Pete Jackson Noisy Gear Drive – less than 500 miles $75
Big block water pump housing powder coated $50
Big block timing cover powder coated $25
Big block timing cover chrome $15
Factory chrome valve covers $35
Proform or similar chrome valve covers $20
Taylor spiro-pro plug wires big block Mopar $40
Miscellaneous Jegs hose and fittings $50
Mopar performance electronic distributor $80
Mancini Big Block Balancer MRE80013 – new $90 - SOLD

Parts located in Ripley, WV
Price doesnt include shipping

70 B-body voltage regulator mounting bracket. $15

New chrome coil cover & coil mounting bracket. $20

New factory type big block spark plug wire separator kit. Some surface rust from humidity on a couple of them. $50

NOS big block heat riser kit #3420046. $225

Two new, unused big block head pipe to exhaust manifold flanges still in the packages. $15 for the pair.

Unused/unopened big block exhaust manifold stud kit. Although the bag is unopened, I can see some surface rust from humidity on some of the pieces. $40

NOS Cal Custom chrome radiator cap. $20

NOS Cal Custom chrome battery hold down. $25

Four new extra wide chrome valve cover hold down clamps. $10 for the set

NOS Cal Custom polished big block valve covers. $450

New exhaust manifold heat stove to air cleaner hose. $20

NOS fan clutch 3769614 for 1974 all V-8 engines. $100

New big block chrome valley pan hold down rails & bolts. $30

Gauge type oil pressure sending unit. $20

Vintage Cal Custom 14" finned aluminum air cleaner with filter. $100

1970 Single nipple oil breather with hose. $30

New Mopar Performance chrome big block distributor hold down. $20

New 12" long oval 4 barrel aluminum air cleaner with filter. It measures 12" L x 8 1/4" W x 3" H and has a 5 1/8" carb opening. $55

New Mopar Performance chrome water neck. Was bolted on an engine but then taken back off before the engine was ran. $10

NOS Direct Connection big block double roller timing chain #P4120264. $75

New Mr. Gasket chrome oil filter cover. $15

133 New radiator, heater hose and fuel hose clamp covers. Some chrome, some red anodized and some blue anodized. Various sizes. $75 for the lot.

MP big block high volume oil pump P4286590. This was new when I tried it on my motor but it was too much pressure so I switched to a stock pump. $80

9 Chrome t-handle valve cover bolts. $10

Factory starter, part/casting #3755259. This came off of my Dart about 10 years ago. Worked fine then, been sitting on a shelf ever since. $40

NOS Cal Custom chrome dagger dipstick handle. $25

Mopar Performance 5 blade radiator fan and clutch. $100

1972 400 spark plug shields $10 pair

Factory warning light type oil pressure sending unit. $10

Chrome big block timing tab. $5

2 used Holley 450 cfm carbs, part number 9776, for dual quad set-ups. Carbs are in nice shape and worked fine the last time they were used. The only thing wrong with them is on one of them the small vacuum fitting that sticks out the side needs replacing as the tube broke off. $450 for the pair.

Chrome single groove alternator pulley. $15

New Mopar Performance big block 8 qt. oil pan with new pick-up. $200

1971 Charger big block throttle cable. $40

New AR Engineering big block lightweight alternator kit with 60 amp Denso alternator. I mounted this on my engine on the stand but ended up using a factory alternator. $175

Original 2 piece heat stove from 1970 440 exhaust manifold. Good condition. $125

1975 Date coded alternator. Part #3874271. $25

Pioneer Automotive cylinder head dowel pins. 21 pieces 1/4" x 5/8". $10

1967 4bbl intake manifold part# 2806178. Sandblasted and primed. $100

Rev-n-nator Coil and programmable ICU. $200

Vintage Cal Custom scoop style air cleaner. Very nice condition. Includes often missing matching wingnut. $300

New in boxes QTP 2 1/2" electric exhaust cutouts #QTEC50, stainless y-pipes #10250 and remote controller #10900. $654 total price at Summit. $500

Prices do not include shipping. No Paypal

gt340 @ yahoo.com

Fitment shows 77 440
Clean but dusty, everything moves freely.
Looks like it "could" go right onto an engine and run/ but not knowing exactly when it last did just that, I have to at least recommend it to be kitted before being bolted on and run again.
Been on a shelf in my garage for who knows how long
Asking $70. Plus the ride. Or local pickup. Preferably paid for by postal MO.

Big block cast iron passenger side exhaust manifold

Right hand manifold has a casting date of 3751074. It's also missing the heat control valve as shown in the photos. This one is $40 (plus shipping)

Needs to be cleaned up, but otherwise appear to be in fair enough shape with no apparent cracks. PM me for more photos. Located in West Sacramento.

Pair of big block spool mounts with special bolt. These fit the 1973-1974 B-body cars as well as the big block Direct Connection A-body K-frame. Not sure if these are new or just very clean and hardly used. Asking $30 for the pair. Contact Bud: Kramden426 at aol.com

Weiand intake manifold for a 413, 426W or 440 engine. Part # 7512. Looks like someone tried to do some porting. Will need some cleanup before using. Asking $100. Contact Bud: Kramden426 at aol.com

I have several used pairs of low block and raised block brackets, $15pr. Distributor hold downs, $25 each with correct bolt. Plus shipping. No Paypal, U.S. money order only. VEIGHTPETE@GMAIL.COM

For Sale: Very nice and tight, Direct Connection R/B original race, tach drive electronic distributor. Part # 3690201 This unit has the cast iron body. I have had this distributor a long time and it has always been stored in my house in a spare bedroom. This is a very clean and tight unit. The shaft doesn't wobble at all and play up and down is non-existent, the clips for the cap are very tight yet when snapping them in place or unsnapping them to take the cap off. I don't think this distributor has much use on it. This is a hard to find Direct Connection distributor for a nostalgia race build with a classic tach drive tachometer ( or a "Day 2" build) as well. Asking $225.00 which includes free shipping as long as you are in the lower 48 states. PM me here or E-mail me at; cloudone.70@gmail.com ------ Also if you need more photos just let me know. Thanks.

Brand new in the box Comp Cams solid roller, specs below. $425 plus shipping.

Reworked Aluminum -1 Heads. Originally Done by Nic at Compu Flow.
I had reworked by Burtonsville Performance Machine (Al Callway) after engine failure and have Not run.
At this time, Exhaust valves Replaced and some intakes, New Roller Springs, Locks and Keepers, Chambers and Guides addressed as needed and surfaced.
I just had Al recheck Spring Pressures- Set up at 1.98", 270#, .700" 630#, Coil Bind .800.
Comes with NEW Manley Bolt Package
Ran 9.28 in 3200# Demon w 499.

$3800 offer with Bolts, Can Ship

Also have TTI Low Deck 2-2 1/4 Step Headers available to Purchase and other Indy Top end Parts.

Reproduction 1962 to early 70 big block / Hemi distributor dual point vacuum advance. P/N TP-VACADV/BB/DPE. List price $110.

$90, plus shipping. I'm never offended by offers. TWSchuler@aol.com

NOS big block timing chain cover.

$60, plus shipping. I'm never offended by offers. TWSchuler@aol.com

SOLD SOLD For sale: complete 400 4 bbl engines with 727 transmissions. Both are complete carb to oil pan. They are out of mid to late 70s C bodies, both have about 70K miles. Both have run recently on an engine run stand. $800 EACH. Located in Millstadt, Illinois (just outside St. Louis). If interested please contact Ryan at 314-504-0634 thanks SOLD SOLD

Edelbrock proflo-4 for RB complete kit. Used just a short time(250 miles). Absolutely nothing wrong with it, was pulled off cause of hood clearance as we are going back to stock hood. Setup ran really good. Kit comes with everything to bolt on and fire up.
$1600+shipping

Big Block Throttle Cable Bracket. Used, $30 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097

383-400 Big Block A/C Brackets, Used, $75 + Shipping. Payment via US Postal Money Order. Shipping: US Address Only!
Call Steve 810-629-1097

Big Block Distributor Hold Down Bracket. Used, $20 + Shipping. Payment via US Postal Money Order. Shipping: US Address Only!
Call Steve 810-629-1097

Big Block Spark Plug Wire Brackets. Used, Payment via US Postal Money Order Only!. Shipping: US Address Only!
Call Steve 810-629-1097
1. $10 + Shipping
2. $20 + Shipping
3. $10 + Shipping

Big Block Timing Chain Cover. Used, $35 + Shipping. Payment via US Postal Money Order Only!. Shipping: US Address Only!
Call Steve 810-629-1097

Big Block Water Pump With Water Pump Housing. Used, $100 + Shipping. Payment via US Postal Money Order Only!. Shipping: US Address Only!
Call Steve 810-629-1097

Note: Came off a 1970 383 motor

Holley 4749 Carburetor Factory 383-440. Used, $125 + Shipping. Payment via US Postal Money Order. Shipping: US Address Only!
Call Steve 810-629-1097
Note: Came off a 70 383 Challenger

Factory Valve Cover Breather. Used, $15 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097

Valve Cover Oil Fill Caps. Used, $10 Each + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!

1. Not sure!
2. 73-74 model (came of my 73 Cuda)
3. Mopar Preformance Chrome New!
Call Steve 810-629-1097
Note: Pick the one you want by photo 1-3

73-74 Electric Choke #3656730 All Models, Used, $30 + Shipping. Payment via US Postal Money Order. Shipping: US Address Only!
Call Steve 810-629-1097

Fram CA160 Air Filter. New, $5 + Shipping. Payment via US Postal Money Order Only!. Shipping: US Address Only!
Call Steve 810-629-1097

Note: Used On Any 2bl Motor, See Photo 2 For Application!

63-76 Temperature Sending Switch #2426458 Used $7.50 + Shipping
62-80 Oil Pressure Sending Unit For Models With Warning Light. Used, $7.50 + Shipping.
Payment via US Postal Money Order Only!. Shipping: US Address Only!
Call Steve 810-629-1097

Factory Carburetor 3.5 in" Stud With Wing Nut. Used, $10 + Shipping. Payment via US Postal Money Order. Shipping: US Address Only!
Call Steve 810-629-1097

Water Pump To Fan Spacer 1.25 in' Thick. Used $15 + Shipping. Payment via US Postal Money Order Only!. Shipping: US Address Only!
Call Steve 810-629-1097

Gates Single Belts.New, $10 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!

1.Gates Belt 7470
2. Gates Belt 7490
3. Gates Belt 7580

Call Steve 810-629-1097
Note: Pick the one you want by photo 1-3

Gates / Mopar Duel Alternator / Fan Belts.New, Price Below + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!

1.Gates Duel Belt #7541 $20
2. Mopar Duel Belt #4106241 $25

Call Steve 810-629-1097
Note: Pick the one you want by photo 1-2

1969 440 HP block WS23L9G175918 or WS27L9G175918

You can see it is missing the body character in the stamping.
If you have one of those cars I could trade you parts if you wanted to reunite car and block.

Been in dry storage for many years. .030 and has 1 sleeve. $500 obo for block, caps, crank. Plus shipping if that is something you'd be interested in. Available in 52205 or 60188.

More photos available

For Sale, 1968 D model year 440 HP block, main caps and steel crank. Block is standard bore but has corrosion in 3 cylinders that should clean up under .060.
Casting date is 9/20/67
$600 obo

Can deliver to mopar shows in Stillwater MN, Carlisle or the nats with pre payment.

Located in menomonie, wi

Thanks

I have two sets and 4 spare BBM used main cap sets for the 2.75" crank journal. See pictures below.

$50 a set or $80 for the whole lot shipped in the lower 48 states. I will ship elsewhere for the added shipping cost.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

The 505ci that I’m selling is a pretty extensive build that produces a peak horsepower of 631@ 5,500rpm and 659lbs. ft. of torque at 4,500rpm all on 93 octane gas pumped from a Shell gas station down the street.

You’ll receive the full dyno report if you purchase it.

The parts list is as follows:

Chrysler RB440 engine block (7/8/1977) bored 0.030” over
K1 Technologies 4.25” stroke crank, 8-bolt Hemi flange
K1 Technologies 7.100” H-beam connecting rods
MAHLE Power Pak flat top pistons (11.7:1 compression, 0.025” in the hole)
MAHLE rings
Clevite bearings
SB Concepts billet main caps
SB Concepts billet steel girdle
ARP main studs
ARP cylinder head bolts
ARP intake manifold bolts
Mancini billet aluminum rear main seal
Milodon High Pressure Oil Pump
Milodon 3/8” pick up tube
Milodon 7qt. low profile pan

Trick Flow PowerPort Top End Engine Kit:
• Trick Flow PowerPort 240 aluminum cylinder heads (78cc chambers)
• Trick Flow Track Heat square bore 4150 single plane intake manifold
• Trick Flow dual valve springs
• Harland Sharpe roller rockers & shafts
• Howard Cams hydraulic roller lifters
• COMP Cams push rods
• Trick Flow hydraulic roller camshaft (243 int./247 exh. @ .050” lift, 0.640 int./0.640 exh.)

COMP Cams bronze gear oil pump driveshaft
COMP Cams double roller timing chain
Milodon bronze gear intermediate shaft
PRW baffled, aluminum valve covers
440 Source hydraulic damper
440 Source crank & water pump pulley
Mancini aluminum water pump & housing
Mancini stamped valley pan
440 Source valley pan retainers & hardware

*This does not include carburetor, ignition (distributor, plugs or wires), or exhaust. Long block only.

Just by the parts list and machine work is a $16,800 engine, but I’m asking $14,500 or best offer.

email me directly at charged1969@hotmail.com

Brand New in the box Big Block Chrysler/Mopar Pro-Flo XT EFI Part # 7144 Manifold

Designed for 413-440 Chrysler motors, the Pro-Flo XT Chrysler 440 EFI intake manifold is engineered with a large plenum and long tapered runners to deliver maximum horsepower. This manifold delivers a broad torque band throughout the rpm range of 1500-7000 rpm. $450 + shipping PM here or Phone (716) 655-0625 this is a land line. Ask for Gary This manifold sell for $668 at Jegs and Summit

SMR transmissions B/RB to small block transmission adapter kit. Part number SM 99-100P for a 6 bolt crank. New in box, the box has been opened but only for inspection, never installed the kit. for info: https://smrtrans.tripod.com/smrtransmissionsintro/id9.html $400 + shipping. PM here or phone (716) 655-0625 ask for Gary or leave a message ( this is a land line)

For sale - 516 heads that have been in my basement work room for a 5+ years - they came (just as you see in the pics) along with an engine block I purchased that I needed for a resto. - looks like a rebuild/refresh was done.

Rather not ship - I'm in MD - happy to travel a few hours to meet.

$200 - shoot me a PM

Just re - joined Moparts - Hi All..

For sale - 70's 440 cast crank - stored in same basement as the heads I posted - some rust but maybe savable - quick measurement on journals - all 2.375
Rather not ship - I'm in MD - happy to travel a few hours to meet.

$100 - PM if interested

1967 Carter 383 Carburetor 4298S

Used, Original 1967 Carter 4298S (A7 = Jan. 1967) Carb, for 383 engine with manual transmission.
Needs to be restored. Missing a few bolts & secondary throttle shaft/plate assembly.
Asking $95 shipped in US.
If interested or need more pictures, send email: chargercrazed@usa.com

Application is listed in 70-71 Parts Catalog as for 383/440 with a/c and 2.71/2.76 axle, 6" diameter, B/J/P/D/C vehicles
Has always been properly stored in box face down
$150.00 + shipping from 08724 NJ