ATI Damper Pulley Alignment?
#2690652
08/23/19 02:32 PM
08/23/19 02:32 PM
|
Joined: Jan 2003
Posts: 1,811 North Dakota
Azzkikrcuda
OP
top fuel
|
OP
top fuel
Joined: Jan 2003
Posts: 1,811
North Dakota
|
Looking at getting ATI Damper part number 917470E, Which lists as working with stock cover and pulley alignment. Can anyone confirm stock pulleys will line up with this Damper. Thanks.
The only Carbs I care about are under the hood!
|
|
|
Re: ATI Damper Pulley Alignment?
[Re: Azzkikrcuda]
#2690659
08/23/19 02:52 PM
08/23/19 02:52 PM
|
Joined: Aug 2003
Posts: 43,315 Bend,OR USA
Cab_Burge
I Win
|
I Win
Joined: Aug 2003
Posts: 43,315
Bend,OR USA
|
Is that the part number for a BB? If so what year are you working on?
Mr.Cab Racing and winning with Mopars since 1964. (Old F--t, Huh)
|
|
|
Re: ATI Damper Pulley Alignment?
[Re: Cab_Burge]
#2690687
08/23/19 05:09 PM
08/23/19 05:09 PM
|
Joined: Jan 2003
Posts: 1,811 North Dakota
Azzkikrcuda
OP
top fuel
|
OP
top fuel
Joined: Jan 2003
Posts: 1,811
North Dakota
|
Internal balance, Big Block mopar
The only Carbs I care about are under the hood!
|
|
|
Re: ATI Damper Pulley Alignment?
[Re: Azzkikrcuda]
#2690719
08/23/19 06:57 PM
08/23/19 06:57 PM
|
Joined: Nov 2007
Posts: 277 MN
Willie68coronet
enthusiast
|
enthusiast
Joined: Nov 2007
Posts: 277
MN
|
Looking at getting ATI Damper part number 917470E, Which lists as working with stock cover and pulley alignment. Can anyone confirm stock pulleys will line up with this Damper. Thanks. Yeah I have that damper on my 440 with stock timing cover and pulleys. Lined up straight for me
'68 Coronet 500 w/ Indy EZ-1 headed 446, 727 trans, 9" rear First day at the track with SUV street tires and no traction: 1.688 60', 7.24 @ 101.79 in the 1/8 mile
Great customer service from: DominicThumper Carbs, B3 racing engines, Porter Racing Engines, A-1 torque converter's, Quick Performance, Racer Brown Cams, R&R Performance, Manton pushrods
|
|
|
Re: ATI Damper Pulley Alignment?
[Re: Azzkikrcuda]
#2690740
08/23/19 08:47 PM
08/23/19 08:47 PM
|
Joined: Feb 2005
Posts: 4,321 Prospect, PA
BSB67
master
|
master
Joined: Feb 2005
Posts: 4,321
Prospect, PA
|
ATI 917470E
I believe that I need to use a 0.060" spacer behind the WP pulley.
Last edited by BSB67; 08/23/19 08:48 PM.
|
|
|
Re: ATI Damper Pulley Alignment?
[Re: Azzkikrcuda]
#2690895
08/24/19 11:29 AM
08/24/19 11:29 AM
|
Joined: Nov 2007
Posts: 277 MN
Willie68coronet
enthusiast
|
enthusiast
Joined: Nov 2007
Posts: 277
MN
|
I bought the water pump spacer he mentioned but didn't need it when I mocked everything up.
I used Superformance gaskets everywhere, which are thicker than fel pro. That could be a difference or some other variable.
'68 Coronet 500 w/ Indy EZ-1 headed 446, 727 trans, 9" rear First day at the track with SUV street tires and no traction: 1.688 60', 7.24 @ 101.79 in the 1/8 mile
Great customer service from: DominicThumper Carbs, B3 racing engines, Porter Racing Engines, A-1 torque converter's, Quick Performance, Racer Brown Cams, R&R Performance, Manton pushrods
|
|
|
Re: ATI Damper Pulley Alignment?
[Re: second 70]
#2690903
08/24/19 12:16 PM
08/24/19 12:16 PM
|
Joined: Feb 2005
Posts: 4,321 Prospect, PA
BSB67
master
|
master
Joined: Feb 2005
Posts: 4,321
Prospect, PA
|
.060 is less than 1/16" I bet the factory wasn't that precise. And it's with an aftermarket WP housing and pump. WP to block and WP housing to WP gaskets are 0.030". At the end of the day, I would say it lines up as best as one could expect considering the stack/variables.
|
|
|
Re: ATI Damper Pulley Alignment?
[Re: Azzkikrcuda]
#2690939
08/24/19 02:43 PM
08/24/19 02:43 PM
|
Joined: Jan 2003
Posts: 1,811 North Dakota
Azzkikrcuda
OP
top fuel
|
OP
top fuel
Joined: Jan 2003
Posts: 1,811
North Dakota
|
Thanks everyone for the info. Sounds like it should work.
The only Carbs I care about are under the hood!
|
|
|
Re: ATI Damper Pulley Alignment?
[Re: BSB67]
#2691149
08/25/19 10:18 AM
08/25/19 10:18 AM
|
Joined: Feb 2014
Posts: 1,713 central il.
second 70
top fuel
|
top fuel
Joined: Feb 2014
Posts: 1,713
central il.
|
.060 is less than 1/16" I bet the factory wasn't that precise. And it's with an aftermarket WP housing and pump. WP to block and WP housing to WP gaskets are 0.030". At the end of the day, I would say it lines up as best as one could expect considering the stack/variables. Heck better than that yours look perfect.
|
|
|
Re: ATI Damper Pulley Alignment?
[Re: second 70]
#2692749
08/29/19 10:18 PM
08/29/19 10:18 PM
|
Joined: Jan 2003
Posts: 1,811 North Dakota
Azzkikrcuda
OP
top fuel
|
OP
top fuel
Joined: Jan 2003
Posts: 1,811
North Dakota
|
Got the ATI Damper today and measured pulley location against a stock damper. Was only 0.03 inch difference. Using Stock pulley setups with this Damper should not be a problem.
The only Carbs I care about are under the hood!
|
|
|
|
|