NEW) ARC DRAG RACE CONTROL SWITCH PANEL

Accept PayPal +fees or U.S. Postal Money Order for payment
$175 shipped.
PM me if you want it.

Reactor Products New Old Stock from 2/94. 8 bolt crank to powerglide aluminum flywheel . $100 plus shipping from 70072. Postal money order , PayPal friends and family or add fees