made some progress today with the 13.5:1 410 build
#1941306
10/29/15 10:22 PM
10/29/15 10:22 PM
|
Joined: Jan 2007
Posts: 8,042 Mt Morris Michigan
mopar dave
OP
master
|
OP
master
Joined: Jan 2007
Posts: 8,042
Mt Morris Michigan
|
the bearing clearances ended up at .00325 on main and .002" on rods using coated rod bearings. crank end play is .0055" and rod side clearance is .025"-.027". pistons look to be .010" in the hole. the 1mm rings went in the bores easier than i thought they would as they didn't want to stay in their grooves. used wd40 on rings and torco assembly lube on bottom of skirts. the cam is being reground by Bullet and will be 267/275@50 .688/.688 lift on 106 per kurt@Bullet. it is a solid roller. so as of now i'm just waiting on cam and heads and then i will continue. goal is to have it done and on dyno by christmas. should make between 650 and 680hp.
Last edited by mopar dave; 10/29/15 10:24 PM.
|
|
|
Re: made some progress today with the 13.5:1 410 build
[Re: mopar dave]
#1941336
10/29/15 10:52 PM
10/29/15 10:52 PM
|
Joined: Sep 2014
Posts: 4,457 Washington
madscientist
master
|
master
Joined: Sep 2014
Posts: 4,457
Washington
|
Thin rings are where it's at.
Remind me about the heads/intake.
Just because you think it won't make it true. Horsepower is KING. To dispute this is stupid. C. Alston
|
|
|
Re: made some progress today with the 13.5:1 410 build
[Re: mopar dave]
#1941341
10/29/15 10:59 PM
10/29/15 10:59 PM
|
Joined: Jan 2003
Posts: 11,719 Portage,michigan
B3422W5
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 11,719
Portage,michigan
|
Sounds cool Dave. Would have figured the cam would be more in the mid 270's@50 range.
69 Dart GTS A4 Silver All steel, flat factory hood, 3360race weight 418 BPE factory replacement headed stroker, 565 lift solid cam Best so far, 10.40 @127 1/4 1.41 best 60 foot 6.60 at 103.90 1/8
|
|
|
Re: made some progress today with the 13.5:1 410 build
[Re: madscientist]
#1941349
10/29/15 11:13 PM
10/29/15 11:13 PM
|
Joined: Jan 2007
Posts: 8,042 Mt Morris Michigan
mopar dave
OP
master
|
OP
master
Joined: Jan 2007
Posts: 8,042
Mt Morris Michigan
|
indy heads 360-1 and indy intake ported. dwayne says heads now flow 20 more cfm at mid lift and should flow 330 range at .700 when he's done.
Last edited by mopar dave; 10/29/15 11:15 PM.
|
|
|
Re: made some progress today with the 13.5:1 410 build
[Re: mopar dave]
#1941522
10/30/15 05:04 AM
10/30/15 05:04 AM
|
Joined: Jan 2003
Posts: 11,719 Portage,michigan
B3422W5
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 11,719
Portage,michigan
|
My 4 inch was 273-280, Dwayne specced it with mild lobes so I could drive it around some. The new owner moved up to another Dwayne cam that was 276/284 with more aggressive lobes and the car really picked up. Same compression as your running. Most stuff I have seen in the mid 260's works good on edelbrock combo's.
69 Dart GTS A4 Silver All steel, flat factory hood, 3360race weight 418 BPE factory replacement headed stroker, 565 lift solid cam Best so far, 10.40 @127 1/4 1.41 best 60 foot 6.60 at 103.90 1/8
|
|
|
Re: made some progress today with the 13.5:1 410 build
[Re: B3422W5]
#1941600
10/30/15 11:57 AM
10/30/15 11:57 AM
|
Joined: Jan 2007
Posts: 8,042 Mt Morris Michigan
mopar dave
OP
master
|
OP
master
Joined: Jan 2007
Posts: 8,042
Mt Morris Michigan
|
267 isnt too far from 273. i was told it takes 10* change too tell any difference. i told them it would see some street driving, but mostly track. too small is better than too big any day.
Last edited by mopar dave; 10/30/15 11:58 AM.
|
|
|
Re: made some progress today with the 13.5:1 410 build
[Re: mopar dave]
#1941773
10/30/15 07:45 PM
10/30/15 07:45 PM
|
Joined: Oct 2009
Posts: 1,267 North, Alabama
D-50
pro stock
|
pro stock
Joined: Oct 2009
Posts: 1,267
North, Alabama
|
My 394 ci small block has a 255/266 .050 cam but is is only 10.9 compression. (Pump gas)
1.33 60 ft,6.21 at 110.59 in the 1/8, pump gas small block,2950lbs,drag radials,mufflers and driven to track ...
|
|
|
|
|