For sale is a "NEW" in the box Holley HP Billet adjustable fuel pressure regulator. Part number 12-846. EFI applications. Bypass style. Adjustable from 15-65 PSI. -8AN o-ring inlet. -8AN o-ring outlet. -6AN o-ring return. $160 shipped in the 48 states. PM if interested.
For sale: Autometer Sport Comp II tachometer and gauges. Included are a 3690 tachometer with shift light and 3692 volt, 3637 water temp and 3627 oil pressure gauges. The gauges are all electrical gauges. I bought these for a car I used to own but sold the car before ever using them. I've been hanging on to them in case I bought another car but I don't think that's going to happen so I have decided to sell them. $450 for everything. Selling as a package only. No Paypal. gt340 at yahoo.com
For sale is a Howard's solid flat tappet cam for Mopar big blocks, part number CL722322-08. See links below for specifications. I bought this cam for my engine with the intention of taking the car to the track when the car was finished being restored along with the engine being built but I have changed my mind about racing the car and decided to go with a milder hydraulic cam instead. I had this cam installed in my engine on the engine stand but it never was run and is essentially new. $375 + shipping. I also have a new set of Comp Cams inner valve springs I was going to use with this cam and Edelbrock RPM heads that I am asking $45 for.
Thank you Moparts for the Ad Time to get somethings out of the garage to someone who can use them. Prices reduced! All items plus shipping from 61073 unless noted Ship or can meet within 35 miles of Rockford, IL Cashier's Check or Money Order
Pair Rancho RS99116 Single Adjustable Rear Shocks 16-1/2" to 22-1/2" Eye to Eye - $80 Moroso 65961 Air Pan Kit for 4500 Dominator - New in Box SOLD Fiberglass (Not Plastic) Racing Seat with Cover You need this for your Gasser Build! - PICK UP ONLY - $40 or best offer
Please message me on the Board Thanks for looking, John
Fits both big and small blocks. One bolt hole has been elongated so it fits early and later vibration dampers. $40 shipped in U.S. NO Paypal. U.S. check or money order only. VEIGHTPETE@GMAIL.COM
Crankshaft Pulley: P/N BCRL1CR Grooves: 1 Diameter: 5.2" Overall Length 2.3" Bolt Pattern: 6 Bolt 6061-T6 Billet Aluminum Made in the USA
CR12B early B-body fuel tank, has sump box welded in, sump box is about 1" below tank with 4" to 5" tall inside tank. Tank was coated inside and out by a company called Tank Renu. here is a link. https://www.gastankrenu.com/ Also has Aeromotive fuel filter with -10 outlet, -8 return,-6 vent. Also, can use a stock pickup, I have a new one to go with it. to plug the hole where it goes. 400$ Prefer local pick up, will ship at buyer's expense, I think it would be pretty expensive though. Located in Kansas City area. Pm if interested.
BRAND NEW billet big block oil pump cover for a remote oil filter. Machined for external pickup for either hemi or wedge but I believe can be used with internal pickup if the external pickup hole is plugged. Pickup fitting is 12an, remote fittings are 10an $200.firm plus the ride
Remote dual oil filter kit, 10an fittings and 3' of hose - brand new $80 firm plus the ride
Earls 12an screen type inline oil prefilter (for external p/u line) p/n 230312ERL - brand new $50 firm plus the ride
All prices in US $$ Parts located in Ontario, Shipping anywhere not an issue. Paypal F&F
I have a new PRW 1.6 ratio roller rocker arm kit containing all parts needed to install these rocker arms including steel bushed rocker arms, rocker arm shafts, spacers, shims, adjusters, steel shaft hold downs and hold down hardware. This kit is new in the box and is PRW part # 3231812.
Price is $500 shipped in the lower 48 states.
I will ship internationally for the additional shipping cost.
Email me at procketrichard@hotmail.com with any questions or for more pictures.
I have 11 pairs (one complete engine set plus 3 spare pairs) of new Mopar Performance solid roller lifters for small block still in their packages. Part number is P5249584. The roller wheel size is ~ 0.80”. The Mopar catalogue lists them for race blocks. See the included picture from the 1997 Mopar Performance catalogue for the description.
I fit these into my stock 340 block and they fit in nicely. On my block, the block required very minor grinding to a very small spot in the raised section of the valley to allow two of the eight lifter pairs to slide in. Contact was in the center of the link bar.
The price for the 11 pairs is $650 shipped in the lower 48 States. I will ship internationally for the added cost.
Email me at procketrichard@hotmail.com with any questions or for more pictures.
I have a new SCAT forged rotating assembly for 360 & 5.9 Magnum Mopar engines. All parts are new high-quality parts. Final cubic inches will be 408”. The assembly includes the following parts.
• SCAT forged 4.000” crankshaft part # 4-360-4000-6123 • SCAT forged H-beam connecting rods with APR 2000 bolts part # 2-360-6123-2124A • Diamond Forged flattop 4.030” bore pistons (0.030” oversize) part # 51026 • Trend wrist pins - 0.984” part # TPD-G9842750155 • Diamond wrist pin locks • Mahle file fit ring set with Moly ductile iron top rings part # MAH4035MS • Speed Pro Tri metal Competition Series rod bearings part # 8-7125CH • Clevite P-Series full groove main bearings part # MS-1266P
If you are looking for a 360 stroker with lower compression, I can substitute the pistons and connecting rods for new SRP 4.030” dished pistons part # 220156 (16.9 cc piston head volume) and new Eagle H-beam rods part # CRS6123C3D (360 stroker assembly only).
These rotating assemblies will need balancing.
The price for this complete kit with the Diamond flat top pistons and SCAT rods is $2,750 plus shipping cost.
The price for this complete kit with the SRP dished pistons and the Eagle H-beam rods is $2,600 plus shipping cost.
I also have a similar stroker assembly for a 340 with new Diamond 4.060” (0.020” overbore) flat top pistons, Perfect Circle file fit ring set with Moly ductile iron top rings part # 315-0036.065 and Speed Pro Tri metal Competition Series rod bearings part # 8-7125CH. Displacement would be 414 ci. This rotating assembly will need balancing.
The price for the complete 340 kit is $2,750 plus shipping cost.
I can also meet in CT.
Email me at procketrichard@hotmail.com with any questions or for more pictures.
I have a new SCAT forged rotating assembly for 340 Mopar engines. All parts are new high-quality parts. Final cubic inches will be 414”. The assembly includes the following parts.
• SCAT forged 4.000” crankshaft part # 4-340-4000-6123 • SCAT forged H-beam connecting rods with APR 2000 bolts part # 2-360-6123-2124A • Diamond Forged flattop 4.060” bore pistons (0.020” oversize) part # 51028 • Trend wrist pins part # TPD-G9842750155 • Diamond wrist pin locks • Perfect Circle file fit ring set with Moly ductile iron top rings part # 315-0036.065 • Speed Pro Tri metal Competition Series rod bearings part # 8-7125CH • Clevite P-Series full groove main bearings part # MS-1344P
This rotating assembly will need balancing.
Price for this complete kit is $2,750 plus shipping cost.
I can also meet in CT.
Email me at procketrichard@hotmail.com with any questions or for more pictures.
I have a new set of forged I beam connecting rods by Childs & Albert in the original box. American made in the 1990’s. Part number is 340-15B-2. Center to center length is 6.125”. Big end is for rod journals of 2.125” (small block Mopar) and small end is for wrist pins of 0.927”. Weight per rod is ~ 685 grams. See spec card in the pictures.
These are very stout rods, suitable for a high horsepower build.
Price is $850 shipped in the lower 48 states. I will ship internationally for the added cost.
Email me at procketrichard@hotmail.com with any questions or for more pictures.
I have a few sets of new ductile iron main caps available for 360/5.9 magnum engines. These are Mopar Performance caps. I have sets for both 360. The sets includes the first 4 caps. The center 3 caps are 4 bolt main. These are the same caps that came standard on R3 4 bolt blocks. I have installed these caps on a 340 before by milling off the ends of the center caps to leave them 2 bolt. See pictures for the 3 modified center caps installed on a 340 stroker engine. These caps are more stout than the stock caps and are an excellent upgrade for any high performance build. A line bore will be needed when installing new caps as well as some machining for the thrust bearing on the #3 cap.
Price is $340 shipped per set in the lower 48 states. I will ship internationally for the additional cost.
Email procketrichard@hotmail.com for more information.
I have a new set of 8 Mopar Performance pistons and wrist pins Mopar part# P4876973 for a 3.454” stroke crankshaft. Specs are 4.060” bore, 1/16, 1/16, 3/16 ring set, 0.984” wrist pin, flat top with ~ 5 cc eyebrows, listed by Mopar as 10.5 compression ratio. Compression height is ~ 1.72” per my measurement.
Price for the set is $480 shipped in the lower 48 states. I will ship internationally for the extra cost.
Email me at procketrichard@hotmail.com with any questions or for more pictures.
I have a set of New BRC 4.030" forged flat top pistons and pins for a 3.79" stroke small block crankshaft. Compression height is ~ 1.57" and the ring lands are 1/16, 1/16 and 3/16. Pins are 0.984”. Approximately 6cc valve reliefs.
These pistons can be used in aftermarket race blocks or stock 360/5.9 magnum engine blocks with 4.030” finished bores.
Price is $475 shipped in the lower 48 states. I will ship elsewhere for the added cost.
Email me at procketrichard@hotmail.com with any questions or for more pictures.
Afco Eliminator Front Shocks Single Adjustable . Used 1 season before upgrading to double adjustable. $300 plus shipping from 70072. Postal money order or PayPal friends and family
New, in-the-box RM-6073 QuickTime bellhousing for Chrysler big block, using 130T flywheel. All parts included as from the factory, $950 shipped within the continental 48 states. PM me here if interested, thanks.
I predict future happiness for Americans if they can prevent the government from wasting the labors of the people under the pretense of taking care of them. Thomas Jefferson
Freedom must be repurchased by every new generation General Daniel Jones, WW2 Tuskegee Airmen
For Sale Willy’s adjustable plate throttle stop for 4150 carb , great for index racing $433 now from Summit asking $300 new price ! $250 price negotiable shipping extra lbvracing@aol.com or pm
Rear trailer tie down brackets for most A, B, or E body vehicles (doesn’t fit the 7 ¼ rear axle). These piggyback onto the bottom of the stock shock plate mounting nuts and then 4 more nuts hold these tie down brackets on. You must have enough extra thread hanging down on the bottom of your U-bolts to fit the ¼” thick tie down bracket and another nut. No disassembly necessary, just slide the brackets over the extra thread on your U-bolts, install the included nuts, tighten them down and you’re done. Takes about 10 minutes to install. These eliminate all the hassles that come with using axle straps. Fits A, B, and E body cars with the standard shock plates like shown in the pictures. $60.00 per pair plus shipping. I also have these available for cars with CalTracs, same price. Made in the USA. Email mrrandyj@aol.com
Reactor Products New Old Stock from 2/94. 8 bolt crank to powerglide aluminum flywheel . $100 plus shipping from 70072. Postal money order , PayPal friends and family or add fees
Up for sale is a new in box msd gen 3 hemi controller and engine harness so you can run a carb. $700 -440 Edelbrock efi proflo 4 kit. Used 250 miles. Ran excellent. Took off for boosted application. $1600 Zip is 80550. Please send PM if interested, thank you
Last edited by 440lebaron; 10/18/2406:35 AM. Reason: sold
all parts are sold as is, all parts are considered used no warranties or returns paypal/check/money order, shipping is from zip 02891, buyer pays paypal fees 24% IRS 1099A plus 3% of part price, check/money order preferred site is not monitored 24/7 there might be a delay in response
596 Indy block B1 heads done by BES Indy R3 cam Bam lifters Manley vavle springs New T&D paired rockers 1.7 ratio Callies 4.625 crank Callies ultra rods Ross pistons Trend 7/16 .165 pushrods Koffels RB B1 intake (1 of 7 Made) C&S 1400 billet aerosol carb Indy offset dist Firecore wires Olson oil pan Moroso 3 vane vacuum pump Went 4.64 @146 in dragster all motor Has been 6.72 @ 199 on Spray Motor has 45 runs on it since freshening Any questions please call Scott Foster 937-538-8027 20,000 firm Motor in the picture of car attached
Listing my 2024 build motor to upgrade bigger and better. INDY 440-1 cnc "plus" heads with upgraded machining for TD paired rockers, steel thread inserts and doweled. NEW. Guides were replaced before heads were ever ran etc. NEW 22? passes ago. Manton stage5 pushrods Red zone PR oiling lifters .937 offset intakes. Ti 2.25 intake valves PSI springs. Cometic 4.53" head gaskets. Custom 55mm 4/7 swap cam from Scott Brown. Heads are about 60cc now. Indy first design 2x4 tunnelram with misc plenum spacers. Choice of '830' cfm or '1000' cfm carbs. Linkage, fuel lines regulator etc. I also have SS 2.25 intake valves and can alter the hardware to your combo. Includes the complete balanced recipe assembly with pistons, crank, rods etc. for a low-deck with 4.505ish bore. (can be used in an RB with different length rods.) Basically you'd need a block, most the oiling system (I have a new billet pump and dist drive) and timing drive. This combo will go 8.2's at 2815lbs you can calculate power if you wish. I may separate items. $13.500 Way cheaper than new and proven good stuff. PM me or two4eight-464 twenty 4eighty5 Sean
Last edited by 440lebaron; 12/11/2411:19 AM. Reason: price
all parts are sold as is, all parts are considered used no warranties or returns paypal/check/money order, shipping is from zip 02891, buyer pays paypal fees 24% IRS 1099A plus 3% of part price, check/money order preferred site is not monitored 24/7 there might be a delay in response
Re: For Sale - Race Parts - 4th Quarter
[Re: moparts]
#3267502 10/31/2405:50 PM10/31/2405:50 PM
20 gallon fuel cell, used in a street driven truck for about 6 months, need it gone, 100.00 plus shipping what you see is what you get, thanks, pm me here or email alilblacktruck@gmail.com
I have a Sportsman Racepak for sale. Just came back from Racepak with a clean bill of health. Has brand new driveshaft and power cable, pulled it from a car I purchased. Also have Water temp, oil pressure and boost/vaccum sensors. Also have a Rollbar mount and a carbon mount. Willing to make a package deal. Will not sell sensors separate. $750 for Sportsman. Will sell the package deal for $1350. PM me here or text/call 7 zero 7 9 8 zero 2 one 67
"I am not ashamed to confess I am ignorant of what I do not know."
"It's never wrong to do the right thing"
Re: For Sale - Race Parts - 4th Quarter
[Re: moparts]
#3267715 11/02/2409:06 AM11/02/2409:06 AM
1 Pr. aftermarket velocity stacks for 426 HEMI crossram or Max Wedge running 3705 carbs or Edelbrock aftermarket carbs $250.00 for the pair (708) 288-2879
Comp Cams rebuilt roller lifters part #828 for Small Block Mopar. Set of 16 includes 4 NEW lifters. These were rebuilt by Comp prior to when they discontinued their rebuild service. ***********SOLD*********
2 new pair of Comp 828-2 is $116 each x 2 =$232 just for the new ones. Complete new set $629
Jacobs Electronics FC1000 Ignition controller. $75 Shipped Jacobs Electronics Nitrous Mastermind controller $75 Shipped Don't know anything about them, Got both with a parts lot I bought. PM me here if interested.
J&W bell housing for adapting BB Mopar to Powerglide, brand new in the box with all hardware and instructions, only taken out of the box for pictures. 650 shipped in the Conus, also have 2 flywheels, one 6 bolt, one 8 bolt for extra $ if needed, pm me here or email alilblacktruck@gmail.com thanks
I have a set of hustle stuff / direct connection mechanical secondary carburetors for sale. The Holley list numbers on the outboards are 4783’s and the center is a 4782. These will need to be rebuilt as the have been setting many years. I have an extra center carb front bowl that goes with them. $1200.00 for the set plus any shipping cost. Payment would need to be USPS money order or PP as a gift only. Please PM me if interested, as I have extra pictures. Thank you, Matt
452 factory open chamber heads that were bought from muscle motors years back but were only ran maybe 1000 miles on a street, these have what muscle motors called stage 2 porting with the 2.14 intake valve and the 1.81 exhaust, they are sprung for up to a .650" solid cam, $800+shipping, P.M. me for pics SALE PENDING!
***SOLD*** Two primary and two secondary sight glass fuel bowls for 4150 double pumpers . Provisions in all four for accelerator pumps. No floats or pumps. Went with traditional looking bowls for my setup.. Postal money order only. Pm me here
Doing a little clearing out of things I won't be using, Indy RB 4500 MW port intake $500, used JE #213465 flat top pistons-4.375 bore, 4.15 stroke, 1.094 pin, 1.858 comp distance-$250 MP master cyl adapter 4 bolt to 2 bolt-NEW-$40 2 nitrous bottle adapters, 1 with pressure gauge-$40 for both NEW Melling SBM oil pump $40 Wilwood wheel spacers-#300-11961-NEW $25 PAIR Comp Cam #947-16 springs with retainers-$125 Manley #221447-16 springs $75 8.75 742 pumpkin, 35 spline Moser spool, 4.56 gear, less than 200 miles on gears-$700 Parts are in Lancaster, Ca, I accept PayPal, or if you have '38 Dodge truck stuff, trade?, contact me here by PM. file too big on intake, can text or email, can take pic of pumpkin, just had carpal tunnel surgery,
1970 'Cuda,Lime Light,499 Indy S/R's 10.70's @125,street driven ALOT! 1966 Barracuda 360,now a 5spd,Hemi Orange,Hot Rod Air, New daily driver-2003 Ram 2500 Cummins 5.9 '69 Valiant 2-dr, sleeper! New project---1938 Dodge truck, plan is a 360 with a A500, AC, Calvert rear susp., rack and pinion front with coils.
I bought multiple matched FG hoods from WS years back in one lot. The ones for sale are new never used, lift off untouched primed hoods. Likely will need some finish work for ideal finish as they are fiberglass, and they could be reinforced for hinge use IMO The hood pictured is NOT for sale which also fits a Polara 500, but it is a match, less the modifications of the hood pin cutouts and air supply, of what is offered for sale here. The stiffening ribs pictured were installed by WS and are included To keep costs reasonable for the buyer, delivery for a fee is possible east of Mississippi, they are located in SW Fla. $400ea OBO PM
1250 Holley Gen 3 Ultra Dominator Carburetor for sale....$900 + Shipping
So I have a newer 1250 carb, and it started life as a 3- circuit carb, and I had it converted to 2-circuit carb by Thumper carbs. It has not been used in a year and just sits in the box. Its the shiney polished silver and black. Was run on my 605 Hemi...and ran well. I can post actual pictures as soon as the camera is charged. I have double that price into it, and the old metering blocks come with it.
#TC-39, and he keeps good records. I have made a few minor changes and probably have all of them written down somewhere.
NOS Mopar Performance P5007140 Magnum R/T cylinder heads
Stock/Super Stock legal per sanctioning body rules (please check to verify) Brand new bare castings, sitting on the shelf 20 years Detail as shown in the video. Hens Teeth.
These were aftermarket general performance heads which underwent the process to be deemed Stock/Super Stock legal per sanctioning body roles (please verify), before being unceremoniously discontinued by the powers that be at Mopar Performance. They are not OEM parts and were never used in production.
Saved for 20 years to support a racer "sometime in the future". The future is now.
$1200 for the pair.
Local sale/Meetup within 50 miles of Metro Detroit/Oakland County greatly preferred.
I really do not want to ship these heavy iron heads but if you insist, I will ship at buyer's expense. Ground shipping quotes from the local Fed Ex terminal: To zip 94306: $403.90 for the pair To zip 53158: $217.26 for the pair Shipping quote based on 56.5LBs per cylinder head, packaged with foam padded (Edelbrock) packaging including insurance. Quotes for reference only: If you prefer your own shipping account or would like to use pirateship or similar, we can work something out.
Original packaging (basically useless for shipping: One Layer of cardboard) disintegrated during a move years ago, and was disposed of.
I no longer accept electronic payment
Please PM for more details and/or telephone number.
Very old but NEW unused stock hydraulic lifters for small block. Part #HT2011. They even smell old. All have a very consistent crown of .003 checked in my tool fixture. I'm going a different direction. $125 shipped. Postal money order only. PM me here.
Hey ya’ll. I have a new Pro 1 Elite Series 5-point Harness.
I bought them, installed them, then never got the car out of the garage before they expired. This would be PERFECT for cars that do not have to be sfi rated belts.
See the pic on the build options when I ordered them.
Edelbrock 361, 383 & 400 SIX PACK intake manifold, never been bolted to an engine, these are no longer being produced and may never be produced again $975.00 (708) 288-2879
Selling my Indy mod man 6 pack manifold for 440, also have a 4 barrel plate to go with it. These are over $1500 now. Asking $750 plus shipping standard port Sold thanks
I have a stock set of 906 heads, $100. Ported set of 906 stock heads with stock valves and with double springs ran 11.60 at 115 with these, need to be gone through $250, and ported set with oversized exhaust valves and single springs and steel retainer, still on my motor, about 1500 miles since rebuild, milled down to 80CC chambers. $300 all plus shipping or pickup in the Poconos
I have a fuel pressure regulator $25, I have a billet fuel pressure regulator $75, oversized intake valves for big block headsb$50, titanium retainer $75, steel 7 degree retainer take offs, $40
1 3/4" headers, unknown brand, 3" collectors. These were on an a b motor(edelbrock rpm heads) in a 67 b body. I had them coated 10 years ago and it's still pretty good. Asking $500.00 plus shipping. Text or call six three zero 674-3 nine2seven
Very lightly used Pro-Systems Venom VX 1040 4150 carburetor (maybe 10 passes). I had them spec this out for my 493 - see the attached spec sheets. I paid $878 for it but am no longer racing so I don't need it. I will sell it for $525+shipping. PM me if you're interested. Joe
For sale: Never used Cheetah Shifter 70001B with cover. I was planning on converting my Dart from a 4-speed to an automatic and bought this shifter to use. I have decided however to leave the car a 4-speed so I have no need for the shifter. I took it out of the box and set it with the cover over it on the hump in my car to see what it would look like but that's the only time it's been out of the box other than for the pictures. $500 including the cover. Money orders only, no Paypal.
3 Step Headers, with Merge collectors. Custom built by Steve Calligher. Fit: Mopar, Alston Chassis, with Big Block, with Brodix B1-BS Heads. Jet Hot coated when new. They worked great on 505 cubic inch engine. $700 or best offer
Mopar M1 Intake manifold 4500 dominator flange. Like new condition! Has threaded ports for methanol/ nitrous injection. $380 plus shipping. FYI- ship rates to increase after Jan 1 up 6%. send me a private message here with your contact info/ email and I can get you pics from my computer, thanks.
'70 Cuda "Badfish 2"- in the works
Home of MoPar University- We school 'em one at a time!!
(1) P7 DODGE NASCAR cylinder head, new, includes valves and springs. Pic's avail. $500/offer. Prefer not to ship. Pick up or arrange a meet up in Chicago area, could be at Chicagoland Mopar Swap Meet 2/9/25. PM me here. Thanks! Dave
![[Linked Image]](https://i.postimg.cc/029hdmFq/IMG-0416.jpg)
![[Linked Image]](https://i.imgur.com/RE4mVrMm.jpg)
![[Linked Image]](https://i.imgur.com/0IoH985m.jpg)
![[Linked Image]](https://i.imgur.com/XEAdGwfm.jpg)
![[Linked Image]](https://i.imgur.com/6DeHmjjm.jpg)
