Re: aluminum hemi valve covers
[Re: never2ready]
#242208
03/03/09 06:51 PM
03/03/09 06:51 PM
|
Joined: Jan 2003
Posts: 13,363 Marion, South Carolina [><]
an8sec70cuda
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 13,363
Marion, South Carolina [><]
|
Not sure about the fabricated aluminum covers, but as far as cast aluminum hemi covers go...I like my Indy hemi valve covers. CHIP
CHIP '70 hemicuda, 575" Hemi, 727, Dana 60 '69 road runner, 440-6, 18 spline 4 speed, Dana 60 '71 Demon, 340, low gear 904, 8.75 '73 Chrysler New Yorker, 440, 727, 8.75 '90 Chevy 454SS Silverado, 476" BBC, TH400, 14 bolt '06 GMC 2500HD LBZ Duramax
|
|
|
Re: aluminum hemi valve covers
[Re: Defbob]
#242211
03/03/09 07:15 PM
03/03/09 07:15 PM
|
Joined: Apr 2004
Posts: 48
never2ready
OP
member
|
OP
member
Joined: Apr 2004
Posts: 48
|
|
|
|
Re: aluminum hemi valve covers
[Re: hemi-itis]
#242217
03/04/09 10:11 AM
03/04/09 10:11 AM
|
Joined: Jan 2004
Posts: 4,866 North of Detroit
HemiDart68
master
|
master
Joined: Jan 2004
Posts: 4,866
North of Detroit
|
I have worked with Jeff Johnsons fabricated, Moroso, and BLP products. The Moroso's are decent, but they are big. Just basically a big square, they are alot harder to fit in the car. The Jeff Johnson ones i had issues with. The ones on ebay look identical to the jeff johnson covers. BLP makes hands down the best fabricated hemi valve cover currently on the market. It is built on billet rail with the gasket groove CNC'd into the rail. Everything fits the way it is supposed too, and they look awesome.
Last edited by HemiDart68; 03/04/09 10:28 AM.
In God we trust, all others pay cash.
www.lightnens.com (Home of the world's fastest Paint Job)
|
|
|
Re: aluminum hemi valve covers
[Re: HemiDart68]
#242218
03/04/09 10:34 AM
03/04/09 10:34 AM
|
Joined: Jan 2004
Posts: 4,866 North of Detroit
HemiDart68
master
|
master
Joined: Jan 2004
Posts: 4,866
North of Detroit
|
Just re-read the ebay ones, they are the williams manufacturing covers. They are nice, but the BLP is a nicer piece IMHO.
In God we trust, all others pay cash.
www.lightnens.com (Home of the world's fastest Paint Job)
|
|
|
Re: aluminum hemi valve covers
[Re: Hemi Allstate]
#242219
03/04/09 11:18 AM
03/04/09 11:18 AM
|
Joined: May 2004
Posts: 12,387 Taxes & Virus's R-US, NY
Dragula
I Live Here
|
I Live Here
Joined: May 2004
Posts: 12,387
Taxes & Virus's R-US, NY
|
Quote:
I like the Old School look.
Keith Blacks on my new Hemi. http://stores.casselent.com/catalog/KB%20COVERS.jpg
Here are some other choices. Check both pages. http://stores.casselent.com/Categories.b...=9&total=14
I think those would sell to more people, if you wouldn't have the breather locations already machined, and let people put in the what they want. That's why mine were the plain looking Indy valve covers. I could put everything where I wanted, and use what I wanted for breathers. I do not reccomend buying them thru Indy, but they are simple, they clear big springs, and seal very well.
If I were to buy fabricated covers, they would have to made such that all of the bolts are thru the cover with the heads protruding thru the top. I say this because the rails closest to the fenders are tough to get at and get a wrench on them. I have only seen one set where all the bolt heads were real long.....If they are resessed way down, good luck getting at them if you have Indy hemi heads.
|
|
|
Re: aluminum hemi valve covers
[Re: Dragula]
#242220
03/04/09 11:24 AM
03/04/09 11:24 AM
|
Joined: May 2004
Posts: 12,387 Taxes & Virus's R-US, NY
Dragula
I Live Here
|
I Live Here
Joined: May 2004
Posts: 12,387
Taxes & Virus's R-US, NY
|
Here is a set of fabricated ones I like. I will also mention the Indy's have a nice feature, and they have two of the attaching bolts deleted, but drilled from the inside for a stud. This is a really nice feature. The short studs remain on the heads and retain the gaskets, and really make the covers easier to remove because the deleted bolt holes are the ones on the ends (firewall side delete is the best). Really cleans up the look of the covers as well, as you will notice in the pic of my engine where they are not present. I do not like Indy's service, but some of their products I really like.
With the fabricated ones shown below, it would also be nice to delete the same two bolts per valve cover, but as mentioned, I like the fabricated ones where all the bolts are not recessed real deep into the covers. Flush would be ok, but the fender well side ones that are recessed real deep are a pain.
|
|
|
Re: aluminum hemi valve covers
[Re: sunroofgtx]
#242222
03/04/09 11:44 AM
03/04/09 11:44 AM
|
Joined: Jan 2003
Posts: 19,363 Las Vegas
Al_Alguire
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 19,363
Las Vegas
|
Another vote here for BLP. The Williams ones are nice as well. Here is Matt's motor
"I am not ashamed to confess I am ignorant of what I do not know."
"It's never wrong to do the right thing"
|
|
|
Re: aluminum hemi valve covers
[Re: Al_Alguire]
#242224
03/04/09 02:53 PM
03/04/09 02:53 PM
|
Joined: Jan 2004
Posts: 4,866 North of Detroit
HemiDart68
master
|
master
Joined: Jan 2004
Posts: 4,866
North of Detroit
|
That is a slightly dated pic with the Jeff Johnson covers, ill see if i can dig one up with the BLP's I havn't had them on my car long. i might have a pic at my home p.c.
In God we trust, all others pay cash.
www.lightnens.com (Home of the world's fastest Paint Job)
|
|
|
Re: aluminum hemi valve covers
[Re: HemiDart68]
#242225
03/04/09 04:13 PM
03/04/09 04:13 PM
|
Joined: Jan 2004
Posts: 4,866 North of Detroit
HemiDart68
master
|
master
Joined: Jan 2004
Posts: 4,866
North of Detroit
|
Rick the above pic was with magnacore wires, and Jeff johnson covers
this is the car with MSD wires and BLP covers
In God we trust, all others pay cash.
www.lightnens.com (Home of the world's fastest Paint Job)
|
|
|
|
|