PVC location question - Moparts Forums

Register Log In Moparts Forums Moparts Question and Answer PVC location question

Print Thread

PVC location question #1178241 02/14/12 01:36 PM 02/14/12 01:36 PM
Joined: Mar 2007 Posts: 12,008 Finally a HUSKER again Moparnut426 OP I Live Here
Moparnut426 OP I Live Here Joined: Mar 2007 Posts: 12,008 Finally a HUSKER again	This may seem like a dumb question for some of you guys, but on a 69 sixpack intake, where does the pvc valve hook up to? and on whick side is the pvc valve cover go on? Im thinking its the back of the intake, and the vc goes on the drivers side, but I can not confirm that. Kasey

Re: PVC location question [Re: Moparnut426] #1178242 02/14/12 01:44 PM 02/14/12 01:44 PM
Joined: Jan 2004 Posts: 27,347 Today? Who Knows? 1_WILD_RT Management Trainee
1_WILD_RT Management Trainee Joined: Jan 2004 Posts: 27,347 Today? Who Knows?	PVC is located in the plumbing aisle... PCV plugs into the passenger side of the center carb... "The Armies of our ancestors were lucky, in that they were not trailed by a second army of pencil pushers."

Re: PVC location question [Re: 1_WILD_RT] #1178243 02/14/12 02:03 PM 02/14/12 02:03 PM
Joined: Oct 2011 Posts: 32 MA S stumble bee member
stumble bee member S Joined: Oct 2011 Posts: 32 MA	'69 valve covers,the oil fill goes on the drivers side front segment and the PCV valve goes on the pass side rear segment

Re: PVC location question [Re: Moparnut426] #1178244 02/14/12 02:19 PM 02/14/12 02:19 PM
Joined: Dec 2005 Posts: 799 Missouri B bb74swngr mopar addict
bb74swngr mopar addict B Joined: Dec 2005 Posts: 799 Missouri	Kasey, I hope it is okay to ask this in your thread. How important is it to have a PCV valve in addition to the crank case breather that is plumbed to the air cleaner? Can the PCV be eliminated on an older street driven car? BigBlock 74 Swinger

Re: PVC location question [Re: bb74swngr] #1178245 02/14/12 02:41 PM 02/14/12 02:41 PM
Joined: Oct 2011 Posts: 32 MA S stumble bee member
stumble bee member S Joined: Oct 2011 Posts: 32 MA	I think you should run a PCV valve, too much crank case pressure can cause gasket oil leaks everywhere, also you could have better ring seal with positive crankcase ventilation

Re: PVC location question [Re: 1_WILD_RT] #1178246 02/14/12 03:11 PM 02/14/12 03:11 PM
Joined: Mar 2007 Posts: 12,008 Finally a HUSKER again Moparnut426 OP I Live Here
Moparnut426 OP I Live Here Joined: Mar 2007 Posts: 12,008 Finally a HUSKER again	LOL,,, Sorry for the bad case of dyslexia. And spelling.... And thanks, I know there is a plug on the back of the intake, and it looks like its for a vacum tree. Also this is a 70 set up on a 69 engine, and well its going in a 88 rancharger. But I want it to look correct, and function properly. Thanks again guys. KAsey

Re: PVC location question [Re: stumble bee] #1178247 02/14/12 03:12 PM 02/14/12 03:12 PM
Joined: Dec 2005 Posts: 799 Missouri B bb74swngr mopar addict
bb74swngr mopar addict B Joined: Dec 2005 Posts: 799 Missouri	Thank you Shawn. I was really hoping for a different answer, but I am sure you're right...darn it:) Thank you. BigBlock 74 Swinger

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To

Powered by UBB.threads™ PHP Forum Software 7.7.1