Re: Best motor mounts for stroker
[Re: joewhite440]
#906535
01/17/11 12:41 AM
01/17/11 12:41 AM
|
Joined: Jan 2006
Posts: 587
IL . usa
cjs69mope
mopar
|
mopar
Joined: Jan 2006
Posts: 587
IL . usa
|
I run a morroso steel mount on the drivers side with a big 5/8 inch bolt/thead size bolt through the big hole in the k frame . i got the bolt at ace hard ware for a couple of bucks . the bolt is the best way to keep the engine from moving , because it will shift with stock bolt. just run a stock rubber mount on passinger side and a poly trans mount . This works great some vibration but not bad i drive the car all summer like this and i dont mind the extra vibration . your friends will think the car is even more bad a$$ then it is because it make the car feel faster . my set up is almost the same as yours 493 hemi 4sp 410 gear 69 charger with 70 pistol grip conslole shifter . Hope this helps Cj 
1969 Dodge Charger
1969 Dodge Superbee
|
|
|
Re: Best motor mounts for stroker
[Re: pressureangle]
#906537
01/17/11 08:51 AM
01/17/11 08:51 AM
|
Joined: Jan 2003
Posts: 21,071
Niles , Ohio
therocks
oh wait.but hey.lets see.oh yeah.
|
oh wait.but hey.lets see.oh yeah.
Joined: Jan 2003
Posts: 21,071
Niles , Ohio
|
My 65 with 440 4 speed would tear the cheap rubbers in a short while.I used Imperial Services poly mounts.My kid has them in his 62 300 also.His have been in at least 7 years mine 5 years.No problems and not much vibration.Rocky
Chrysler Firepower
|
|
|
Re: Best motor mounts for stroker
[Re: therocks]
#906538
01/17/11 03:50 PM
01/17/11 03:50 PM
|
Joined: Sep 2003
Posts: 2,966
Wendy, I'm home.
dstryr
master
|
master
Joined: Sep 2003
Posts: 2,966
Wendy, I'm home.
|
Motor Mounts The dodgecharger.com link was going to the home page so I posted again; let's see if it works. I used the same 2-bolts through the mount. Started with hex bolts and ended up with a countersunk metric bolts and nylocks because I could not find a countersunk grade 8 anywhere, online, hardware stores, fastenal, etc. I have what's leftover from a box of 25 if anyone wants a pair.
dstryr, since 1986.
|
|
|
Re: Best motor mounts for stroker
[Re: cjs69mope]
#906539
01/17/11 04:53 PM
01/17/11 04:53 PM
|
Joined: Jan 2003
Posts: 2,402
Wichita,KS
Blakcharger440
top fuel
|
top fuel
Joined: Jan 2003
Posts: 2,402
Wichita,KS
|
Quote:
I run a morroso steel mount on the drivers side with a big 5/8 inch
bolt/thead size bolt through the big hole in the k frame .
i got the bolt at ace hard ware for a couple of bucks .
the bolt is the best way to keep the engine from moving , because it will shift with stock bolt.
just run a stock rubber mount on passinger side and a poly trans mount .
This works great some vibration but not bad i drive the car all summer like this and i dont mind the extra vibration .
your friends will think the car is even more bad a$$ then it is because it make the car feel faster .
my set up is almost the same as yours 493 hemi 4sp 410 gear 69 charger with 70 pistol grip conslole shifter .
Hope this helps Cj
I run almost the same setup minus the poly trans Mount. Mine is 70 Charger RT with 512RB and 4spd. Has some vibration but I think it is fine for the street.
I did have solid mounts on both sides but it was too much vibration for summer cruising.
|
|
|
Re: Best motor mounts for stroker
[Re: AndyF]
#906540
01/17/11 05:00 PM
01/17/11 05:00 PM
|
Joined: Jan 2007
Posts: 780
Woodinville, WA
Viol8r
super stock
|
super stock
Joined: Jan 2007
Posts: 780
Woodinville, WA
|
Quote:
Get the poly ones from Schumacher
These feel like solid and you will hear it in the car. Trust me I had them on the car for an hour and took them off. Not sure if this is a race application, if not use the Magnum mounts from Mancini. They are between stock and poly. They have a lock out on them.
|
|
|
Re: Best motor mounts for stroker
[Re: challengermike]
#906544
01/17/11 09:52 PM
01/17/11 09:52 PM
|
Joined: Jul 2003
Posts: 6,342
SE PA.
QuickBpBp
master
|
master
Joined: Jul 2003
Posts: 6,342
SE PA.
|
Quote:
I use a solid on the drivers side and stock one on the pass side and trans,no vibration at all.But i would guess if you had a engine that wasnt balanced real well you would feel it.
 This is my normal response EVERY time this question comes up. It will never break and the stock side doesn't make it have any vibrations. Cheap and easy... 
|
|
|
Re: Best motor mounts for stroker
[Re: challengermike]
#906545
01/17/11 09:58 PM
01/17/11 09:58 PM
|
Joined: Nov 2007
Posts: 21,822
Kirkland, Washington
Pacnorthcuda
Too Many Posts
|
Too Many Posts
Joined: Nov 2007
Posts: 21,822
Kirkland, Washington
|
Polylock on drivers side, Stock on passenger. I too tried the polys on both sides for about an hour. BUZZ city. Replaced the pass with stock and eliminated 90% of the vibration. Schumacher doesn;t sell them individually (wonder why???  ) If your interested I'll sell you my extra for my cost ($80 shipped to your door.) 440 biscuit style. PM if interested.
|
|
|
|
|
