|
Re: Lets Talk Break In Oil
[Re: RapidRobert]
#2124594
08/04/16 01:24 AM
08/04/16 01:24 AM
|
Joined: Jun 2003
Posts: 52,972
Romeo MI
MR_P_BODY
OP
Master
|
OP
Master
Joined: Jun 2003
Posts: 52,972
Romeo MI
|
OT, I would confirm the lifters are free to rotate (Hughes "thunk" test) & the usual stuff that you are aware of more than I am, mixture/timing/immediate startup/goosing the throttle. They spin freely since I had to ream each one to fit and it will start with the EFI... I pre set the timing 36* before firing then check it... and I'll take it up to 2000 rpm and move it around some.... they all slide nicely... all at .0015 clearance EDIT plus these have the .012 EDM hole and light weight lifters 
Last edited by MR_P_BODY; 08/04/16 01:28 AM.
|
|
|
Re: Lets Talk Break In Oil
[Re: MR_P_BODY]
#2124598
08/04/16 01:38 AM
08/04/16 01:38 AM
|
Joined: Jul 2006
Posts: 4,319
Puyallup, WA
StealthWedge67
master
|
master
Joined: Jul 2006
Posts: 4,319
Puyallup, WA
|
I broke my solid flat tappet in with Joe Gibbs break in oil + Lucas Zinc additive. Also only on the outer valve springs of a double set. I regularly run Lucas Hot Rod 10w-30, with the same zinc additive. Change the oil once a year.
6 years, a few thousand street miles, and well over a hundred passes and I've had zero cam issues.
LemonWedge - Street heavy / Strip ready - 11.07 @ 120
|
|
|
Re: Lets Talk Break In Oil
[Re: MR_P_BODY]
#2124605
08/04/16 01:57 AM
08/04/16 01:57 AM
|
Joined: Feb 2011
Posts: 4,302
Nebraska
72Swinger
master
|
master
Joined: Feb 2011
Posts: 4,302
Nebraska
|
Depending on the cam lube used, another thing ive seen people do it put it on the sides of the lifters where they contact the lifter bores. BIG no no alot of that stuff is to ADD friction so the lifters do not slide on the cam lobes.
Mopar to the bone!!!
|
|
|
Re: Lets Talk Break In Oil
[Re: MR_P_BODY]
#2124661
08/04/16 08:46 AM
08/04/16 08:46 AM
|
Joined: Jul 2013
Posts: 561
USA
B3RE
mopar
|
mopar
Joined: Jul 2013
Posts: 561
USA
|
I don't have a flat tapped but used Lucas 30wt. Got a 2.5 gallon jug of it. Seemed like the rings seated on the first drive. This is just a cam change... engine has about 850 miles on it but the tight LSA didnt like the EFI or should I say it the other way around Mike, Why didn't you go with a wider LSA roller grind? I know there isn't much to choose from in the catalogs, but if I find one that suits the combination, but has a tight LSA, I'll call them and have one ground wider. Comp can usually turn one of these around in a couple weeks, and then the lobe failure worries go away. Just a thought, since you are already set up for a roller.
Mike Beachel
I didn't write the rules of math nor create the laws of physics, I am just bound by them.
|
|
|
Re: Lets Talk Break In Oil
[Re: B3RE]
#2124697
08/04/16 10:04 AM
08/04/16 10:04 AM
|
Joined: Jan 2003
Posts: 6,187
Melbourne , Australia
LA360
master
|
master
Joined: Jan 2003
Posts: 6,187
Melbourne , Australia
|
I used Lucas, it was more available than the Gibbs Driven. I've heard lots of good things about the Gibbs
Alan Jones
|
|
|
Re: Lets Talk Break In Oil
[Re: B3RE]
#2124705
08/04/16 10:13 AM
08/04/16 10:13 AM
|
Joined: Jun 2003
Posts: 52,972
Romeo MI
MR_P_BODY
OP
Master
|
OP
Master
Joined: Jun 2003
Posts: 52,972
Romeo MI
|
I don't have a flat tapped but used Lucas 30wt. Got a 2.5 gallon jug of it. Seemed like the rings seated on the first drive. This is just a cam change... engine has about 850 miles on it but the tight LSA didnt like the EFI or should I say it the other way around Mike, Why didn't you go with a wider LSA roller grind? I know there isn't much to choose from in the catalogs, but if I find one that suits the combination, but has a tight LSA, I'll call them and have one ground wider. Comp can usually turn one of these around in a couple weeks, and then the lobe failure worries go away. Just a thought, since you are already set up for a roller. I didnt like a few things on the Comp lifters.. the edm hole is .026.. too big when I got warm my oil pressure was lower than I like plus I PR oil... lots of built in losses.. the edm hole in the Hughes is .012
|
|
|
Re: Lets Talk Break In Oil
[Re: ksj]
#2124722
08/04/16 10:44 AM
08/04/16 10:44 AM
|
Joined: May 2014
Posts: 103
muskegon MI
v cummins
member
|
member
Joined: May 2014
Posts: 103
muskegon MI
|
Gibbs for break in and Valvoline VR1Racing oil after that This has worked well for me. All of my resto. hemi. max wedge. 440s. get this and works well. use the gibbs BR yellow lab. not the HR-2. then the Valvoline. I have also used a lot of rotella in the past
|
|
|
Re: Lets Talk Break In Oil
[Re: MR_P_BODY]
#2124942
08/04/16 03:01 PM
08/04/16 03:01 PM
|
Joined: Jan 2003
Posts: 6,531
Jacksonville, FL
Chris2581
master
|
master
Joined: Jan 2003
Posts: 6,531
Jacksonville, FL
|
I use the Chrysler cam lube,STP and Rotella,fire it and break in the engine.
Nautilus Racing-
We use Superformance gaskets and Turbo Action converters/products.
|
|
|
Re: Lets Talk Break In Oil
[Re: Eric]
#2125125
08/04/16 06:21 PM
08/04/16 06:21 PM
|
Joined: Oct 2011
Posts: 3,036
bean town ....Ca
WHITEDART
master
|
master
Joined: Oct 2011
Posts: 3,036
bean town ....Ca
|
The last couple flat tappet this is what I used with great results. I don't think it would hurt to run it all the time.. maybe lose a few horsepower but sure would be good for the cam
In the 8s N/A.with Brett miller W8's
5.07 at 133 at 2700lb
|
|
|
Re: Lets Talk Break In Oil
[Re: LA360]
#2125129
08/04/16 06:26 PM
08/04/16 06:26 PM
|
Joined: Jun 2003
Posts: 52,972
Romeo MI
MR_P_BODY
OP
Master
|
OP
Master
Joined: Jun 2003
Posts: 52,972
Romeo MI
|
I used Lucas, it was more available than the Gibbs Driven. I've heard lots of good things about the Gibbs I've been looking around what is out there local... I can get the Lucas break in oil local... I'll look some more to see if Gibbs is easy to get.... now ... with these break in oils do you add any more zinc... or is too much zinc bad thanks guys
|
|
|
Re: Lets Talk Break In Oil
[Re: BIGSTROKER]
#2125498
08/05/16 08:36 AM
08/05/16 08:36 AM
|
Joined: Jan 2003
Posts: 1,817
North Dakota
Azzkikrcuda
top fuel
|
top fuel
Joined: Jan 2003
Posts: 1,817
North Dakota
|
I use Comp Break-in oil on engines I do, No problems yet.
The only Carbs I care about are under the hood!
|
|
|
|
|
