Brake Bleeding Tool,,,,help,,,questions...
#201282
01/22/09 07:04 PM
01/22/09 07:04 PM
|
Joined: Jan 2003
Posts: 4,852 KENTUCKY
69CHARGERMD
OP
master
|
OP
master
Joined: Jan 2003
Posts: 4,852
KENTUCKY
|
Question: I am bleeding the brakes on the Charger,,,and not sure it is going right. I have a Mityvac (see pic below),,,i have used it before without too much problem. I seem to be seeing ALOT of bubbles in the plastic tubing lines when i try and bleed the system. I am having a hard time telling if it is working or not ? I am wondering if some of the problem could be with the bleeder screw allowing air around the threads where it screws into the wheel cylinder ?? The bleeder screw does get a bit "wobbly" after i loosen it up to bleed them,, Dumb question ...but how "loose" should that bleeder screw be ? enough to see a small drip,,stream,,? I am going to try and find the manual for the Mityvac thing i have and see if it has a trouble shooting guide........ thanks for any advice... Doug
|
|
|
Re: Brake Bleeding Tool,,,,help,,,questions...
[Re: 69CHARGERMD]
#201283
01/22/09 07:24 PM
01/22/09 07:24 PM
|
Joined: Nov 2003
Posts: 36,041 Lincoln Nebraska
RapidRobert
Circle Track
|
Circle Track
Joined: Nov 2003
Posts: 36,041
Lincoln Nebraska
|
that's too loose , you are pulling air back in if it's wobbly. You want ~1/8-1/4 turn
live every 24 hour block of time like it's your last day on earth
|
|
|
Re: Brake Bleeding Tool,,,,help,,,questions...
[Re: 69CHARGERMD]
#201284
01/22/09 08:43 PM
01/22/09 08:43 PM
|
Joined: Jan 2003
Posts: 5,920 Athens, Greece
Pyper70
master
|
master
Joined: Jan 2003
Posts: 5,920
Athens, Greece
|
I have heard....HEARD.....that if you are doing it by yourself and you aren't in a rush, you can raise the front end and crack the bleeder screws loose and leave it there for 2-3 days and the air bubbles naturally rise to the highest point in the line (the bleeder screw). tighten em down and raise the rear and let that naturally get rid of the bubbles, crank the bleeders shut and your brakes should be good.
Again, I have never done this, only heard of it
Family owned 1969 Charger R/T DualQuad 440/727/GVO/3.55s
|
|
|
Re: Brake Bleeding Tool,,,,help,,,questions...
[Re: Pyper70]
#201285
01/22/09 08:56 PM
01/22/09 08:56 PM
|
Joined: Jun 2005
Posts: 1,534 Florida
CHRGR69
pro stock
|
pro stock
Joined: Jun 2005
Posts: 1,534
Florida
|
Quote:
I have heard....HEARD.....that if you are doing it by yourself and you aren't in a rush, you can raise the front end and crack the bleeder screws loose and leave it there for 2-3 days and the air bubbles naturally rise to the highest point in the line (the bleeder screw). tighten em down and raise the rear and let that naturally get rid of the bubbles, crank the bleeders shut and your brakes should be good.
OK let me get this straight because I may try it. Alone with plenty of time. Jack up front, crack screws, leave 2-3 days, tighten and lower. Then do the same for the rear end??
Again, I have never done this, only heard of it
Grandma always said I had "hands of gold"!
|
|
|
Re: Brake Bleeding Tool,,,,help,,,questions...
[Re: 69CHARGERMD]
#201286
01/22/09 09:00 PM
01/22/09 09:00 PM
|
Joined: Jan 2003
Posts: 4,902 Virginia
BSharp
Righteous, and as a result, fearless of mods
|
Righteous, and as a result, fearless of mods
Joined: Jan 2003
Posts: 4,902
Virginia
|
|
|
|
Re: Brake Bleeding Tool,,,,help,,,questions...
[Re: CHRGR69]
#201287
01/22/09 09:03 PM
01/22/09 09:03 PM
|
Joined: Jan 2003
Posts: 5,920 Athens, Greece
Pyper70
master
|
master
Joined: Jan 2003
Posts: 5,920
Athens, Greece
|
Thats just what I have heard....There is a pneumatic bleeder that a friend of mine used to have and it was awesome. You hook it up like normal, crack the screw loose, and pull the trigger. It had a half gallon jug under neath and it would suck the entire line into the jug. Keep refilling the master and keep doing each corner. He showed me the first time and he was done with the bleeding in 15 minutes for the entire car. Here is one on the E-bag
Family owned 1969 Charger R/T DualQuad 440/727/GVO/3.55s
|
|
|
Re: Brake Bleeding Tool,,,,help,,,questions...
[Re: Pyper70]
#201288
01/22/09 09:23 PM
01/22/09 09:23 PM
|
Joined: Jan 2003
Posts: 6,531 Jacksonville, FL
Chris2581
master
|
master
Joined: Jan 2003
Posts: 6,531
Jacksonville, FL
|
I use the Vacula bleeding system and it does the job.If the bleed screws are too loose you will see a lot of air bubbles.
Nautilus Racing- We use Superformance gaskets and Turbo Action converters/products.
|
|
|
Re: Brake Bleeding Tool,,,,help,,,questions...
[Re: BSharp]
#201290
01/22/09 10:32 PM
01/22/09 10:32 PM
|
Joined: Sep 2005
Posts: 6,516 Santa Cruz, California
Lefty
master
|
master
Joined: Sep 2005
Posts: 6,516
Santa Cruz, California
|
Quote:
Get Speed Bleeders.
Try them and you'll never go back to "cave man" brake bleeding...
|
|
|
Re: Brake Bleeding Tool,,,,help,,,questions...
[Re: Leadfoot]
#201292
01/23/09 02:05 AM
01/23/09 02:05 AM
|
Joined: Nov 2003
Posts: 36,041 Lincoln Nebraska
RapidRobert
Circle Track
|
Circle Track
Joined: Nov 2003
Posts: 36,041
Lincoln Nebraska
|
Also I put a block of wood under the brake pedal so my helper doesn't push it(the pistons) past their normal length of travel into an unworn section of the bore.
live every 24 hour block of time like it's your last day on earth
|
|
|
Re: Brake Bleeding Tool,,,,help,,,questions...
[Re: Leadfoot]
#201293
01/23/09 10:10 AM
01/23/09 10:10 AM
|
Joined: Mar 2003
Posts: 15,493 the boonies
aarcuda
I Live Here
|
I Live Here
Joined: Mar 2003
Posts: 15,493
the boonies
|
Quote:
Just run a tube from the bleeder screw to a mason jar half full of brake fluid. Open the screw and pump the brakes slowly and do not let the reservoir run dry. Pumping will pump the air out and the tube stuck in the fluid will act as a check valve so nothing comes back in the lines. It's the preferred method for us people that don't have any friends.
but gravity bleeding also works (ie crack open the bleeder and let it drip for a few hours). the main concern is to make sure the master cylinder doesnt run dry or you have to bleed that and start all over again
|
|
|
Re: Brake Bleeding Tool,,,,help,,,questions...
[Re: BSharp]
#201294
01/23/09 01:54 PM
01/23/09 01:54 PM
|
Joined: Jan 2003
Posts: 10,030 Wisconsin
Aero426
I Live Here
|
I Live Here
Joined: Jan 2003
Posts: 10,030
Wisconsin
|
Quote:
Get Speed Bleeders.
These work really good if you are bleeding by yourself. I have them on two cars.
As mentioned, when bleeding, you only need the bleeder screw open just enough to get fluid and air out. Wobbly is too much.
I always insert the bleed hose into a jar with some brake fluid. With no speed bleeders, it will help prevent sucking air back in.
|
|
|
Re: Brake Bleeding Tool,,,,help,,,questions...
[Re: 69CHARGERMD]
#201295
01/23/09 08:28 PM
01/23/09 08:28 PM
|
Joined: Feb 2005
Posts: 28,312 Cincinnati, Ohio
Challenger 1
Too Many Posts
|
Too Many Posts
Joined: Feb 2005
Posts: 28,312
Cincinnati, Ohio
|
I use this pressure bleeder,It holds 1 gallon of brake fluid. Top part holds fluid with a rubber diaphan separating the lower half which is pressurized with about 20-30 psi of air. I just recently took it apart and repainted the top half after 20+ years of using it. The diapham inside was in great shape. I have master cyl adaptors for about 6 different master clys including the plastic resovour master clys. I recently replaced wheel clys on a boat trailer and I have a round multi thread cap that threads into the master cly up on the tonque of the trailer on surge brakes.I bled those new wheel clys in about 10 seconds per side and I was done. That's when I decided to clean it up after that job. Anyway it a failsafe way of doing it and it only takes a few minutes to hook it up. The cap adaptor shown is for cast iron dual master cyls like we use on our old mopars. My other mc adaptors are at work.It's great for flushing brake systems too. I store it with fluid in it pressurized with maybe 10 PSI. There's no air to get in there and spoil the brake fluid. So a gallon last me many jobs. [image]http://[/image]
Last edited by Challenger 1; 01/24/09 04:08 PM.
|
|
|
Re: Brake Bleeding Tool,,,,help,,,questions...
[Re: Leadfoot]
#201296
01/24/09 10:04 AM
01/24/09 10:04 AM
|
Anonymous
Unregistered
|
Anonymous
Unregistered
|
Quote:
Just run a tube from the bleeder screw to a mason jar half full of brake fluid. Open the screw and pump the brakes slowly and do not let the reservoir run dry. Pumping will pump the air out and the tube stuck in the fluid will act as a check valve so nothing comes back in the lines. It's the preferred method for us people that don't have any friends.
do it exactly like his way.save your money on those bleeders. start from farthest rear tire and then to next rear bleeder valve but keep adding fluid to your master cylinder,dont let it run dry. its also great to do this to remove any old nasty contaminated brake fluid.
|
|
|
Re: Brake Bleeding Tool,,,,help,,,questions...
#201297
01/24/09 10:35 AM
01/24/09 10:35 AM
|
Joined: Jan 2003
Posts: 4,852 KENTUCKY
69CHARGERMD
OP
master
|
OP
master
Joined: Jan 2003
Posts: 4,852
KENTUCKY
|
Thanks guys,,,,i am going to do it the old school way with some tubing and a mason jar,,fluid filled,,etc. This mityvac thing is a pain,,, i re-read the directions that come with it,,,and it actually says to START at the wheel closet to the MC,,,which is something i never heard of... I usually start at the tire furthest away,,,and work my way back... thanks,,, didnt expect all the "most excellent" responses....
|
|
|
Re: Brake Bleeding Tool,,,,help,,,questions...
[Re: Leadfoot]
#201298
01/24/09 12:49 PM
01/24/09 12:49 PM
|
Joined: Jan 2003
Posts: 1,279 Buzzardbreath Wyoming
BigBird
pro stock
|
pro stock
Joined: Jan 2003
Posts: 1,279
Buzzardbreath Wyoming
|
Quote:
Just run a tube from the bleeder screw to a mason jar half full of brake fluid. Open the screw and pump the brakes slowly and do not let the reservoir run dry. Pumping will pump the air out and the tube stuck in the fluid will act as a check valve so nothing comes back in the lines. It's the preferred method for us people that don't have any friends.
I have a little different version of this. I use a mason jar and use 2 tubes. One goes to a vacuum source (engine port usually). The other to the bleeder. Make sure the vacuum line is really long ( so you can reach any wheel ) and is just barely in the jar so you don't suck any brake fluid into the engine. Seal where the tubes go into the jar lid with silicon. Start the engine and crack the bleeder on the wheel and let the vacuum suck the fluid into the jar. Has worked for me for years.
|
|
|
|
|