Who to call for solid roller cam
#2783647
06/10/20 12:50 PM
06/10/20 12:50 PM
|
Joined: Mar 2009
Posts: 1,058 bigfork mn
dragram440
OP
super stock
|
OP
super stock
Joined: Mar 2009
Posts: 1,058
bigfork mn
|
I am putting a new set of Trick Flow power port 270 heads on my 500 CI RB and need to have someone spec a cam for me. I bought a used one and it doesn't seem to fit. The bearings seem to be to tight. Weird thing is I have had 3 different cams in these exact bearings. I would assume the used one I bought is bent or not the right tolerance to start with. I was going to call Hughes engines. Any other suggestions? Thanks in advance.
67' charger 499 RB
10.57 at 127
|
|
|
Re: Who to call for solid roller cam
[Re: tboomer]
#2783663
06/10/20 01:07 PM
06/10/20 01:07 PM
|
Joined: Jan 2003
Posts: 4,270 Morrow, OH
markz528
master
|
master
Joined: Jan 2003
Posts: 4,270
Morrow, OH
|
Dwayne Porter..He will fix ya up right! What block are you using?
67 Coronet 500 9.610 @ 139.20 mph 67 Coronet 500 (street car) 14.82 @ 94 mph 69 GTX (clone) - build in progress......
|
|
|
Re: Who to call for solid roller cam
[Re: markz528]
#2783666
06/10/20 01:10 PM
06/10/20 01:10 PM
|
Joined: Mar 2009
Posts: 1,058 bigfork mn
dragram440
OP
super stock
|
OP
super stock
Joined: Mar 2009
Posts: 1,058
bigfork mn
|
Stock 1969 440 block. Same block i have been running the last 8 years with this 500" setup.
67' charger 499 RB
10.57 at 127
|
|
|
Re: Who to call for solid roller cam
[Re: dragram440]
#2783669
06/10/20 01:11 PM
06/10/20 01:11 PM
|
Joined: Aug 2003
Posts: 43,181 Bend,OR USA
Cab_Burge
I Win
|
I Win
Joined: Aug 2003
Posts: 43,181
Bend,OR USA
|
I'm sure Dwayne is good but you might want to call Bullet Cams,662-893-5670 or Ultradyne cams at 662-893-8022. They are in the same shop so either one should be able to help you on getting a good cam, they are Mopar specialists also
Last edited by Cab_Burge; 06/10/20 01:12 PM.
Mr.Cab Racing and winning with Mopars since 1964. (Old F--t, Huh)
|
|
|
Re: Who to call for solid roller cam
[Re: dragram440]
#2783671
06/10/20 01:13 PM
06/10/20 01:13 PM
|
Joined: Aug 2003
Posts: 4,679 On the parachute mount
n20mstr
master
|
master
Joined: Aug 2003
Posts: 4,679
On the parachute mount
|
I use Scott Brown for any camshaft …..
IF you have cams that spin and one that doesn't? sounds like that cam may be a lil bent???. Usually if the bearings are new, they may be a little tight and need a scraping here and there, BUT that should be with any cam, not just one.
Good luck
....BAD A$$ STREET CAR.....
|
|
|
Re: Who to call for solid roller cam
[Re: n20mstr]
#2783732
06/10/20 02:52 PM
06/10/20 02:52 PM
|
Joined: Jan 2003
Posts: 10,022 MN
JERICOGTX
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 10,022
MN
|
With no disrespect to Dwayne, I like my Scott Brown cam. Now all my head work will go to Dwayne...
69 GTX
68 Road Runner
|
|
|
Re: Who to call for solid roller cam
[Re: JERICOGTX]
#2783738
06/10/20 02:59 PM
06/10/20 02:59 PM
|
Joined: Mar 2009
Posts: 1,058 bigfork mn
dragram440
OP
super stock
|
OP
super stock
Joined: Mar 2009
Posts: 1,058
bigfork mn
|
How do I get a hold of Scott Brown? Not finding anything googling it.
67' charger 499 RB
10.57 at 127
|
|
|
Re: Who to call for solid roller cam
[Re: n20mstr]
#2783802
06/10/20 05:41 PM
06/10/20 05:41 PM
|
Joined: Oct 2006
Posts: 1,264 New York, USA
Chargerfan68
pro stock
|
pro stock
Joined: Oct 2006
Posts: 1,264
New York, USA
|
No question....Dwayne Porter for all and any camshafts!!
1.50 60Ft. , 10.75@ 127MPH Hauling 3900 LBS.
|
|
|
Re: Who to call for solid roller cam
[Re: dragram440]
#2783842
06/10/20 07:25 PM
06/10/20 07:25 PM
|
Joined: Mar 2006
Posts: 2,675 Mt. Eden Ky.
Hemi Allstate
master
|
master
Joined: Mar 2006
Posts: 2,675
Mt. Eden Ky.
|
I would call Dwayne Porter . Mark
1996 Ram 1500 Sport 1968 road runner 1952 Sears Allstate licensed, pump gas, Hemi 5.98 @ 115.73 1.33 60 ft. The best is yet to come. Painless Performance / Street RODDER magazine Top 100 for 2019
|
|
|
Re: Who to call for solid roller cam
[Re: Hemi Allstate]
#2783914
06/10/20 10:11 PM
06/10/20 10:11 PM
|
Joined: Jan 2003
Posts: 3,504 DFW
mr_340
master
|
master
Joined: Jan 2003
Posts: 3,504
DFW
|
I would call Billy Godbold at Comp Cams. I would bet he has the latest designs.
Last edited by mr_340; 06/10/20 10:11 PM. Reason: typo
Floyd Lippencott IV
|
|
|
Re: Who to call for solid roller cam
[Re: mopar dave]
#2783940
06/10/20 11:22 PM
06/10/20 11:22 PM
|
Joined: Mar 2009
Posts: 1,058 bigfork mn
dragram440
OP
super stock
|
OP
super stock
Joined: Mar 2009
Posts: 1,058
bigfork mn
|
12.25-1 i might have the heads decked to get the chambers down a little. Trick flow 270 heads
67' charger 499 RB
10.57 at 127
|
|
|
Re: Who to call for solid roller cam
[Re: mr_340]
#2784012
06/11/20 09:40 AM
06/11/20 09:40 AM
|
Joined: Dec 2007
Posts: 12,587 Great Neck,LI,new york
hemi-itis
I Live Here
|
I Live Here
Joined: Dec 2007
Posts: 12,587
Great Neck,LI,new york
|
Funny thing about calling cam companies,,,,,called Comp for instance 5 times and got 6 different cams. My next cam would be spec'd by Dwayne! It's all about the combination!!!
HEMI-ITIS has no cure. My condition is fully BLOWN!!
|
|
|
Re: Who to call for solid roller cam
[Re: dragram440]
#2784018
06/11/20 09:54 AM
06/11/20 09:54 AM
|
Joined: Jun 2003
Posts: 52,972 Romeo MI
MR_P_BODY
Master
|
Master
Joined: Jun 2003
Posts: 52,972
Romeo MI
|
How do I get a hold of Scott Brown? Not finding anything googling it. I ran a Scott Brown cam for a few years.. that cam was just down right WRONG for my set up and he speced it out and I didnt like the 112 center line which he really likes.. if this is a race set up you would be better off with Ultridyne
|
|
|
Re: Who to call for solid roller cam
[Re: hemi-itis]
#2784040
06/11/20 11:06 AM
06/11/20 11:06 AM
|
Joined: Jul 2004
Posts: 19,317 State of confusion
Thumperdart
I Live Here
|
I Live Here
Joined: Jul 2004
Posts: 19,317
State of confusion
|
And why Isky is the best overall in MY world and all I use plus my roller has the most aggressive street-ish lobes while being easy on parts. 14+ years and changed springs twice and rebuilt the roller lifters once so far. Easy mid 9's and 6-teens so far and driven a good amount.......680-.660 276-281 on a 108 lsa w/97 degrees of overlap.....
Last edited by Thumperdart; 06/11/20 11:10 AM.
72 Dart 470 n/a BB stroker street car `THUMPER`...Check me out on FB Dominic Thumper for videos and lots of carb pics......760-900-3895.....
|
|
|
|
|