First outing with new motor
#2917970
05/03/21 11:30 AM
05/03/21 11:30 AM
|
Joined: Jan 2003
Posts: 11,721 Portage,michigan
B3422W5
OP
I Live Here
|
OP
I Live Here
Joined: Jan 2003
Posts: 11,721
Portage,michigan
|
Test and tuned Fri night Went 10.77. Very healthy looking 6.78 at almost 101 in the 1/8. 1.44 60 foot Car was missing badly all the way down the track. Got worse further down track i got. It was mineshaft air Fri night. Then got hot over the weekend. Went from 800 feet to 4000 feet DA. Quite a swing..lol Anyhow, either new wires, moving the rev limiter from 7k to 8k( wasnt going past 6500-6600 anyway) but you never know... and turned up fuel pressure 1/2 a pound to 7 Something fixed it, didn't have time to try one thing at a time on a race weekend Anyhow, it did go 6.80 with a zero in much worse air. Think this thing has at worst a low to mid 60 in the 1/4 next time i get it in good air. The above pass was literally right off the trailer with brand new mill. Very happy for what it is. 565 gross lift flat tappet, heads peak at 272@550, eddies, weiand excellerator, and dinky 1 5/8 tube headers with muffs. Had 7 or 8 gallons of fuel in the 15 gallon cell, weighed 3320 with my 322 behind the wheel on the US131 scales.
Last edited by B3422W5; 05/03/21 11:31 AM.
69 Dart GTS A4 Silver All steel, flat factory hood, 3360race weight 418 BPE factory replacement headed stroker, 565 lift solid cam Best so far, 10.40 @127 1/4 1.41 best 60 foot 6.60 at 103.90 1/8
|
|
|
Re: First outing with new motor
[Re: JERICOGTX]
#2917985
05/03/21 12:00 PM
05/03/21 12:00 PM
|
Joined: Jan 2003
Posts: 11,721 Portage,michigan
B3422W5
OP
I Live Here
|
OP
I Live Here
Joined: Jan 2003
Posts: 11,721
Portage,michigan
|
Thanks Jeff. No, not bad at all. Got an issue with the pulley that bolts to the dampner that the alternator belt rides on..the bolts backing off. Had to constantly keep checking them. Put some lock washers on them, will see if it holds now. Never had an issue with that before
69 Dart GTS A4 Silver All steel, flat factory hood, 3360race weight 418 BPE factory replacement headed stroker, 565 lift solid cam Best so far, 10.40 @127 1/4 1.41 best 60 foot 6.60 at 103.90 1/8
|
|
|
Re: First outing with new motor
[Re: B3422W5]
#2917987
05/03/21 12:05 PM
05/03/21 12:05 PM
|
Joined: Jan 2003
Posts: 10,038 MN
JERICOGTX
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 10,038
MN
|
Thanks Jeff. No, not bad at all. Got an issue with the pulley that bolts to the dampner that the alternator belt rides on..the bolts backing off. Had to constantly keep checking them. Put some lock washers on them, will see if it holds now. Never had an issue with that before If it was easy, everyone would be doing it. No doubt you will pick away at it, and it will go faster.
69 GTX
68 Road Runner
|
|
|
Re: First outing with new motor
[Re: B3422W5]
#2918002
05/03/21 12:30 PM
05/03/21 12:30 PM
|
Joined: Aug 2003
Posts: 43,230 Bend,OR USA
Cab_Burge
I Win
|
I Win
Joined: Aug 2003
Posts: 43,230
Bend,OR USA
|
Thanks Jeff. No, not bad at all. Got an issue with the pulley that bolts to the dampner that the alternator belt rides on..the bolts backing off. Had to constantly keep checking them. Put some lock washers on them, will see if it holds now. Never had an issue with that before New motor, new harmonics maybe Maybe time for some red locktight
Mr.Cab Racing and winning with Mopars since 1964. (Old F--t, Huh)
|
|
|
Re: First outing with new motor
[Re: VernMotor]
#2918075
05/03/21 04:20 PM
05/03/21 04:20 PM
|
Joined: Jan 2003
Posts: 13,375 Marion, South Carolina [><]
an8sec70cuda
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 13,375
Marion, South Carolina [><]
|
Good deal Don! Sounds like it's running strong!
CHIP '70 hemicuda, 575" Hemi, 727, Dana 60 '69 road runner, 440-6, 18 spline 4 speed, Dana 60 '71 Demon, 340, low gear 904, 8.75 '73 Chrysler New Yorker, 440, 727, 8.75 '90 Chevy 454SS Silverado, 476" BBC, TH400, 14 bolt '06 GMC 2500HD LBZ Duramax
|
|
|
Re: First outing with new motor
[Re: B3422W5]
#2918079
05/03/21 04:38 PM
05/03/21 04:38 PM
|
Joined: Aug 2003
Posts: 4,688 On the parachute mount
n20mstr
master
|
master
Joined: Aug 2003
Posts: 4,688
On the parachute mount
|
Test and tuned Fri night Went 10.77. Very healthy looking 6.78 at almost 101 in the 1/8. 1.44 60 foot Car was missing badly all the way down the track. Got worse further down track i got. It was mineshaft air Fri night. Then got hot over the weekend. Went from 800 feet to 4000 feet DA. Quite a swing..lol Anyhow, either new wires, moving the rev limiter from 7k to 8k( wasnt going past 6500-6600 anyway) but you never know... and turned up fuel pressure 1/2 a pound to 7 Something fixed it, didn't have time to try one thing at a time on a race weekend Anyhow, it did go 6.80 with a zero in much worse air. Think this thing has at worst a low to mid 60 in the 1/4 next time i get it in good air. The above pass was literally right off the trailer with brand new mill. Very happy for what it is. 565 gross lift flat tappet, heads peak at 272@550, eddies, weiand excellerator, and dinky 1 5/8 tube headers with muffs. Had 7 or 8 gallons of fuel in the 15 gallon cell, weighed 3320 with my 322 behind the wheel on the US131 scales.
Very Nice, sounds like a great running streeter. A lil nitrous plate would really make you some $$$$ here and there.
....BAD A$$ STREET CAR.....
|
|
|
Re: First outing with new motor
[Re: MR_P_BODY]
#2918089
05/03/21 04:54 PM
05/03/21 04:54 PM
|
Joined: Jan 2003
Posts: 11,721 Portage,michigan
B3422W5
OP
I Live Here
|
OP
I Live Here
Joined: Jan 2003
Posts: 11,721
Portage,michigan
|
Don.. its just lean.. jet it up... good start Don I put 4 in the front and back, now its pig rich, but wasn't gonna mess with it bracket racing Saturday and Sunday. It was COLD Fri night. Plugs looked mighty lean..lol
69 Dart GTS A4 Silver All steel, flat factory hood, 3360race weight 418 BPE factory replacement headed stroker, 565 lift solid cam Best so far, 10.40 @127 1/4 1.41 best 60 foot 6.60 at 103.90 1/8
|
|
|
Re: First outing with new motor
[Re: B3422W5]
#2918112
05/03/21 05:53 PM
05/03/21 05:53 PM
|
Joined: Jun 2003
Posts: 52,972 Romeo MI
MR_P_BODY
Master
|
Master
Joined: Jun 2003
Posts: 52,972
Romeo MI
|
Don.. its just lean.. jet it up... good start Don I put 4 in the front and back, now its pig rich, but wasn't gonna mess with it bracket racing Saturday and Sunday. It was COLD Fri night. Plugs looked mighty lean..lol Yes it might show rich now but your gonna have to zero in on the jetting.. thats a a big swing on the temp and when it warms up some you jet up some
|
|
|
Re: First outing with new motor
[Re: mopar dave]
#2918342
05/04/21 10:09 AM
05/04/21 10:09 AM
|
Joined: Jan 2003
Posts: 11,721 Portage,michigan
B3422W5
OP
I Live Here
|
OP
I Live Here
Joined: Jan 2003
Posts: 11,721
Portage,michigan
|
Congrats Don. Nice first outing. What size carb you runnin? What main jetting and what high speed bleeds? Jets were 76/84 850 race brawler. Swapped to 80/88jets... gonna change them back... Hi speed 33/33 Idle 73/73 Was considering swapping the idles to around 60.. seem big to me.... doesn't idle real cleanly.... just off idle there is sometimes just a bit of a stumble/ hesitation. Dont see it when i footbrake it from 2k though. Just at tip in. So wanted to try going down some to richen it up a bit. Is my thinking correct?
Last edited by B3422W5; 05/04/21 10:51 AM.
69 Dart GTS A4 Silver All steel, flat factory hood, 3360race weight 418 BPE factory replacement headed stroker, 565 lift solid cam Best so far, 10.40 @127 1/4 1.41 best 60 foot 6.60 at 103.90 1/8
|
|
|
|
|