Re: Anyone used MT ET Street R bias tires?
[Re: fbs63]
#2529961
08/01/18 01:13 PM
08/01/18 01:13 PM
|
Joined: Jan 2003
Posts: 11,711 Portage,michigan
B3422W5
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 11,711
Portage,michigan
|
Yep. Ran them on my 9 sec s/s spring Duster for years and they would hook on ice. Great tire.
69 Dart GTS A4 Silver All steel, flat factory hood, 3360race weight 418 BPE factory replacement headed stroker, 565 lift solid cam Best so far, 10.40 @127 1/4 1.41 best 60 foot 6.60 at 103.90 1/8
|
|
|
Re: Anyone used MT ET Street R bias tires?
[Re: justinp61]
#2529977
08/01/18 01:41 PM
08/01/18 01:41 PM
|
Joined: Jan 2003
Posts: 11,711 Portage,michigan
B3422W5
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 11,711
Portage,michigan
|
Yep. I liked runnng tubes because the sidewall became stiffer. And i did use screws.
69 Dart GTS A4 Silver All steel, flat factory hood, 3360race weight 418 BPE factory replacement headed stroker, 565 lift solid cam Best so far, 10.40 @127 1/4 1.41 best 60 foot 6.60 at 103.90 1/8
|
|
|
Re: Anyone used MT ET Street R bias tires?
[Re: justinp61]
#2529979
08/01/18 01:42 PM
08/01/18 01:42 PM
|
Joined: Jan 2003
Posts: 13,363 Marion, South Carolina [><]
an8sec70cuda
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 13,363
Marion, South Carolina [><]
|
Like any other bias ply tire, if you run a tube in them, you need to be sure the tire doesn't slip on the rim. Either screws or beadlocks would be my suggestion. Gluing them, like you do with radials, isn't guaranteed and isn't worth the chance of tearing the tube and losing air pressure going down the track.
Don't want screws or beadlocks? Then go tubeless and just deal w/ a lil leakage. I have not run the new ET Street R tires, but I ran the old ET Street bias ply tires for many years. They'd lose a couple or 3 pounds of air overnight w/o tubes...no big deal.
CHIP '70 hemicuda, 575" Hemi, 727, Dana 60 '69 road runner, 440-6, 18 spline 4 speed, Dana 60 '71 Demon, 340, low gear 904, 8.75 '73 Chrysler New Yorker, 440, 727, 8.75 '90 Chevy 454SS Silverado, 476" BBC, TH400, 14 bolt '06 GMC 2500HD LBZ Duramax
|
|
|
Re: Anyone used MT ET Street R bias tires?
[Re: an8sec70cuda]
#2529982
08/01/18 01:47 PM
08/01/18 01:47 PM
|
Joined: Feb 2005
Posts: 20,173 PA.
pittsburghracer
"Little"John
|
"Little"John
Joined: Feb 2005
Posts: 20,173
PA.
|
You guys that have leaking tires going tubless aren’t prepping them right.
1970 Duster Edelbrock headed 408 5.984@112.52 422 Indy headed small block 5.982@112.56 mph 9.42@138.27
Livin and lovin life one day at a time
|
|
|
Re: Anyone used MT ET Street R bias tires?
[Re: pittsburghracer]
#2530002
08/01/18 02:21 PM
08/01/18 02:21 PM
|
Joined: Jan 2003
Posts: 11,711 Portage,michigan
B3422W5
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 11,711
Portage,michigan
|
You guys that have leaking tires going tubless aren’t prepping them right. With radials i have went tubeless, but with bias tires i always ran tubes. Just stiffen up the tire a good bit. Nothing to do with leaking
69 Dart GTS A4 Silver All steel, flat factory hood, 3360race weight 418 BPE factory replacement headed stroker, 565 lift solid cam Best so far, 10.40 @127 1/4 1.41 best 60 foot 6.60 at 103.90 1/8
|
|
|
Re: Anyone used MT ET Street R bias tires?
[Re: mopar dave]
#2530035
08/01/18 03:52 PM
08/01/18 03:52 PM
|
Joined: Oct 2003
Posts: 11,684 W. Kentucky
justinp61
OP
I Live Here
|
OP
I Live Here
Joined: Oct 2003
Posts: 11,684
W. Kentucky
|
Rubbing dawn dish soap on inside of tires works for me. Rarely have to add air. This is what I've done with slicks and had good results. The reason I was looking at the MT tires is that are supposed to have a stiffer sidewall.
|
|
|
Re: Anyone used MT ET Street R bias tires?
[Re: justinp61]
#2530038
08/01/18 04:01 PM
08/01/18 04:01 PM
|
Joined: Feb 2005
Posts: 20,173 PA.
pittsburghracer
"Little"John
|
"Little"John
Joined: Feb 2005
Posts: 20,173
PA.
|
I coat mine with a Dawn and water solution and let it dry. The next day I coat them again then I prep and clean the bead to remove the "mold compound" with paint thinner, scuff them with red scott pad, and clean them again. Then I glue them on with High Tach sealer. I lose less than 1 pound of air during 5 months of winter storage.
1970 Duster Edelbrock headed 408 5.984@112.52 422 Indy headed small block 5.982@112.56 mph 9.42@138.27
Livin and lovin life one day at a time
|
|
|
Re: Anyone used MT ET Street R bias tires?
[Re: justinp61]
#2530104
08/01/18 05:44 PM
08/01/18 05:44 PM
|
Joined: Jan 2003
Posts: 11,711 Portage,michigan
B3422W5
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 11,711
Portage,michigan
|
I think people are confusing the “ running them without tubes “ and they leak. Everybody seems to know how to make the tires hold air without tubes....... My point wasnt about holding air, my point was i run tubes on QTP’s only because it stiffens the sidewall. I have run them with and without tubes, prefer tubes, stiffer sidewall
69 Dart GTS A4 Silver All steel, flat factory hood, 3360race weight 418 BPE factory replacement headed stroker, 565 lift solid cam Best so far, 10.40 @127 1/4 1.41 best 60 foot 6.60 at 103.90 1/8
|
|
|
Re: Anyone used MT ET Street R bias tires?
[Re: justinp61]
#2530295
08/02/18 12:59 AM
08/02/18 12:59 AM
|
Joined: Jul 2004
Posts: 1,145 Arizona, USA
gsmopar
super stock
|
super stock
Joined: Jul 2004
Posts: 1,145
Arizona, USA
|
I think it was BIGCUBE that posted several years ago and I'm paraphrasing: SFI wheels don't need bead locks or screws with tubes. Anyway, I tried it. Mid 10's, 3700lbs, MT ET Bias Streets, Tubes, no screws. Many many many passes, no issues.
|
|
|
Re: Anyone used MT ET Street R bias tires?
[Re: justinp61]
#2530419
08/02/18 11:38 AM
08/02/18 11:38 AM
|
Joined: Dec 2007
Posts: 12,587 Great Neck,LI,new york
hemi-itis
I Live Here
|
I Live Here
Joined: Dec 2007
Posts: 12,587
Great Neck,LI,new york
|
I have the new style MT ET street r 16.5x31 for my street tires,Coated with dishsoap on a 12 rim with no tubes.They still will leak a few lbs intermittently.I don't normally race with then as I have a pair of MT 10.5w's slicks on another set of rims for the track. I made 4 passes at South Mountain on the Carlisle weekend and they hooked up well lifting the front tires.In the 90* heat and 85% humidity it still went 6.13 @ 113.I had my slicks with me for Sunday but it rained.I was curious what the difference would have been between the 2
HEMI-ITIS has no cure. My condition is fully BLOWN!!
|
|
|
Re: Anyone used MT ET Street R bias tires?
[Re: second 70]
#2530455
08/02/18 01:27 PM
08/02/18 01:27 PM
|
Joined: Jan 2003
Posts: 14,496 So. Burlington, Vt.
fast68plymouth
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 14,496
So. Burlington, Vt.
|
OT, but that is one sweet looking blue Cuda!!!
68 Satellite, 383 with stock 906’s, 3550lbs, 11.18@123 Dealer for Comp Cams/Indy Heads
|
|
|
Re: Anyone used MT ET Street R bias tires?
[Re: justinp61]
#2530555
08/02/18 05:12 PM
08/02/18 05:12 PM
|
Joined: Jul 2004
Posts: 19,317 State of confusion
Thumperdart
I Live Here
|
I Live Here
Joined: Jul 2004
Posts: 19,317
State of confusion
|
These were ran on the street/ Tubes and screws? Yep and a 1.33 60 ft.............
72 Dart 470 n/a BB stroker street car `THUMPER`...Check me out on FB Dominic Thumper for videos and lots of carb pics......760-900-3895.....
|
|
|
Re: Anyone used MT ET Street R bias tires?
[Re: justinp61]
#2530756
08/03/18 12:02 AM
08/03/18 12:02 AM
|
Joined: Jul 2006
Posts: 4,319 Puyallup, WA
StealthWedge67
master
|
master
Joined: Jul 2006
Posts: 4,319
Puyallup, WA
|
M/T’s website says they are designed “with all the latest technology of the ET Drag”. That’s marketing speak for: “it’s an ET Drag with some grooves in the tread”.
LemonWedge - Street heavy / Strip ready - 11.07 @ 120
|
|
|
|
|