360 intake - Moparts Forums

Register Log In Moparts Forums Moparts Question and Answer 360 intake

Print Thread

360 intake #790708 09/02/10 01:18 PM 09/02/10 01:18 PM
Joined: Jun 2009 Posts: 252 New York J jagrunt551 OP enthusiast
jagrunt551 OP enthusiast J Joined: Jun 2009 Posts: 252 New York	Anyone used the Crosswind intake? I know it's made in China, but is it any good? Thanks

Re: 360 intake [Re: jagrunt551] #790709 09/02/10 03:57 PM 09/02/10 03:57 PM
Joined: Nov 2003 Posts: 36,041 Lincoln Nebraska R RapidRobert Circle Track
RapidRobert Circle Track R Joined: Nov 2003 Posts: 36,041 Lincoln Nebraska	Haven't used it personally but was going to but it has 340/360 large ports and I wanted a smaller intake port to better match my mag heads. I hear the early ones had QC probs but that that has been pretty much resolved. The price is right and everything (pretty much) is made over there so I would have no prob ordering one live every 24 hour block of time like it's your last day on earth

Re: 360 intake [Re: jagrunt551] #790710 09/02/10 09:55 PM 09/02/10 09:55 PM
Joined: Nov 2004 Posts: 2,495 Oregon City, OR Baxter61 top fuel
Baxter61 top fuel Joined: Nov 2004 Posts: 2,495 Oregon City, OR	Quote: I know it's made in China, but is it any good? doesnt this question kinda answer itself

Re: 360 intake [Re: Baxter61] #790711 09/03/10 12:02 AM 09/03/10 12:02 AM
Joined: Dec 2009 Posts: 1,074 detroit, mi POS Dakota super stock
POS Dakota super stock Joined: Dec 2009 Posts: 1,074 detroit, mi	Quote: Quote: I know it's made in China, but is it any good? doesnt this question kinda answer itself No, it doesn't. It's a good intake for those who dont wish to pay an extra 100 plus bucks for a fancy logo. It fits on an LA or a magnum too. The port alignment is pretty good. The bolt holes might be a tad large necessitating you to be mindful of how it sits when you torque it down. Overall I like it! I hope there is a single plane design to follow. If other manufacturers feel rubbed the wrong way by this, then good! They should compete instead of being crooks.

Re: 360 intake [Re: POS Dakota] #790712 09/03/10 12:43 AM 09/03/10 12:43 AM
Joined: Mar 2005 Posts: 862 Iowa State fan kilroy super stock
kilroy super stock Joined: Mar 2005 Posts: 862 Iowa State fan	Thats crap attitude. If you think the only diff is the 100 try a snapon/craftsman/kt tool vs the cheap china tool see which works better. Besides think its a coincidence that the cheapy intakes look exactly like the eddy or others? rip off in more ways than one. 1973 Charger, former SE, former auto I'm not trying to be difficult, it comes naturally....

Re: 360 intake [Re: jagrunt551] #790713 09/03/10 12:45 AM 09/03/10 12:45 AM
Joined: Mar 2005 Posts: 862 Iowa State fan kilroy super stock
kilroy super stock Joined: Mar 2005 Posts: 862 Iowa State fan	Quote: Anyone used the Crosswind intake? I know it's made in China, but is it any good? Thanks Sorry dude to jack thread on previous post. No I havent used one not sure how they run but have held one and looked at one personally and the cast was lower quailty and alignment didnt look good. 1973 Charger, former SE, former auto I'm not trying to be difficult, it comes naturally....

Re: 360 intake [Re: kilroy] #790714 09/03/10 05:20 AM 09/03/10 05:20 AM
Joined: Jun 2007 Posts: 1,161 Mississippi M Mr. T super stock
Mr. T super stock M Joined: Jun 2007 Posts: 1,161 Mississippi	You would probably be better off if you could find a used Edelbrock. I have never seen a product that was manufactured in China, Vietnam, or Mexico that has as high of standards as American made products. Sadly, my job depends upon imports.

Re: 360 intake [Re: Mr. T] #790715 09/03/10 11:31 AM 09/03/10 11:31 AM
Joined: May 2003 Posts: 15,487 Florida S scratchnfotraction I Live Here
scratchnfotraction I Live Here S Joined: May 2003 Posts: 15,487 Florida	IMHO any LD4B or LD340 intake is right on par with and airgap rpm intake old skool but still ranks up there in the #s shoot out i like my LD4B on the 318 over any intake I have had so far have not had a airgap.but have put a couple on and have seen the improvment it made though

Re: 360 intake [Re: POS Dakota] #790716 09/03/10 12:04 PM 09/03/10 12:04 PM
Joined: Nov 2004 Posts: 2,495 Oregon City, OR Baxter61 top fuel
Baxter61 top fuel Joined: Nov 2004 Posts: 2,495 Oregon City, OR	Quote: Quote: Quote: I know it's made in China, but is it any good? doesnt this question kinda answer itself No, it doesn't. It's a good intake for those who dont wish to pay an extra 100 plus bucks for a fancy logo. Because when you buy some name brand stuff thats all your paying for is a logo. Not research and development or anything like that. Any retard can just go out and cast their own manifold and it works like it should, right?

Moderated by Al_Alguire, Hotwheelsjr, moparts, not_a_charger, RangerDan440, tboomer

Hop To

Powered by UBB.threads™ PHP Forum Software 7.7.1