Bearing ? - Moparts Forums

Register Log In Moparts Forums Unlawfl's Race & Engine Tech Bearing ?

Print Thread

Bearing ? #841531 10/29/10 12:12 PM 10/29/10 12:12 PM
Joined: Apr 2007 Posts: 159 Vidor Texas O onyxba OP member
onyxba OP member O Joined: Apr 2007 Posts: 159 Vidor Texas	What bearings would you use in a turbo application. What about coatings on bearings. Thanks Brian W.

Re: Bearing ? [Re: onyxba] #841532 10/29/10 04:43 PM 10/29/10 04:43 PM
Joined: Jan 2003 Posts: 28,069 Irving, TX feets Senior Management
feets Senior Management Joined: Jan 2003 Posts: 28,069 Irving, TX	There are lots of bearings in cars. Can you be a wee bit more specific? We are brothers and sisters doing time on the planet for better or worse. I'll take the better, if you don't mind. - Stu Harmon

Re: Bearing ? [Re: feets] #841533 10/29/10 06:51 PM 10/29/10 06:51 PM
Joined: Apr 2007 Posts: 159 Vidor Texas O onyxba OP member
onyxba OP member O Joined: Apr 2007 Posts: 159 Vidor Texas	Rod and main bearing to be more specific. What brand and what coating, bimetal trimetal all aluminum any other that may be available to be used in a turbo application. thanks for the reply. Brian W.

Re: Bearing ? [Re: onyxba] #841534 10/29/10 09:36 PM 10/29/10 09:36 PM
Joined: Sep 2005 Posts: 549 Chicagoland chargerron69 mopar
chargerron69 mopar Joined: Sep 2005 Posts: 549 Chicagoland	i think what feets was trying to say is, what engine are you building? 67 Coronet 383 hogged out 906's 727 430 dana best 10.48 @126.80 1.47 60 on fogger same car pump gas 605 wedge 9.98 @ 138.42 1.50 60 on wore out 9 inch radial slick ss springs and frame connectors its got more in it!!! 72 Newport 2 door 400 727 85 Ram 440 4 speed O/D 3.54 dana

Re: Bearing ? [Re: chargerron69] #841535 10/30/10 11:12 AM 10/30/10 11:12 AM
Joined: Jan 2003 Posts: 28,069 Irving, TX feets Senior Management
feets Senior Management Joined: Jan 2003 Posts: 28,069 Irving, TX	What feets was trying to say was which bearings? Turbo, main, rod, cam, wheel, pilot, etc. We are brothers and sisters doing time on the planet for better or worse. I'll take the better, if you don't mind. - Stu Harmon

Re: Bearing ? [Re: feets] #841536 10/30/10 12:59 PM 10/30/10 12:59 PM
Joined: Apr 2007 Posts: 159 Vidor Texas O onyxba OP member
onyxba OP member O Joined: Apr 2007 Posts: 159 Vidor Texas	What onyxba said in second post was rod and main bearings, to be specific didn't know a decoder ring was needed. Sorry for the question i asked. Did not give engine description as i was asking as a general rule of thumb at to what bearing is recommended for a turbocharger application? Brian W.

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To

Powered by UBB.threads™ PHP Forum Software 7.7.1