Re: Source heads
[Re: migsBIG]
#509625
10/28/09 09:13 AM
10/28/09 09:13 AM
|
Joined: Jan 2003
Posts: 2,933 Finalnd, Perkele
jyrki
master
|
master
Joined: Jan 2003
Posts: 2,933
Finalnd, Perkele
|
Depends of what you want. Flow is one thing, crossectional area is another. If you have cubes and you want power, you'll need a proper port size. The CNC 440source head is very good for a big high torq engine, but the port size will hold it back at higher rpm.
Plynouth VIP '67 TT IC EFI
|
|
|
Re: Source heads
[Re: WannaRunner]
#509631
10/29/09 03:10 AM
10/29/09 03:10 AM
|
Joined: Feb 2003
Posts: 21,318 Manitoba, Canada
DaytonaTurbo
Too Many Posts
|
Too Many Posts
Joined: Feb 2003
Posts: 21,318
Manitoba, Canada
|
Quote:
Is everything in the stock location with the Eddies?
~thanks
Yes.
FWIW I had zero problems with my source heads out of the box and I've been daily driving them. Plus the CNC'd source heads are done by modern cylinder head so they do get looked over again before you get them.
|
|
|
Re: Source heads
[Re: DaytonaTurbo]
#509632
10/29/09 03:48 AM
10/29/09 03:48 AM
|
Joined: Jan 2008
Posts: 299 Fitchbug, Mass.
WannaRunner
OP
enthusiast
|
OP
enthusiast
Joined: Jan 2008
Posts: 299
Fitchbug, Mass.
|
Quote:
Quote:
Is everything in the stock location with the Eddies?
~thanks
Yes.
FWIW I had zero problems with my source heads out of the box and I've been daily driving them. Plus the CNC'd source heads are done by modern cylinder head so they do get looked over again before you get them.
Thanks!
|
|
|
Re: Source heads
[Re: DaytonaTurbo]
#509633
10/29/09 08:08 AM
10/29/09 08:08 AM
|
Joined: Jan 2003
Posts: 3,575 The Netherlands
BigBlockMopar
master
|
master
Joined: Jan 2003
Posts: 3,575
The Netherlands
|
Quote:
Quote:
Is everything in the stock location with the Eddies?
~thanks
Yes. ...
Did Edelbrock change the sparkplug angles back to stock angles at one time?
I thought only the Mopar Performance heads made by Edelbrock had at least the sparkplugs at 90 degrees to the head again.
|
|
|
Re: Source heads
[Re: BigBlockMopar]
#509634
10/29/09 08:50 AM
10/29/09 08:50 AM
|
Joined: Jan 2003
Posts: 21,083 Niles , Ohio
therocks
oh wait.but hey.lets see.oh yeah.
|
oh wait.but hey.lets see.oh yeah.
Joined: Jan 2003
Posts: 21,083
Niles , Ohio
|
E heads use angle plugs.I also have the Sourve heads and have about 400 into new spreings retainers keepers.Id of had to change them on the E heads also.I have over 2 years on my heads street and strip.No problems at all.Mine are the first ones.If they had had the CNC ones I would have bought them.Rocky
Chrysler Firepower
|
|
|
Re: Source heads
[Re: Stanton]
#509636
10/29/09 07:14 PM
10/29/09 07:14 PM
|
Joined: Jan 2008
Posts: 299 Fitchbug, Mass.
WannaRunner
OP
enthusiast
|
OP
enthusiast
Joined: Jan 2008
Posts: 299
Fitchbug, Mass.
|
Quote:
I ran the numbers for the ported Source heads on desktop dyno and they made more torque and HP than ez1 heads. This was with a mild solid roller and with the 512 and 528 configuration. However, they are at their limit at that point so if you want more power in the future then you have to go with a different head.
For what you're doing I'd go with the 512 and the ported Source heads. They don't need any special rockers, etc.
Thanks for your effort! the 512 is about where I am hovering, anything more and the RR will be on skates.....
|
|
|
|
|