Anybody have a lead on a 1/4" crank pulley spacer? - Moparts Forums

Register Log In Moparts Forums Unlawfl's Race & Engine Tech Anybody have a lead on a 1/4" crank pulley spacer?

Print Thread

Anybody have a lead on a 1/4" crank pulley spacer? #1782985 03/18/15 06:52 PM 03/18/15 06:52 PM
Joined: Feb 2014 Posts: 655 Huntsville, AL A Airwoofer OP mopar
Airwoofer OP mopar A Joined: Feb 2014 Posts: 655 Huntsville, AL	I need a good one (offset bolt, proper step/snaps) for my 540 to make the alternator line up. Can't move it w/o major hassle.

Re: Anybody have a lead on a 1/4" crank pulley spacer? [Re: Airwoofer] #1782986 03/18/15 06:58 PM 03/18/15 06:58 PM
Joined: Jan 2003 Posts: 25,877 Rio Linda, CA John_Kunkel Too Many Posts
John_Kunkel Too Many Posts Joined: Jan 2003 Posts: 25,877 Rio Linda, CA	Use two of these: http://arengineering.com/products/crank-pulley-spacer-0-125-thick-zinc-plated/ The INTERNET, the MISinformation superhighway

Re: Anybody have a lead on a 1/4" crank pulley spacer? [Re: Airwoofer] #1782987 03/18/15 07:01 PM 03/18/15 07:01 PM
Joined: May 2003 Posts: 1,751 Graham, WA P Polarapete top fuel
Polarapete top fuel P Joined: May 2003 Posts: 1,751 Graham, WA	Two of these should do it http://store.440source.com/Crank-Pulley-Shim-125-Thickness/productinfo/127-1005/ Good Luck. 1986 Dodge Ramcharger 440 2wd, Bracket Racer Under Construction 1998 Ram 2500 QuadCab, new daily driver. 2008 Honda Element 2014 Carry-On 7x14 Cargo Trailer

Re: Anybody have a lead on a 1/4" crank pulley spacer? [Re: Airwoofer] #1782988 03/18/15 07:43 PM 03/18/15 07:43 PM
Joined: Jan 2003 Posts: 31,050 Oregon A AndyF I Win
AndyF I Win A Joined: Jan 2003 Posts: 31,050 Oregon	If you want the machined step to center the pulley then you'll need to have a machine shop make one from billet. I sell a billet pulley spacer that is 3/8 thick for guys running one of my motor plates, but I don't sell a 1/4 inch stepped version.

Re: Anybody have a lead on a 1/4" crank pulley spacer? [Re: AndyF] #1782989 03/18/15 09:10 PM 03/18/15 09:10 PM
Joined: Jan 2003 Posts: 17,918 Akron, Ohio ProSport I Live Here
ProSport I Live Here Joined: Jan 2003 Posts: 17,918 Akron, Ohio	I have one with the machined step but it's 1/2" thick. You could have it cut down to 1/4". 8464266-20150318_190353.jpg (38 downloads) Last edited by ProSport; 03/18/15 09:30 PM.

Re: Anybody have a lead on a 1/4" crank pulley spacer? [Re: ProSport] #1782990 03/18/15 09:10 PM 03/18/15 09:10 PM
Joined: Jan 2003 Posts: 17,918 Akron, Ohio ProSport I Live Here
ProSport I Live Here Joined: Jan 2003 Posts: 17,918 Akron, Ohio	2 8464269-20150318_190411.jpg (35 downloads)

Re: Anybody have a lead on a 1/4" crank pulley spacer? [Re: Airwoofer] #1782991 03/18/15 11:47 PM 03/18/15 11:47 PM
Joined: Dec 2003 Posts: 22,696 Bitopia J jcc If you can't dazzle em with diamonds..
jcc If you can't dazzle em with diamonds.. J Joined: Dec 2003 Posts: 22,696 Bitopia	March Pulley has them, orderable thru Summit I blieve Reality check, that half the population is smarter then 50% of the people and it's a constantly contested fact.

Re: Anybody have a lead on a 1/4" crank pulley spacer? [Re: jcc] #1782992 03/19/15 12:20 AM 03/19/15 12:20 AM
Joined: Nov 2012 Posts: 60 Maryland G gofastboater member
gofastboater member G Joined: Nov 2012 Posts: 60 Maryland	I just had my machinist make me one. Cost me maybe $15.

Re: Anybody have a lead on a 1/4" crank pulley spacer? [Re: gofastboater] #1782993 03/19/15 02:40 AM 03/19/15 02:40 AM
Joined: Dec 2007 Posts: 12,588 Great Neck,LI,new york hemi-itis I Live Here
hemi-itis I Live Here Joined: Dec 2007 Posts: 12,588 Great Neck,LI,new york	Remember that MOPAR has a 2.25 register HEMI-ITIS has no cure. My condition is fully BLOWN!!

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To

Powered by UBB.threads™ PHP Forum Software 7.7.1