|
Piston Selection
#630111
03/03/10 10:22 PM
03/03/10 10:22 PM
|
Joined: Feb 2010
Posts: 34 Salinas, CA USA!
BuBbABFP
OP
member
|
OP
member
Joined: Feb 2010
Posts: 34
Salinas, CA USA!
|
Hey all, about a month ago I purchased a complete 440, from intake to pan its a 77 block. It came with a Performer 440 and a 750 eddy. Well I took the heads off and took it to my local machine shop and the previous owner had changed the pistons but left it same bore. Cylinder walls look ok but you can feel the wear on the top where the ring goes up to.
So the owner told me I can run it the way it is or just spend a few more dollars and get it freshened up and get my desired CR. So here is what I am working with. Looking for about 9.5:1 -10:1 CR.
1977 440 Block will be .30 over stock crank(has forged damper but not sure if crank is) 906 heads that have been ported and polished multi angle valve job, hardened seats and cut to 82cc with .575 max lift on springs. Cam (Not sure, but I want to take the most advantage of heads and CR) Pistons( Need to know which would be the best for my Application, I am not looking to go forged but I was looking at the KB237's) Carb ( I am thinking of a Holley Double Pumper 800-850CFM intake- I will be running a Holley Street Dominator head gaskets ( Not sure, I need help with this too)
I also have a Melling High Volume oil pump, Holley red electric fuel pump. As for rockers, can I use stockers? i don't want to spend 500$ on harland sharp or comp magnums. I saw the Crane golds at a good price over at summit but do I need to buy new shafts and all? Stock push rods a swell? Feel free to change things up, give me all the input you got. Thx! guys!
Roy.
1968 Dodge Charger
|
|
|
Re: Piston Selection
[Re: BuBbABFP]
#630112
03/03/10 10:55 PM
03/03/10 10:55 PM
|
Joined: Nov 2003
Posts: 36,041 Lincoln Nebraska
RapidRobert
Circle Track
|
Circle Track
Joined: Nov 2003
Posts: 36,041
Lincoln Nebraska
|
I would mill the open chamber recesses to equalize them (the depth/slope can vary) along w some quench pad KB's to get .040" quench along w your desired CR which will in all likelyhood let your get by w 93 pump gas
live every 24 hour block of time like it's your last day on earth
|
|
|
Re: Piston Selection
[Re: BuBbABFP]
#630113
03/04/10 12:52 AM
03/04/10 12:52 AM
|
Joined: Jan 2003
Posts: 27,421 Balt. Md
383man
Too Many Posts
|
Too Many Posts
Joined: Jan 2003
Posts: 27,421
Balt. Md
|
Quote:
Hey all, about a month ago I purchased a complete 440, from intake to pan its a 77 block. It came with a Performer 440 and a 750 eddy. Well I took the heads off and took it to my local machine shop and the previous owner had changed the pistons but left it same bore. Cylinder walls look ok but you can feel the wear on the top where the ring goes up to.
So the owner told me I can run it the way it is or just spend a few more dollars and get it freshened up and get my desired CR. So here is what I am working with. Looking for about 9.5:1 -10:1 CR.
1977 440 Block will be .30 over stock crank(has forged damper but not sure if crank is) 906 heads that have been ported and polished multi angle valve job, hardened seats and cut to 82cc with .575 max lift on springs. Cam (Not sure, but I want to take the most advantage of heads and CR) Pistons( Need to know which would be the best for my Application, I am not looking to go forged but I was looking at the KB237's) Carb ( I am thinking of a Holley Double Pumper 800-850CFM intake- I will be running a Holley Street Dominator head gaskets ( Not sure, I need help with this too)
I also have a Melling High Volume oil pump, Holley red electric fuel pump. As for rockers, can I use stockers? i don't want to spend 500$ on harland sharp or comp magnums. I saw the Crane golds at a good price over at summit but do I need to buy new shafts and all? Stock push rods a swell? Feel free to change things up, give me all the input you got. Thx! guys!
Roy.
Your build will be almost the same as my 440. I have a .030 over 440 with stock crank and rods. KB quench pad pistons that I set at .042 quench with my 906 heads I ported. It comes out to 10.0 comp and it runs fine on 92 pump with 38 total timing. It has the MP .557 cam and I use Isky ductile iron adjustable rockers. I also run the Holley Street Dominator with an 850 DP. I have the Holley red pump back by the tank and thats the only pump I use. It runs mid 11's in my 3700 lb 63 Sport Fury with a best of 11.49. Sounds like a nice solid combo. Ron
|
|
|
Re: Piston Selection
[Re: 383man]
#630114
03/04/10 10:28 PM
03/04/10 10:28 PM
|
Joined: Feb 2010
Posts: 34 Salinas, CA USA!
BuBbABFP
OP
member
|
OP
member
Joined: Feb 2010
Posts: 34
Salinas, CA USA!
|
Hey guys thanks for the reply's! 383man, thanks much for sharing your combo. sounds like awesome running 440. Anyways If you can give me your suggestions because I am a complete Noob when it comes to building an engine, this is going to be my very first tear down of an engine. I have done a Heads and Cam upgrade on an LS1 but that about it. So I am trying to get the correct parts before I order. So so far I have these Rings and Pistons. http://www.summitracing.com/parts/UEM-KB237KTM030/What about rod bolts? Should I upgrade to ARP's? I have found these. http://www.summitracing.com/parts/ARP-145-6002/What about head gasket? I bought a complete 440 felpro gasket kit off summit for 55 bucks it comes with head gasket but not sure if they will be correct for my setup. As for push rods would you recommend me to upgrade or should I use same ones? I would really appreciate the help from you or any one else! Thx, Roy.
1968 Dodge Charger
|
|
|
Re: Piston Selection
[Re: ahy]
#630117
03/06/10 01:38 AM
03/06/10 01:38 AM
|
Joined: Feb 2010
Posts: 34 Salinas, CA USA!
BuBbABFP
OP
member
|
OP
member
Joined: Feb 2010
Posts: 34
Salinas, CA USA!
|
Right now I have stock rockers, but I think I will purchase some isky iron adjustables if I can find some or I will save up for some crane golds. I do have the felpro 8519PTI gasket 4.450 bore and .038 thickness. So If I get the block close to .003 deck clearance to achieve .040 quesnch with the kb237 I should be at around 10.2:1 CR with the 82cc heads correct?
1968 Dodge Charger
|
|
|
|
|
|