Need a little help with an Ultra Bell Install, easy one - Moparts Forums

Register Log In Moparts Forums Unlawfl's Race & Engine Tech Need a little help with an Ultra Bell Install, easy one

Print Thread

Need a little help with an Ultra Bell Install, easy one #1141990 12/22/11 06:34 PM 12/22/11 06:34 PM
Joined: Feb 2008 Posts: 70 MN M mkvien OP member
mkvien OP member M Joined: Feb 2008 Posts: 70 MN	I got all done cutting and installing my Ultra Bell on a 727 and realized that I left this part out, it was originally installed on the top two bolts of the pump housing, do I need to tear it apart and install this? What does it do? Thanks guys...

Re: Need a little help with an Ultra Bell Install, easy one [Re: mkvien] #1141991 12/22/11 06:48 PM 12/22/11 06:48 PM
Joined: Oct 2010 Posts: 2,407 Ambridge, Pa. R rickraw top fuel
rickraw top fuel R Joined: Oct 2010 Posts: 2,407 Ambridge, Pa.	that is the cover for the vent. put it on. merryxmas. seeya.

Re: Need a little help with an Ultra Bell Install, easy one [Re: mkvien] #1141992 12/22/11 06:49 PM 12/22/11 06:49 PM
Joined: Jan 2003 Posts: 1,606 westerly, ri. usa 4 440lebaron top fuel
440lebaron top fuel 4 Joined: Jan 2003 Posts: 1,606 westerly, ri. usa	hello, cover for vent in oil pump housing, most plug it and vent from rear. i tapped mine for 1/8 pipe plug gary all parts are sold as is, all parts are considered used no warranties or returns paypal/check/money order, shipping is from zip 02891, buyer pays paypal fees 24% IRS 1099A plus 3% of part price, check/money order preferred site is not monitored 24/7 there might be a delay in response

Re: Need a little help with an Ultra Bell Install, easy one [Re: 440lebaron] #1141993 12/22/11 09:19 PM 12/22/11 09:19 PM
Joined: Mar 2006 Posts: 9,910 Eighty Four, PA B G Racing master
B G Racing master Joined: Mar 2006 Posts: 9,910 Eighty Four, PA	Quote: hello, cover for vent in oil pump housing, most plug it and vent from rear. i tapped mine for 1/8 pipe plug gary [IMG]http://i430.photobucket.com/albums/qq21/ajcasini/max_zpsdppwd9km.jpg[/IMG]

Re: Need a little help with an Ultra Bell Install, easy one [Re: B G Racing] #1141994 12/28/11 12:22 PM 12/28/11 12:22 PM
Joined: Feb 2008 Posts: 70 MN M mkvien OP member
mkvien OP member M Joined: Feb 2008 Posts: 70 MN	Back in the shop after spending some family time... The new bell covers that hole completely, or at least the direct line of sight. There is an air gap back there so it can vent. Installing that cover will act as a shim, I believe, causing misalignment of the transmission, any further comments?

Re: Need a little help with an Ultra Bell Install, easy one [Re: mkvien] #1141995 12/28/11 07:23 PM 12/28/11 07:23 PM
Joined: Oct 2010 Posts: 2,407 Ambridge, Pa. R rickraw top fuel
rickraw top fuel R Joined: Oct 2010 Posts: 2,407 Ambridge, Pa.	pull the support, diss the pump, tap the vent hole- make sure the pipe plug is flush outside & inside. put the vent on top of the tail shaft housing in the middle, towards the front of the hsg. i put in a 1/8 pipe 90 & ran a hose up to the firewall & put the vent there. never had a problem. seeya.

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To

Powered by UBB.threads™ PHP Forum Software 7.7.1