horsepower estimate - Moparts Forums

Register Log In Moparts Forums Unlawfl's Race & Engine Tech horsepower estimate

Print Thread

horsepower estimate #1413686 04/02/13 02:56 PM 04/02/13 02:56 PM
Joined: Jan 2003 Posts: 1,008 wv D Dartcuda OP super stock
Dartcuda OP super stock D Joined: Jan 2003 Posts: 1,008 wv	Best guess this combo. Early 360 block with Scat 4" stroker kit at 10.5 to 1 compression . Comp Cams hydraulic flat tappet XE-295HL , 251-257 @.050" W/Harland Sharp 1.5 rockers. SDSS stage 2 Edelbrocks , flow 285 @ .500" Ported air gap , holley 950 HP and TTI 1-5/8"-1-3?4 step headers.

Re: horsepower estimate [Re: Dartcuda] #1413687 04/02/13 05:44 PM 04/02/13 05:44 PM
Joined: Aug 2006 Posts: 2,141 junction city oregon V viperblue72 top fuel
viperblue72 top fuel V Joined: Aug 2006 Posts: 2,141 junction city oregon	I'd say 475 horsepower.

Re: horsepower estimate [Re: Dartcuda] #1413688 04/02/13 05:49 PM 04/02/13 05:49 PM
Joined: Jan 2003 Posts: 6,266 Renton Washington T Triple Threat master
Triple Threat master T Joined: Jan 2003 Posts: 6,266 Renton Washington	https://board.moparts.org/ubbthreads/show...rt=all&vc=1 Your heads are a bit better than the RHS's. Should run strong. -Dustin 67 Dart, 9 second, 392" G3 Hemi 68 Barracuda 340 F/SA

Re: horsepower estimate [Re: Dartcuda] #1413689 04/02/13 06:37 PM 04/02/13 06:37 PM
Joined: Feb 2005 Posts: 20,163 PA. pittsburghracer "Little"John
pittsburghracer "Little"John Joined: Feb 2005 Posts: 20,163 PA.	Quote: Best guess this combo. Early 360 block with Scat 4" stroker kit at 10.5 to 1 compression . Comp Cams hydraulic flat tappet XE-295HL , 251-257 @.050" W/Harland Sharp 1.5 rockers. SDSS stage 2 Edelbrocks , flow 285 @ .500" Ported air gap , holley 950 HP and TTI 1-5/8"-1-3?4 step headers. Ryan's stage 2 don't flow 285@500 This is copied from his website for stage 4 and a 2.05 valve. EDELBROCK STAGE 4 PORT WORK LIFT------IN/EX .100"----76.0/N/A .200"--147.0/112.1 .300"--206.7/163.9 .400"--255.3/193.2 .450"--274.3/203.6 .500"--279.0/212.2 .550"--285.0/218.0 .600"--293.2/226.3 .650"--293.2/229.4 .700"--293.2/230.8 All #'s at 28" of H20. Ported head was flowed with 2.05" FERREA valve with 30 degree back cut on intake valve, and no flow tube on exhaust. 1970 Duster Edelbrock headed 408 5.984@112.52 422 Indy headed small block 5.982@112.56 mph 9.42@138.27 Livin and lovin life one day at a time

Re: horsepower estimate [Re: Dartcuda] #1413690 04/02/13 06:39 PM 04/02/13 06:39 PM
Joined: Jul 2012 Posts: 429 Washington skrews mopar
skrews mopar Joined: Jul 2012 Posts: 429 Washington	520ish

Re: horsepower estimate [Re: skrews] #1413691 04/02/13 10:12 PM 04/02/13 10:12 PM
Joined: Jan 2003 Posts: 1,008 wv D Dartcuda OP super stock
Dartcuda OP super stock D Joined: Jan 2003 Posts: 1,008 wv	Sorry , had to dig out Ryans stage 2 flow chart. so 285 @ .550 .100--71.2 .200--143.8/107.1 .300--198.3/148.7 .400--242.0/189.6 .450--254.1/203.1 .500--272.5/208.6 .550--284.7/211.3 .600--287.8/214.7

Re: horsepower estimate [Re: Dartcuda] #1413692 04/02/13 10:17 PM 04/02/13 10:17 PM
Joined: Jan 2003 Posts: 1,008 wv D Dartcuda OP super stock
Dartcuda OP super stock D Joined: Jan 2003 Posts: 1,008 wv	I was hoping for 500

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To

Powered by UBB.threads™ PHP Forum Software 7.7.1