Re: Trend Tool Steel Lifters
[Re: Hot 340]
#2272662
03/19/17 11:45 PM
03/19/17 11:45 PM
|
Joined: Jan 2003
Posts: 15,439 Val-haul-ass... eventually
BradH
Taking time off to work on my car
|
Taking time off to work on my car
Joined: Jan 2003
Posts: 15,439
Val-haul-ass... eventually
|
I checked out their website and admit it left me a bit confused. They have a number of options with a pretty wide price range, and it wasn't clear what some of the differences even were. It did say they're reusable, but also mentioned they can be returned to have the faces re-profiled... but I don't know if that means you're supposed to have them refaced before being reused
Like I said, kind of confusing.
Last edited by BradH; 03/19/17 11:46 PM.
|
|
|
Re: Trend Tool Steel Lifters
[Re: Hot 340]
#2272737
03/20/17 02:18 AM
03/20/17 02:18 AM
|
Joined: Aug 2011
Posts: 2,872 Pattison Texas
CSK
master
|
master
Joined: Aug 2011
Posts: 2,872
Pattison Texas
|
I have them in my 512 ci street strip car, they said to use cast core, & non coated lifters, 2500 street miles & so far so good.
1968 Charger COLD A/C Hilborn EFI 512ci 9.7 compression, Stealth heads, 4.10 gear A518 ODtrans 4100lb,10.93 full street car trim 2020 T/A 392 Stock 11.79 @ 114.5
|
|
|
Re: Trend Tool Steel Lifters
[Re: Hot 340]
#2272871
03/20/17 11:32 AM
03/20/17 11:32 AM
|
Joined: Jan 2003
Posts: 12,289 Benton, IL.
DaveRS23
Special needs idiot
|
Special needs idiot
Joined: Jan 2003
Posts: 12,289
Benton, IL.
|
I have Barton's lifters in my engine. Does anyone know who makes them?
Master, again and still
|
|
|
Re: Trend Tool Steel Lifters
[Re: DaveRS23]
#2272904
03/20/17 12:17 PM
03/20/17 12:17 PM
|
Joined: Feb 2005
Posts: 20,201 PA.
pittsburghracer
"Little"John
|
"Little"John
Joined: Feb 2005
Posts: 20,201
PA.
|
I put the EDM solid lifters in my 600 plus lift cam in my 422 small block. They seem to be working but the next time this engine comes apart I'm upgrading to a bigger roller cam. ( R3 block grinding necessary )
1970 Duster Edelbrock headed 408 5.984@112.52 422 Indy headed small block 5.982@112.56 mph 9.42@138.27
Livin and lovin life one day at a time
|
|
|
Re: Trend Tool Steel Lifters
[Re: rickseeman]
#2273243
03/20/17 08:50 PM
03/20/17 08:50 PM
|
Joined: Jan 2003
Posts: 6,150 Melbourne , Australia
LA360
master
|
master
Joined: Jan 2003
Posts: 6,150
Melbourne , Australia
|
Being as hard as they are, they should swap over from cam to cam. Like anything though, they will wear out eventually. I see what you mean Brad, the options aren't the clearest, if I was ordering them I'd be contacting Trend direct and telling them what I want. The DLC coating seems to almost double the cost.
Alan Jones
|
|
|
Re: Trend Tool Steel Lifters
[Re: Hot 340]
#2273284
03/20/17 09:50 PM
03/20/17 09:50 PM
|
Joined: Jan 2003
Posts: 8,183 Plymouth, MI
Blusmbl
master
|
master
Joined: Jan 2003
Posts: 8,183
Plymouth, MI
|
DLC is also used on dirt bike forks- only on the factory level suspensions though. No bike has come with it stock if I remember correctly.
'18 Ford Raptor, random motorcycles, 1968 Plymouth Fury III - 11.37 @ 118
|
|
|
Re: Trend Tool Steel Lifters
[Re: rickseeman]
#2273290
03/20/17 09:55 PM
03/20/17 09:55 PM
|
Joined: Jan 2003
Posts: 12,289 Benton, IL.
DaveRS23
Special needs idiot
|
Special needs idiot
Joined: Jan 2003
Posts: 12,289
Benton, IL.
|
I have Barton's lifters in my engine. Does anyone know who makes them? Trend Thank you!
Master, again and still
|
|
|
Re: Trend Tool Steel Lifters
[Re: Hot 340]
#2273310
03/20/17 10:21 PM
03/20/17 10:21 PM
|
Joined: May 2004
Posts: 12,418 Taxes & Virus's R-US, NY
Dragula
I Live Here
|
I Live Here
Joined: May 2004
Posts: 12,418
Taxes & Virus's R-US, NY
|
Has anybody tried these and what did they recommend for a cast cam core?- as they have a lot of options. And can they be used repeatedly? Had a set in my 605 Hemi last year.....Just go roller and be done with it. I don;t care what oil, break in, etc, etc you do, its gonna fail.....
|
|
|
Re: Trend Tool Steel Lifters
[Re: Dragula]
#2273535
03/21/17 10:07 AM
03/21/17 10:07 AM
|
Joined: Nov 2011
Posts: 289 PA
Harry's Taxi 2
enthusiast
|
enthusiast
Joined: Nov 2011
Posts: 289
PA
|
Has anybody tried these and what did they recommend for a cast cam core?- as they have a lot of options. And can they be used repeatedly? Had a set in my 605 Hemi last year.....Just go roller and be done with it. I don;t care what oil, break in, etc, etc you do, its gonna fail..... What happened to yours?
'86 Maple Grove KOS Mopar low qualifier......true street legal with no power adders.
NOS-used when losing since 1940.
|
|
|
Re: Trend Tool Steel Lifters
[Re: Hot 340]
#2274425
03/22/17 08:04 PM
03/22/17 08:04 PM
|
Joined: Nov 2006
Posts: 733 jacksonville,FLORIDA
slammedR/T
super stock
|
super stock
Joined: Nov 2006
Posts: 733
jacksonville,FLORIDA
|
Been running MRL performance lifters in my 410cui small block with plenty of street driving since 2013 with zero issues.
2000 Dakota R/T, 408 magnum, 727, Indy heads 1000cfm 4150 carb, 93 octane fuel. motor; 10.258 @ 132.78 200 shot; 9.262 @ 144.69 racemagnum
|
|
|
Re: Trend Tool Steel Lifters
[Re: slammedR/T]
#2274861
03/23/17 04:10 PM
03/23/17 04:10 PM
|
Joined: Jan 2003
Posts: 15,439 Val-haul-ass... eventually
BradH
Taking time off to work on my car
|
Taking time off to work on my car
Joined: Jan 2003
Posts: 15,439
Val-haul-ass... eventually
|
Been running MRL performance lifters in my 410cui small block with plenty of street driving since 2013 with zero issues. Roller or flat-tappet? I know MRL sells B.A.M. roller lifters, but didn't think he had anything special in an SFT.
|
|
|
|
|