Re: Hydraulic roller
[Re: twayne24365]
#2813157
08/25/20 05:10 PM
08/25/20 05:10 PM
|
Joined: Jan 2003
Posts: 1,761 Windsor, ON, Canada
Diplomat360
top fuel
|
top fuel
Joined: Jan 2003
Posts: 1,761
Windsor, ON, Canada
|
Take a look at this thread of mine on here about something very similar. For me this was a move from a hydraulic flat tappet to a hydraulic roller setup. I do not have this build finished yet, so unfortunately no feedback, although I am interested in what otherws will say.
|
|
|
Re: Hydraulic roller
[Re: Diplomat360]
#2813164
08/25/20 05:29 PM
08/25/20 05:29 PM
|
Joined: Dec 2013
Posts: 4,687 Wichita
GY3
master
|
master
Joined: Dec 2013
Posts: 4,687
Wichita
|
I run a Howards hydraulic roller and absolutely love it!
'63 Dodge 330 11.19 @ 121 mph Pump gas, n/a, through the mufflers on street tires with 3.54's. 3,600 lbs. 10.01 @ 133mph with a 250 shot of nitrous an a splash of race gas. 1.36 60 ft. 3,700 lbs.
|
|
|
Re: Hydraulic roller
[Re: GY3]
#2813284
08/25/20 09:17 PM
08/25/20 09:17 PM
|
Joined: Oct 2006
Posts: 1,264 New York, USA
Chargerfan68
pro stock
|
pro stock
Joined: Oct 2006
Posts: 1,264
New York, USA
|
I run a Howards hydraulic roller and absolutely love it! Just curious, do you run the “street” lifters or the “max effort” lifters. I have them going into a build that should be done in a few weeks. Hoping they perform flawless for a good long time. Fingers crossed.
Last edited by Chargerfan68; 08/25/20 09:18 PM.
1.50 60Ft. , 10.75@ 127MPH Hauling 3900 LBS.
|
|
|
Re: Hydraulic roller
[Re: Chargerfan68]
#2813337
08/25/20 11:05 PM
08/25/20 11:05 PM
|
Joined: Dec 2013
Posts: 4,687 Wichita
GY3
master
|
master
Joined: Dec 2013
Posts: 4,687
Wichita
|
I run a Howards hydraulic roller and absolutely love it! Just curious, do you run the “street” lifters or the “max effort” lifters. I have them going into a build that should be done in a few weeks. Hoping they perform flawless for a good long time. Fingers crossed. Street.
'63 Dodge 330 11.19 @ 121 mph Pump gas, n/a, through the mufflers on street tires with 3.54's. 3,600 lbs. 10.01 @ 133mph with a 250 shot of nitrous an a splash of race gas. 1.36 60 ft. 3,700 lbs.
|
|
|
Re: Hydraulic roller
[Re: twayne24365]
#2813830
08/27/20 06:43 AM
08/27/20 06:43 AM
|
Joined: Jul 2013
Posts: 84 Norway
cudaerik
member
|
member
Joined: Jul 2013
Posts: 84
Norway
|
six summers now with lots of street miles with Hughes Racing hydraulic roller with Morel 5319 lifters, just make sure your lifter bores are within spec. if oval our out of spec have them bushed.
1970 Plymouth Cuda, 512cid on 230 400 block, 5 speed manual.(TKO 600) 1970 Dodge Charger 500, 446cid, 5speed manual.(TKO 600) 1969 Plymouth Roadrunner, 383cid, 5speed manual (Tremec TKX)
|
|
|
|
|