Re: What Valves for RHS LA X Heads?
[Re: Baxter61]
#2278492
03/29/17 08:01 PM
03/29/17 08:01 PM
|
Joined: Mar 2008
Posts: 860 lancaster,california
johnnycuda
super stock
|
super stock
Joined: Mar 2008
Posts: 860
lancaster,california
|
I bought my heads from Brian at IMM in Indio, Ca., they're 2.02"/1.60", beehive, not sure of installed height, metric valve stem I believe.
1970 'Cuda,Lime Light,499 Indy S/R's 10.70's @125,street driven ALOT! 1966 Barracuda 360,now a 5spd,Hemi Orange,Hot Rod Air, New daily driver-2003 Ram 2500 Cummins 5.9 '69 Valiant 2-dr, sleeper! New project---1938 Dodge truck, plan is a 360 with a A500, AC, Calvert rear susp., rack and pinion front with coils.
|
|
|
Re: What Valves for RHS LA X Heads?
[Re: Baxter61]
#2279147
03/30/17 10:06 PM
03/30/17 10:06 PM
|
Joined: Aug 2007
Posts: 498 El Dorado Ca
65signet
mopar
|
mopar
Joined: Aug 2007
Posts: 498
El Dorado Ca
|
They are a 8mm stem or 5/16 stem, ferrea makes the valves, and comp makes a 1.81 installed height beehive spring, for a standard valve spring pocket, i run them on stock 318 heads.
1965 Plymouth Barracuda 273 M/SA 1970 Plymouth Duster 360/904 10.60s with J heads
|
|
|
Re: What Valves for RHS LA X Heads?
[Re: 65signet]
#2279420
03/31/17 10:38 AM
03/31/17 10:38 AM
|
Joined: Nov 2004
Posts: 3,544 Syracuse,NY
CompWedgeEngines
master
|
master
Joined: Nov 2004
Posts: 3,544
Syracuse,NY
|
Great little heads, but set up is a bit of a pain. Easiest thing to do is ream them to 11/32, and use common SBC valves, much more options. If you want to stick with 5/16, less options, or at least they are more expensive options.
RIP Monte Smith
Your work is a reflection of yourself, autograph it with quality.
WD for Diamond Pistons,Sidewinder cylinder heads, Wiseco, K1 rods and cranks,BAM lifters, Morel lifters, Molnar Technologies, Harland Sharp, Pro Gear, Cometic, King Engine Bearings and many others.
|
|
|
Re: What Valves for RHS LA X Heads?
[Re: 65signet]
#2279510
03/31/17 12:48 PM
03/31/17 12:48 PM
|
Joined: Aug 2003
Posts: 3,245 Between a rock & a hard place
cudadoug
master
|
master
Joined: Aug 2003
Posts: 3,245
Between a rock & a hard place
|
They are a 8mm stem or 5/16 stem, ferrea makes the valves, and comp makes a 1.81 installed height beehive spring, for a standard valve spring pocket, i run them on stock 318 heads. Yes, what 65signet said. I have used the same valve and a Comp 26995 spring at 1.81" IH on both an Indy RHS head and an EQ head.
Last edited by cudadoug; 03/31/17 12:49 PM.
|
|
|
Re: What Valves for RHS LA X Heads?
[Re: Baxter61]
#2279672
03/31/17 04:35 PM
03/31/17 04:35 PM
|
Joined: Jan 2005
Posts: 12,419 Kalispell Mt.
HotRodDave
I Live Here
|
I Live Here
Joined: Jan 2005
Posts: 12,419
Kalispell Mt.
|
How much lift are you after? I am running stock length stainless valves 2.02 1.65 from hughes with their springs and retainers at .575 lift (theoretical) and it still clears the stock guide to boot.
As for diameter I would not go any bigger because the valves are so close but maybe you could go with a 2.05 1.60 or something but you need to open the bowl and chamber quite a bit as well as your bore should probably be bigger than my 4.04 to make any use of that. I would just run the 2.02 and open the chamber to the edge of your bore.
I am not causing global warming, I am just trying to hold off a impending Ice Age!
|
|
|
Re: What Valves for RHS LA X Heads?
[Re: HotRodDave]
#2279678
03/31/17 04:42 PM
03/31/17 04:42 PM
|
Joined: Nov 2004
Posts: 2,495 Oregon City, OR
Baxter61
OP
top fuel
|
OP
top fuel
Joined: Nov 2004
Posts: 2,495
Oregon City, OR
|
How much lift are you after? I am running stock length stainless valves 2.02 1.65 from hughes with their springs and retainers at .575 lift (theoretical) and it still clears the stock guide to boot.
As for diameter I would not go any bigger because the valves are so close but maybe you could go with a 2.05 1.60 or something but you need to open the bowl and chamber quite a bit as well as your bore should probably be bigger than my 4.04 to make any use of that. I would just run the 2.02 and open the chamber to the edge of your bore. Thats pretty much the plan right now is to run them on a 4.04 bore. As for lift Ive mostly been looking at mid-.550-.590 lift cams. I just didnt know what the stock length for these heads was, if it matched a regular LA head or not.
|
|
|
|
|