Re: Bring back the shine on a Carter AFB or Eddy Performer?
[Re: JohnRR]
#1646529
07/14/14 06:32 PM
07/14/14 06:32 PM
|
Joined: Jan 2003
Posts: 12,043 State of Confusion
hp383
OP
Just a normal tag again
|
OP
Just a normal tag again
Joined: Jan 2003
Posts: 12,043
State of Confusion
|
Its been so long since I bought the Carter AFB Competition Series that I must have forgotten. I thought I remembered it being shiny when I took it out of the box.
OK then, how about making the Eddys shine again than.
Join the Penguin Liberation Front!! Stop the Hippo Occupation!
|
|
|
Re: Bring back the shine on a Carter AFB or Eddy Performer?
[Re: BigBlockMopar]
#1646531
07/14/14 09:32 PM
07/14/14 09:32 PM
|
Joined: Jun 2012
Posts: 1,386 Philadelphia PA
Pynzo
Drugs are bad
|
Drugs are bad
Joined: Jun 2012
Posts: 1,386
Philadelphia PA
|
WD40 and a set of these brushes and elbow grease. All these carbs are aluminum but some Eddy's had a "Ball Burnished" finish that when new shined like chrome. Simply polished aluminum. These brushes can be found at home depot paint dept. They can reach the tight spots but for 4 carbs get at least 6 sets of brushes. They wear out quick. $4 a set I believe. A Hoppes pistol cleaning rod w/ .45 cal, .38 cal and .223 brushes also come in handy for the passages, and Hoppes powder solvent will break out any gum/bs and smell good too!
Last edited by Pynzo; 07/14/14 10:14 PM.
|
|
|
Re: Bring back the shine on a Carter AFB or Eddy Performer?
[Re: Pynzo]
#1646532
07/14/14 10:47 PM
07/14/14 10:47 PM
|
Joined: Jan 2003
Posts: 12,043 State of Confusion
hp383
OP
Just a normal tag again
|
OP
Just a normal tag again
Joined: Jan 2003
Posts: 12,043
State of Confusion
|
I love the smell of the Hoppes. I sometimes dab some on a paper towel and use it as air freshener.
Join the Penguin Liberation Front!! Stop the Hippo Occupation!
|
|
|
Re: Bring back the shine on a Carter AFB or Eddy Performer?
[Re: hp383]
#1646533
07/14/14 10:55 PM
07/14/14 10:55 PM
|
Joined: Apr 2012
Posts: 18,880 -
RSNOMO
Moparts Torchbearer
|
Moparts Torchbearer
Joined: Apr 2012
Posts: 18,880
-
|
|
|
|
Re: Bring back the shine on a Carter AFB or Eddy Performer?
[Re: Pynzo]
#1646535
07/14/14 11:19 PM
07/14/14 11:19 PM
|
Joined: Jul 2013
Posts: 1,272 Northern Calyfornua
Sxrxrnr
pro stock
|
pro stock
Joined: Jul 2013
Posts: 1,272
Northern Calyfornua
|
Quote:
WD40 and a set of these brushes and elbow grease. All these carbs are aluminum but some Eddy's had a "Ball Burnished" finish that when new shined like chrome. Simply polished aluminum. These brushes can be found at home depot paint dept. They can reach the tight spots but for 4 carbs get at least 6 sets of brushes. They wear out quick. $4 a set I believe. A Hoppes pistol cleaning rod w/ .45 cal, .38 cal and .223 brushes also come in handy for the passages, and Hoppes powder solvent will break out any gum/bs and smell good too!
Once had my newly ceramic coated TTI headers almost destroyed by a substantial rear main seal leak and had almost 200 miles that I had to drive before able to resolve leak.
Coated with oil on collectors that baked on like the worst oven you had ever seen. Used these steel and brass brushes using Flitz and Mothers aluminum polishes.
Headers came out perfect with no apparent damage,,,,did take a few hours of scrubbing however. I have before and after photos if anyone cares to see.
|
|
|
Re: Bring back the shine on a Carter AFB or Eddy Performer?
[Re: hp383]
#1646537
07/15/14 01:33 PM
07/15/14 01:33 PM
|
Joined: Nov 2004
Posts: 3,544 Syracuse,NY
CompWedgeEngines
master
|
master
Joined: Nov 2004
Posts: 3,544
Syracuse,NY
|
Yes, there were Competition series Carters with a shiny finish.,...your not going crazy....
RIP Monte Smith
Your work is a reflection of yourself, autograph it with quality.
WD for Diamond Pistons,Sidewinder cylinder heads, Wiseco, K1 rods and cranks,BAM lifters, Morel lifters, Molnar Technologies, Harland Sharp, Pro Gear, Cometic, King Engine Bearings and many others.
|
|
|
Re: Bring back the shine on a Carter AFB or Eddy Performer?
[Re: Pynzo]
#1646538
07/15/14 03:46 PM
07/15/14 03:46 PM
|
Joined: Aug 2008
Posts: 1,568 Omaha, Nebraska
Scott Carl
pro stock
|
pro stock
Joined: Aug 2008
Posts: 1,568
Omaha, Nebraska
|
Quote:
WD40 and a set of these brushes and elbow grease. All these carbs are aluminum but some Eddy's had a "Ball Burnished" finish that when new shined like chrome. Simply polished aluminum. These brushes can be found at home depot paint dept. They can reach the tight spots but for 4 carbs get at least 6 sets of brushes. They wear out quick. $4 a set I believe. A Hoppes pistol cleaning rod w/ .45 cal, .38 cal and .223 brushes also come in handy for the passages, and Hoppes powder solvent will break out any gum/bs and smell good too!
on the use of bore brushes. Worked a treat on my badly stored AVS
|
|
|
Re: Bring back the shine on a Carter AFB or Eddy Performer?
[Re: RSNOMO]
#1646541
07/15/14 05:12 PM
07/15/14 05:12 PM
|
Joined: Jan 2003
Posts: 75,017 U.S.S.A.
JohnRR
I Win
|
I Win
Joined: Jan 2003
Posts: 75,017
U.S.S.A.
|
Quote:
I was on the fence initially...
But I'll tell ya'...
Got one on top of a 440...
It's been there 15+ years...
With very minimal effort, it still looks new...
I'm a believer...
I prefer the factory look and they don't look factory to me.
|
|
|
|
|