will it be absolutely necessary to mill the heads?

Print Thread

Re: will it be be absolutely necessary to mill the heads? [Re: JohnRR] #1173186 02/17/12 09:52 AM 02/17/12 09:52 AM
Joined: Nov 2004 Posts: 340 Vitoria, Spain C Coke OP enthusiast
Coke OP enthusiast C Joined: Nov 2004 Posts: 340 Vitoria, Spain	I have measured the block height and there are 270mm (10.6299") between the crankshaft center and the block surface. I have read around here that a 440 block uses to have 10.725" so i suppouse that it has been decked. Uploaded with ImageShack.us About the rod lenght i have meassured 180mm(7.086") from the center of the pin to the big end center,or the surface were it meets the bearing cap. This is what i don,t understand cause the workshop manual says that the are 6.766" to 6.770"??? The rod "I" beam has the number #1851535 stamped on it. Thanks i advance for any input. Uploaded with ImageShack.us Last edited by Coke; 02/17/12 11:48 AM.

Entire Thread
Subject	Posted By	Posted
will it be absolutely necessary to mill the heads?	Coke	02/06/12 01:01 PM
Re: will it be be absolutely necessary to mill the heads?	JohnRR	02/06/12 01:23 PM
Re: will it be be absolutely necessary to mill the heads?	bobs66440	02/06/12 01:26 PM
Re: will it be be absolutely necessary to mill the heads?	DaytonaTurbo	02/06/12 08:40 PM
Re: will it be be absolutely necessary to mill the heads?	Twostick	02/06/12 10:21 PM
Re: will it be be absolutely necessary to mill the heads?	dogdays	02/07/12 12:37 AM
Re: will it be be absolutely necessary to mill the heads?	Coke	02/07/12 12:52 PM
Re: will it be be absolutely necessary to mill the heads?	bobs66440	02/07/12 02:49 PM
Re: will it be be absolutely necessary to mill the heads?	JohnRR	02/07/12 03:29 PM
Re: will it be be absolutely necessary to mill the heads?	Coke	02/09/12 12:28 PM
Re: will it be be absolutely necessary to mill the heads?	JohnRR	02/09/12 02:48 PM
Re: will it be be absolutely necessary to mill the heads?	383man	02/09/12 07:01 PM
Re: will it be be absolutely necessary to mill the heads?	Coke	02/10/12 12:12 AM
Re: will it be be absolutely necessary to mill the heads?	Stanton	02/17/12 06:04 PM
Re: will it be be absolutely necessary to mill the heads?	RapidRobert	02/06/12 03:35 PM
Re: will it be be absolutely necessary to mill the heads?	dogdays	02/06/12 05:42 PM
Re: will it be be absolutely necessary to mill the heads?	JohnRR	02/06/12 05:49 PM
Re: will it be be absolutely necessary to mill the heads?	dogdays	02/06/12 07:31 PM
Re: will it be be absolutely necessary to mill the heads?	JohnRR	02/06/12 07:53 PM
Re: will it be be absolutely necessary to mill the heads?	BSB67	02/07/12 01:58 AM
Re: will it be be absolutely necessary to mill the heads?	JohnRR	02/07/12 06:12 AM
Re: will it be be absolutely necessary to mill the heads?	BSB67	02/07/12 12:33 PM
Re: will it be be absolutely necessary to mill the heads?	Mr.Yuck	02/10/12 01:35 AM
Re: will it be be absolutely necessary to mill the heads?	JohnRR	02/10/12 01:53 AM
Re: will it be be absolutely necessary to mill the heads?	RodStRace	02/10/12 02:43 AM
Re: will it be be absolutely necessary to mill the heads?	dogdays	02/10/12 01:45 AM
Re: will it be be absolutely necessary to mill the heads?	Coke	02/10/12 10:32 PM
Re: will it be be absolutely necessary to mill the heads?	Coke	02/15/12 09:48 PM
Re: will it be be absolutely necessary to mill the heads?	JohnRR	02/15/12 10:53 PM
Re: will it be be absolutely necessary to mill the heads?	Coke	02/16/12 10:25 PM
Re: will it be be absolutely necessary to mill the heads?	Coke	02/17/12 01:52 PM
Re: will it be be absolutely necessary to mill the heads?	JohnRR	02/17/12 04:37 PM
Re: will it be be absolutely necessary to mill the heads?	Coke	02/17/12 10:05 PM
Re: will it be be absolutely necessary to mill the heads?	JohnRR	02/18/12 02:04 PM
Re: will it be be absolutely necessary to mill the heads?	OzHemi	02/17/12 10:09 PM
Re: will it be be absolutely necessary to mill the heads?	Stanton	02/17/12 11:02 PM
Re: will it be be absolutely necessary to mill the heads?	Coke	02/18/12 12:46 AM
Re: will it be be absolutely necessary to mill the heads?	Stanton	02/18/12 02:15 AM
Re: will it be be absolutely necessary to mill the head	dogdays	02/18/12 04:36 AM
Re: will it be be absolutely necessary to mill the head	JohnRR	02/18/12 02:07 PM
Re: will it be be absolutely necessary to mill the head	dogdays	02/18/12 10:41 PM
Re: will it be be absolutely necessary to mill the head	dogdays	02/18/12 11:24 PM
Re: will it be be absolutely necessary to mill the head	Coke	02/18/12 11:42 PM
Re: will it be absolutely necessary to mill the heads?	Dodgem	02/18/12 06:14 PM
Re: will it be absolutely necessary to mill the heads?	Stanton	02/18/12 07:35 PM

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To