Re: Cam for 505 stroker
[Re: General 68]
#2670221
06/26/19 02:01 PM
06/26/19 02:01 PM
|
Joined: May 2008
Posts: 5,399 Aurora, Colorado
451Mopar
master
|
master
Joined: May 2008
Posts: 5,399
Aurora, Colorado
|
I'm running the 23-712-9 Comp Cams Hydraulic roller cam, XR286HR10 in my 505 engine. It is 236/242 duration @ 0.050 and drives fine doing 50 MPH @ 1,500 RPM in 5th gear (Legend Gear & Transmission 700 transmission.) Engine is about 10.3:1 compression, Mild ported stealth heads, 17cc dished pistons, 1-7/8" TTI headers with 2.5" dual exhaust with X-Pipe. Originally a Performer RPM intake, but now Edelbrock XT EFI intake and FAST 2.0 EFI controller.
|
|
|
Re: Cam for 505 stroker
[Re: 451Mopar]
#2670282
06/26/19 04:04 PM
06/26/19 04:04 PM
|
Joined: Aug 2011
Posts: 2,871 Pattison Texas
CSK
master
|
master
Joined: Aug 2011
Posts: 2,871
Pattison Texas
|
This is the Hyd roller 1.6 rockers I have in my 512 Charger, 3.54 gear Overdrive trans with lock up converter, I can cruise at 1800 rpm smooth with no bucking. power brake friendly?? NO
Last edited by csk; 06/26/19 04:08 PM.
1968 Charger COLD A/C Hilborn EFI 512ci 9.7 compression, Stealth heads, 4.10 gear A518 ODtrans 4100lb,10.93 full street car trim 2020 T/A 392 Stock 11.79 @ 114.5
|
|
|
Re: Cam for 505 stroker
[Re: CSK]
#2670345
06/26/19 06:49 PM
06/26/19 06:49 PM
|
Joined: Jan 2007
Posts: 401 Norway
General 68
OP
mopar
|
OP
mopar
Joined: Jan 2007
Posts: 401
Norway
|
Thanks! Keep it coming😄 I just ordered the 232/236-110 Hughes cam. Quite exited to ser how it performs. This is a mild build, 505,cr 9,8:1, Stage 4 iron heads, Indy dual plane, 2" tti's, 3" x-pipe, Holley 850 dp. 4200 lb '68 Charger, Tko 600 5-speed, Dana/Moser 60. I have an opinion on how it will perform, but what are your opinion?
|
|
|
Re: Cam for 505 stroker
[Re: General 68]
#2670362
06/26/19 07:26 PM
06/26/19 07:26 PM
|
Joined: Aug 2011
Posts: 2,871 Pattison Texas
CSK
master
|
master
Joined: Aug 2011
Posts: 2,871
Pattison Texas
|
Thanks! Keep it coming😄 I just ordered the 232/236-110 Hughes cam. Quite exited to ser how it performs. This is a mild build, 505,cr 9,8:1, Stage 4 iron heads, Indy dual plane, 2" tti's, 3" x-pipe, Holley 850 dp. 4200 lb '68 Charger, Tko 600 5-speed, Dana/Moser 60. I have an opinion on how it will perform, but what are your opinion? It will be a handful on the street, small cam for a 512
1968 Charger COLD A/C Hilborn EFI 512ci 9.7 compression, Stealth heads, 4.10 gear A518 ODtrans 4100lb,10.93 full street car trim 2020 T/A 392 Stock 11.79 @ 114.5
|
|
|
Re: Cam for 505 stroker
[Re: General 68]
#2670757
06/27/19 03:42 PM
06/27/19 03:42 PM
|
Joined: Feb 2003
Posts: 1,142 Tucson, AZ
cruzin
super stock
|
super stock
Joined: Feb 2003
Posts: 1,142
Tucson, AZ
|
I've been running a Hughes HE3844BL in a street-strip 400/470 E-Body, 4 spd. for 15 years. Here's the link to the cam's profile ( http://www.hughesengines.com/TechArticles/heseriescamprofilesbigblockhydraulic.php) if you like to compare with the Hughes cams you're considering. My motor has slightly more compression, E-heads, 1.6 rockers, Performer Plus intake, 1-7/8 headers with 3" exhaust, 4:10 or 3:55 gears, 3600 lbs. w/o driver, manual brakes. Low end torque is outstanding. I can lug the motor down and she pulls strong and easily to 6k. At the time, Hughes spec out the 3844 and the HE4449BL since I wanted to go with a hyd. flat tappet. With the added cubes you have, I believe you will be more than happy with the 3236.
|
|
|
Re: Cam for 505 stroker
[Re: General 68]
#2670781
06/27/19 04:44 PM
06/27/19 04:44 PM
|
Joined: Jan 2003
Posts: 31,071 Oregon
AndyF
I Win
|
I Win
Joined: Jan 2003
Posts: 31,071
Oregon
|
Thanks! Keep it coming😄 I just ordered the 232/236-110 Hughes cam. Quite exited to ser how it performs. This is a mild build, 505,cr 9,8:1, Stage 4 iron heads, Indy dual plane, 2" tti's, 3" x-pipe, Holley 850 dp. 4200 lb '68 Charger, Tko 600 5-speed, Dana/Moser 60. I have an opinion on how it will perform, but what are your opinion? It should have a fairly smooth idle and a ton of torque down low. It will most likely run out of air by 5500 rpm but you'll be going so fast at that point that you won't care. A street car doesn't need a race cam even though a lot of people want to put race cams in street cars.
|
|
|
Re: Cam for 505 stroker
[Re: AndyF]
#2683789
08/02/19 06:19 PM
08/02/19 06:19 PM
|
Joined: Jan 2007
Posts: 401 Norway
General 68
OP
mopar
|
OP
mopar
Joined: Jan 2007
Posts: 401
Norway
|
Well guys, I got the answers now🤣 Got the engine together and put in the Charger just in time to reach Orsa Dragfest in Sweden. Broke in the cam the night before we went and everything was good. Went 8.23/88.5 in the 1/8 mile. 4300lbs with med in. No prep track, Hoosier Quicktime Pro's, 28/12..5/15. Manual trans. Good vacuumn for power brakes. Engine pulled super strong. No change hooking - actually blew the tires loose when dropping the clutch at 2000 rpm. Quite scary - easy to over rew as it would fly past 6000 rpm in no time. Never got the 60' under 1,88 seconds. Broke the tires loose a bit when shifting to 2. gear. Pulled strong all the way to 6k. Won the bracket race (Had some luck😄) Idles nice and smooth at 1000 rpm. I only got time for a short test drive on travel road. Touching the go- pedal at 2000 rpm in 3rd gear would send the car sideways down the road. So far I am happy with the combo, but some carb- and chassis tuning might take it to the next level.
Last edited by General 68; 08/03/19 04:11 AM.
|
|
|
Re: Cam for 505 stroker
[Re: General 68]
#2921317
05/11/21 07:09 PM
05/11/21 07:09 PM
|
Joined: Mar 2005
Posts: 3,024 NY
B1duster
master
|
master
Joined: Mar 2005
Posts: 3,024
NY
|
Thanks! Keep it coming😄 I just ordered the 232/236-110 Hughes cam. Quite exited to ser how it performs. This is a mild build, 505,cr 9,8:1, Stage 4 iron heads, Indy dual plane, 2" tti's, 3" x-pipe, Holley 850 dp. 4200 lb '68 Charger, Tko 600 5-speed, Dana/Moser 60. I have an opinion on how it will perform, but what are your opinion? What octane fuel do you use ?
|
|
|
|
|