|
Radio condenser help
#1035756
07/19/11 05:24 AM
07/19/11 05:24 AM
|
Joined: Aug 2008
Posts: 242 midwest
intragration
OP
enthusiast
|
OP
enthusiast
Joined: Aug 2008
Posts: 242
midwest
|
Yes, I did a restoration, and yes, I have radio static ha ha. I did the research, and I see basically what I have to do. I'll start with the condenser on the coil, and I will also put one on the radio and see where that leaves me.
My two questions are, how do I wire it on the radio, just between the radio power lead and the radio case? Also, for you electronics guys, can you explain simply the concept behind how this works? Just curious, for my own knowledge. Thank you!
|
|
|
Re: Radio condenser help
[Re: intragration]
#1035757
07/19/11 06:33 AM
07/19/11 06:33 AM
|
Joined: Jun 2006
Posts: 344 PA
noplanb
enthusiast
|
enthusiast
Joined: Jun 2006
Posts: 344
PA
|
It should go between power and ground lead.
A condenser (capacitor) on a DC supply line acts as an AC filter, cleaning up the DC power by shunting AC (noise) to ground. It's like if you had water pressure issues from the city, and you put a big water tank between the city water supply and your house. The supply fills the tank, while the house draws water from the tank. You wouldn't see pressure changes in the line from the house.
A condenser is like a water tank.
Last edited by noplanb; 07/19/11 06:54 AM.
remember when you said honey, some day that car is gonna look so good in front of our house
|
|
|
Re: Radio condenser help
[Re: noplanb]
#1035758
07/19/11 07:32 AM
07/19/11 07:32 AM
|
Joined: Aug 2003
Posts: 12,291 Kent, Wa
340SHORTY
Truck Nut
|
Truck Nut
Joined: Aug 2003
Posts: 12,291
Kent, Wa
|
are you running non resistor plugs or solid core sparkplug wires???
I am truckless..
|
|
|
Re: Radio condenser help
[Re: intragration]
#1035760
07/19/11 06:40 PM
07/19/11 06:40 PM
|
Joined: Jun 2008
Posts: 1,822 Colorado
denfireguy
top fuel
|
top fuel
Joined: Jun 2008
Posts: 1,822
Colorado
|
Quote:
Thank you for the detailed answer.
I don't know exactly what kind of plugs or wires I have. The thing is, I have no capacitors installed, not even on the coil. This is an easy step and should take the noise down to a level that's acceptable to me.
If you are running a solid state ignition either stock or add on, capacitors are not going to be much help. They were required on distributors with points. The arcing of the points generated a lot of noise. The first place to filter ignition noise is with resistive plug wires and resistive plugs. The plug works a spark gap transmitter and the plug wires act as the antenna. Distributed resistance lowers the radiation. I would look there first and also for any unintended high voltage arcing under the hood from a cracked distributor cap, knicked wire or other gap. Looking under the hood with the engine running in the dark will reveal any issues like that. Craig
2014 Ram 1500 Laramie, 73 Cuda Previous mopars: 62 Valiant, 65 Fury III, 68 Fury III, 72 Satellite, 74 Satellite, 89 Acclaim, 98 Caravan, 2003 Durango Only previous Non-Mopar: Schwinn Tornado
|
|
|
|
|
|