(SOLD)

AutoMeter Level 1 External Digital Pro Shift Light Part# ATM-5343

Works and looks excellent. Had a very small crack on mount base (not an issue, but see last photo), crack is repaired. Only selling due to digital dash has an internal shift light. Located in Arizona.

Comes with instructions. Retails for $185 at Summit or JEGS, etc.

https://www.summitracing.com/parts/atm-5343

$85 shipped in the U.S. Accept PayPal, check or money order.

PM me if you want it. Thanks Moparts!

((SOLD)

Our universal leaf spring buckets allow you to lower the front spring eye height on your current leaf spring setup for lower ride height and adjustability. Aftermarket buckets are also designed to provide more strength and rigidity when welded in and gusseted to your cage with bars. A stronger front leaf spring mount will yield better 60ft times are the spring/Cal Trac/ Traction Device has a rigid push point with no flex.

Universal Design
Some Traction Devices May only Utilize 3 of 4 Holes Provided
Installation Requires Cutting Factory Sheetmetal
Installation Requires Part To Weld In
Bracing/Bars To Boxes Suggested For Strength – Better 60 Ft Times
Does Not Include Hardware

Innovative Racecraft
$200 shipped lower 48 states
John 586-222-2728 or pm

Richmond R&P 4.56 for Dana 60
P/N 69-0053-1
New in box
$300 shipped lower 48 states
John 586-222-2728 or pm

CR12B early B-body fuel tank, has sump box welded in, sump box is about 1" below tank with 4" to 5" tall inside tank. Tank was coated inside and out by a company called Tank Renu. here is a link.
https://www.gastankrenu.com/
Also has Aeromotive fuel filter with -10 outlet, -8 return,-6 vent. Also, can use a stock pickup, I have a new one to go with it. to plug the hole where it goes.
400$
Prefer local pick up, will ship at buyer's expense, I think it would be pretty expensive though.
Located in Kansas City area.
Pm if interested.

Used MSD 2-Step Part#8739. Asking $40.00 plus shipping. Located in Ohio 43612. PM if interested

Brand new - box still sealed.

Aeromotive A1000 electric fuel pump.

Located in Arizona.

Accept PayPal, Check or Money Order for payment.
$350 PayPal - Goods & Services (3% fees)
$350 PayPal - Friends & Family (no fees).
$350 Check or Money Order.

Ships when funds clear.

PM me if you want it. Thanks Moparts!

Autometer Sport Comp II tachometer and gauges. Included are a 3690 tachometer with shift light and 3692 volt, 3637 water temp and 3627 oil pressure gauges. The gauges are all electrical gauges. I bought these for a car I used to own but sold the car before ever using them. $450 for everything. Selling as a package only.

gt340 at yahoo.com

Howard's solid flat tappet cam for Mopar big blocks, part number CL722322-08. See links below for specifications. I bought this cam for my engine with the intention of taking the car to the track when the car was finished being restored along with the engine being built but I have changed my mind about racing the car and decided to go with a milder hydraulic cam instead. I had this cam installed in my engine on the engine stand but it never was run and is essentially new. $375 + shipping. I also have a new set of Comp Cams 973-16 inner valve springs I was going to use with this cam and Edelbrock RPM heads that I am asking $40 for.

https://www.summitracing.com/parts/HRS-CL722322-08

https://www.summitracing.com/parts/cca-973-16

gt340 at yahoo.com

Never used Cheetah Shifter 70001B with cover. I was planning on converting my Dart from a 4-speed to an automatic and bought this shifter to use. I have decided however to leave the car a 4-speed so I have no need for the shifter. I took it out of the box and set it with the cover over it on the hump in my car to see what it would look like but that's the only time it's been out of the box other than for the pictures. $500 including the cover.

gt340 at yahoo.com

Rear trailer tie down brackets for most A, B, or E body vehicles (doesn’t fit the 7 ¼ rear axle). These piggyback onto the bottom of the stock shock plate mounting nuts and then 4 more nuts hold these tie down brackets on. You must have enough extra thread hanging down on the bottom of your U-bolts to fit the ¼” thick tie down bracket and another nut. No disassembly necessary, just slide the brackets over the extra thread on your U-bolts, install the included nuts, tighten them down and you’re done. Takes about 10 minutes to install. These eliminate all the hassles that come with using axle straps. Fits A, B, and E body cars with the standard shock plates like shown in the pictures. $60.00 per pair plus shipping. I also have these available for cars with CalTracs, same price. Made in the USA.
Email mrrandyj@aol.com

Cleaning out the shelves and have some electronics for sale. All the stuff was installed in a car but none of it was ever used. All was working when removed. PM me here, text/call at 7 zero 7 9 8 zero 2 one 6 7

First part is an MSD 8970 3 stage retard. $275 obo




Next Biondo Mega 200 delay box $200 obo



Edelbrock 41900 nitrous controller $400 obo



Next is an NX Nitrous controller and MSD Window switch $300 oboi

Rebuilt Carter Competition Series 9625SA 625cfm AFB 4bbl carb with electric choke. Performance carb prior to the Edelbrock Performer. Date code A1.

$250 plus shipping

PM or call 5zero7-373-59zero7 days. No texts

Moroso Breather Tank, catch can part # 85465, 1 qt., Round, Aluminum, Natural, Filtered Breather, Mounting Bracket, Petcock. New Never Used. $75 rich1981@optonline.net

Used GZ Motorsports vacuum pump with 12AN fittings and billet aluminum pulley. No history on it as it came with an engine purchase. Very clean and no apparent damage, just don't need. No brackets, was mounted on a motor plate.

New they're $650, will take $350 + shipping

PM or call 5zero7-373-59zero7 days. Sorry, no texts

Cross posted

I have a couple sets of new ductile iron main caps available for main journals 1 through 4. These are Mopar Performance caps. The center 3 caps are 4 bolt main. These are the same caps that came standard on R3 4 bolt blocks. I have installed these caps on small blocks before by milling off the ends of the center caps to leave them 2 bolt. See pictures for the 3 modified center caps installed on a 340 stroker engine. These caps are more stout than the stock 360 or magnum engine caps and are an excellent upgrade for any high performance build. A line bore will be needed when installing new caps as well as some machining for the thrust bearing on the #3. You can use your stock engine #5 cap.

Price is $300 shipped per set in the lower 48 states. I will ship internationally for the additional cost.

Email procketrichard@hotmail.com for more information.

For sale is a new P4532598 Mopar Performance single plane intake manifold that fits Mopar W7, W8 & W9 small block cylinder heads. This manifold is designed to be used on short deck aftermarket blocks. No modifications to the ports or plenum have been performed.
Price is $500 shipped in the lower 48 states. I will ship internationally for the extra cost.

Contact procketrichard@hotmail.com for more information and pictures.

New Mopar Performance W2 /W5 exhaust roller rockers. I have several of these so if you need more than one just ask.

Price is $40 each shipped in the lower 48 states.
Set of eight rockers is $280 shipped in the lower 48 states.

I will ship internationally for the additional cost.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

I have a new PRW 1.6 ratio roller rocker arm kit containing all parts needed to install these rocker arms including steel bushed rocker arms, rocker arm shafts, spacers, shims, adjusters, steel shaft hold downs and hold down hardware. This kit is new in the box and is PRW part # 3231812.

Price is $495 shipped in the lower 48 states.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

I have a new set of 8 Mopar Performance pistons and wrist pins Mopar part# P4876973 for a 3.454” stroke crankshaft. Specs are 4.060” bore, 1/16, 1/16, 3/16 ring set, 0.984” wrist pin, flat top with ~ 5 cc eyebrows, listed by Mopar as 10.5 compression ratio. Compression height is ~ 1.72” per my measurement.

Price for the set is $480 shipped in the lower 48 states. I will ship internationally for the extra cost.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

I have a set of New BRC 4.030" forged flat top pistons and pins for a 3.79" stroke small block crankshaft. Compression height is ~ 1.57" and the ring lands are 1/16, 1/16 and 3/16. Pins are 0.984”. Approximately 6cc valve reliefs.

These pistons can be used in aftermarket race blocks or stock 360/5.9 magnum engine blocks with 4.030” finished bores.

Price is $475 shipped in the lower 48 states. I will ship elsewhere for the added cost.

I have a new SCAT forged rotating assembly for 360 & 5.9 Magnum Mopar engines. All parts are new high-quality parts. Final cubic inches will be 408”.
The assembly includes the following parts.

• SCAT forged 4.000” crankshaft part # 4-360-4000-6123
• SCAT forged H-beam connecting rods with APR 2000 bolts part # 2-360-6123-2124A
• Diamond Forged flattop 4.030” bore pistons (0.030” oversize) part # 51026
• Trend wrist pins - 0.984” part # TPD-G9842750155
• Diamond wrist pin locks
• Mahle file fit ring set with Moly ductile iron top rings part # MAH4035MS
• Speed Pro Tri metal Competition Series rod bearings part # 8-7125CH
• Clevite P-Series full groove main bearings part # MS-1266P

If you are looking for a 360 stroker with lower compression, I can substitute the pistons and connecting rods for new SRP 4.030” dished pistons part # 220156 (16.9 cc piston head volume) and new Eagle H-beam rods part # CRS6123C3D (360 stroker assembly only).

These rotating assemblies will need balancing.

The price for this complete kit with the Diamond flat top pistons and SCAT rods is $2,750 plus shipping cost.

The price for this complete kit with the SRP dished pistons and the Eagle H-beam rods is $2,600 plus shipping cost.

I can also meet in CT.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

I have a new SCAT forged rotating assembly for 340 Mopar engines. All parts are new high-quality parts. Final cubic inches will be 414”.
The assembly includes the following parts.

• SCAT forged 4.000” crankshaft part # 4-340-4000-6123
• SCAT forged H-beam connecting rods with APR 2000 bolts part # 2-360-6123-2124A
• Diamond Forged flattop 4.060” bore pistons (0.020” oversize) part # 51028
• Trend wrist pins part # TPD-G9842750155
• Diamond wrist pin locks
• Perfect Circle file fit ring set with Moly ductile iron top rings part # 315-0036.065
• Speed Pro Tri metal Competition Series rod bearings part # 8-7125CH
• Clevite P-Series full groove main bearings part # MS-1344P

This rotating assembly will need balancing.

Price for this complete kit is $2,750 plus shipping cost.

I can also meet in CT.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

I have a new T&D rocker arm and shaft kit for W2 Econo cylinder heads that have the cast in pedestals. T&D part # 8100. Rocker ratio is 1.5. Includes the rockers, shafts, spacers and bolts.

Price is $1250 plus shipping. I will ship internationally.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

I have a new Big Block Lunati solid roller cam part # 40230912 & solid roller lifters part # 72451-16. The specs of the cam are as follows:
Part # 40230912
Basic Operating RPM Range: 4,500-7,500
Duration at 050 inch Lift: 276 int./284 exh.
Advertised Duration: 312 int./320 exh.
Valve Lift with Factory Rocker Ratio: 0.690 int./0.690 exh.
Lobe Separation Angle 106
Camshaft Gear Attachment: 3-bolt
Valve Lash: 0.026 in. Intake 0.028 in. Exhaust

Lifter Specs and Description are as follows:
Part # 72451-16
Fits Engines 361-440
Lifter Diameter 0.903"
Weight – Lifter Pair 256 grams
Seat Height 1.98"
Pressurized Oiling to Roller Bearings - Yes
Pushrod oiling - Yes
Lifter Wheel Diameter 0.81”

Developed for serious racing applications, the pressurized oiling system of these lifters provides constant lubrication through the axle and to the needles. This reduces wear in the axle and increases the durability of the lifter. Also, for increased durability, all surfaces are hardened and polished, which makes the body stronger and smoother while reducing friction. The solid vertical bar roller lifters with pressurized oiling are held to higher standards than the competition for the ultimate in race lifters

Was planning to build a big block bracket engine but plans have changed so these are no longer needed. I have not opened the lifter package as it is one of those plastic packages is like Howards lifters and usually breaks and never stays shut on its own afterwards. Picture of lifter pair is what was on a retailers website.

Price for the cam and lifters is $1,250 plus $35 shipping in the lower 48 states.

Email me at procketrichard@hotmail.com for more pictures or any questions.

I have a 440 six pack center carb part # 4144-1 that was factory reconditioned by Holley. Has not been run since reconditioned.

$750 shipped in the lower 48 states. I will ship internationally for the added cost.

Email me at procketrichard@hotmail.com for more pictures or any questions.

I have a nice used Milodon gear drive part # 13600 for small bock engines. This was used on my W2 headed 360 bracket motor. It provided rock solid ignition and cam timing. I was saving this for a future rebuild however I sold the car so this is no longer needed. All the gears and bearings are in great shape. Pictures do not show the mounting bolts but they will be included.

Description from Summit Racing is as follows:

“Milodon timing-gear drive assemblies are designed for all-out competition, but work equally well in any application. Their proven fixed idler gear system is capable of maintaining consistent cam timing without siphoning off power the way 4-gear types can. Timing changes are easy via Milodon's adjustable bolt pattern cam gears and hub assemblies. Made for strength and durability, these gear drives will last indefinitely. They are available in a flat-cover style, which uses a stock-type water pump, or an injected/blown style, which doesn't use a stock-type pump.”

Price is $325 shipped in the lower 48 states. I will ship internationally for the added cost if any.

Email me at procketrichard@hotmail.com for more pictures or any questions.

I have a new Holley 750 vacuum secondaries Part # 0-3310S for sale. It has been sitting boxed on the shelf for a couple years. I am not going to use this so I am offering it up for sale. Below is the description from Holley.

“The 0-3310S is a shiny aluminum version of the classic 0-3310 - a hot rod staple for over four decades! Dual feed fuel inlets assure you get all the fuel you need while its vacuum secondaries and manual choke make it amazingly universal. The famed 0-3310 is one of ten inaugrual inductees into the Hot Rod Magazine Speed Parts Hall of Fame! Its well known performance calibration and 750 CFM airflow keep it on top still today. Don't trust your performance to just anyone, Holley is the only modular carburetor company that has been in business for over 100 years and has powered every NASCAR champion since the 60's.

Features:
- Vibratory polished for good looks
- Performance upgrade for stock to mildly modified vehicles
- Universal calibration for easy bolt-on performance
- Manual choke (cable actuated - hand controlled) for precise cold start control
- Vacuum secondaries for use on wide variety of vehicles. Compensate for all vehicle weights, gearing & transmissions to allow smooth opening of secondaries.
- Dual feed fuel inlets for constant high volume fuel delivery
- Compatible with GM, Chrysler, and Ford A/T kickdown linkage. Additional parts may be required.
- Power valve blow-out protection
- 100% wet-flow tested by Holley technicians to assure it arrives ready to run!”

Price is $390 shipped in the lower 48 states. I will ship to other destinations for any additional cost.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

I have a new MSD Digital 6AL ignition module part #6425 with built in rev limiter. It comes with all the original hardware still in the package and the harness.

Here is the description from Summit Racing.

“Advance with the digital power of your popular favorite--MSD 6AL ignitions. With less power draw and higher output, MSD moves you with "the fire to drive" in a digital powerhouse! Inside microprocessors, updated circuits and efficient components monitor and handle every firing and rev limit to produce more power while pulling less current. Don't worry; features that made their 6AL boxes your first choice remain but with improved output--more than135mJ of spark energy for every firing with 530+ volts to the coil! And, to go with the new power, a new look. These digital 6AL ignition controllers are sleek with a lower profile. Wiring is routed out one end through a sealed and locked connector and two rotary dials to set rpm limit are positioned right on top--easier installation, super easy access and a clean, neat appearance under the hood. Controllers are supplied with wiring harness and components you need for install plus, vibration mounts. Increased output and proven multiple-spark power--MSD digital 6AL ignition controllers are a definite win-win!.”

Price is $275 shipped in the lower 48 states. I will ship internationally for the added cost if any.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

I have a new MSD 7AL2 ignition module part #7220 and a used MSD Pro Power coil that is designed for use with the 7 series ignition boxes. The ignition box comes with all the original hardware still in the package and the harness. The coil was tested and has tested fine.

Price for the ignition box and coil is $650 shipped in the lower 48 states. I will ship internationally for the added cost if any.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

I have a very nice Demon 750 CFM carburetor featuring mechanical secondaries, 4 corner idle screws, 4150 mounting flange, no choke horn or choke and a small air hole drilled in each base plate butterfly. This carb worked great. It was used for testing a few engines on an engine stand and is no longer needed. It was cleaned, drained of gas and packed away.

Carb looks to be complete. All linkage moved freely with no binding. Throttle blades all move freely and open completely.

Price is $460 shipped in the lower 48 states. I will ship internationally for the additional shipping cost.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

1250 Holley Gen 3 Ultra Dominator Carburetor for sale....$900 + Shipping

So I have a newer 1250 carb, and it started life as a 3- circuit carb, and I had it converted to 2-circuit carb by Thumper carbs. It has not been used in a year and just sits in the box. Its the shiney polished silver and black. Was run on my 605 Hemi...and ran well. I can post actual pictures as soon as the camera is charged. I have double that price into it, and the old metering blocks come with it.

#TC-39, and he keeps good records. I have made a few minor changes and probably have all of them written down somewhere.

FAST XFI 2.0 ECU, Part # 301000 for sale.
Used FAST XFI 2.0 self-tuning EFI system with harness in great condition. All electrical harnesses are included to get your engine running. Also includes a new power adder harness, which is used for Nitrous control or Boost control and an adapter cable for the distributor to allow you to connect to a Holly/MSD dual sync distributor if you’re not using a FAST dual sync distributor. Includes the FAST/ NTK wide band O2 sensor, 1 BAR MAP or 2 BAR MAP sensor and C-Com laptop cable. The only sensors that you should need to get your engine running are the air and water temp sensors, which are inexpensive GM sensors, and the TPS and IAC, on your throttle body. NO throttle body is included. The only reason I’m selling this is because I needed to switch to a Holley Dominator ECU because I needed more inputs and outputs and drive-by-wire throttle control. Below is more info on the ECU.
FAST XFI 2.0 Engine Control Units
FAST XFI 2.0 engine control units deliver--fast! Utilizing the latest technology, FAST XFI 2.0 units can process, analyze, and adjust four times quicker than previous EFI systems. The C-Com XFI Windows-based software is easy to navigate and features field-flashable capabilities, so you can download the latest software updates via email or directly from FAST. These XFI control units also feature Qwik Tune for programming without a laptop. Pre-program up to four different EFI maps--optimize a setting for your daily driving, one for racing conditions, and still another for fuel economy. You'll enjoy on-board diagnostics, EZ Test indicator lights, 5-bar MAP sensing and controls, plus enhanced data-logging capabilities and memory.

Some of the FAST XFI 2.0 engine control units' standard features include:

* Built-in wideband O2
* Fully sequential and/or bank-to-bank capability
* Individual cylinder correction
* Fan and fuel pump control
* Dynamic scaling of vectors in 2D and 3D tables
* Torque converter lockup control
* Air conditioning wide-open throttle cutout
* Boost control
* Fuel and oil pressure logging
* Adjustable injector timing
* Multiple ignition strategies
Asking $500 + Shipping. PM me here for more info.

(New In Box - Still Sealed) AutoMeter Super-Lite Shift Light - Part# ATM-5332

Located in Arizona.

Retails for $123 at Summit or JEGS, etc.

https://www.summitracing.com/parts/...SxtfnigMVVSpECB3QVC8jEBwYAiABEgLwuPD_BwE

$90 shipped in the U.S. Accept PayPal, personal check or money order.

PM me if you want it. Thanks Moparts!

1 3/4" headers, unknown brand, were last on 67 b body low deck edelbrock rpm heads. Coated 10 yrs ago. Also have 3" H- pipe available for same car. Headers only $400 plus shipping. Call or text 630 six 74-3nine2seven

Mopar Performance 426 HEMI aluminum crossram intake manifold, it was bolted on a engine at one time but never ran $1650.00 (708) 288-2879

These are IMO an upgrade/redesign of the long offered well accepted STD Mopar rear axle steel tie downs.
Over a year ago I offered the vendor to pay any reasonable costs he incurred to build me a few sets of alternate material, like SS or Ti.
He declined. I suggested just build a few sets and see if there is a market for it. No deal. There is IMO nothing wrong with the steel tie down currently offered.

So, after a year of planting the seed, I just decided to just do it myself.
I was fortunate enough to acquire some suitable super alloy at a decent cost for the project, Inconel 718 or AMS 5596.
This gave me some additional leeway in the design. I have had many unique items copied in my niche business over many decades, it is a little annoying and few if any of the copies were better.
What I have here I believe is better, but I am not in business to produce them, I have limited amount of material able to be dedicated first to my cars
When the extra sets are gone, I'm likely done with the project.

Inconel's most widely known attribute is its strength in high temps, like turbo exhaust valves, which obviously does not apply here.
Its raw very high strength, high fatigue life and corrosion resistance are very useful qualities however in this application.
The steel version pictured is .250" thick and weighs 29oz, and steel is usually in the 60Ksi Tensile and 35Ksi yield range.
The break for bending, steel being a softer material, leaves a noticeable mark.
The Inconel here is .159" thick with an optimized design and weighs 13oz, I calculate it's about min 2x the strength of the steel offering. Any additional drilling if needed is likely a rather tough task.
Nickel Alloy 718 / Inconel 718 (UNS N07718)- Aircraft Materials There are many sources online for your own verification
++++++++++++++++++++++++++++++++tensile ksi___ yield ksi __ elongation __ Hardness
Alloy 718 Sheet AMS 5596 Aged < 0.1874" thick____ 180​ ______ 150 _______12_______ ≥36 HRC

Pair shipped USPS lower 48 $150, does not include nuts. First PAID, First served, these are not for everybody, but it might be hard to find a better solution. PM

They also may polish up real well, but I don't know as I haven't tried

For Sale Sanders Wheels 15 x 12 6 inch backspacing. 5 x 4.5 bolt pattern $700 in Stroudsburg Pa, selling for a friend Scott 1-570 -460-6090 or pm me or lbvracing@aol.com

******no longer available ******



Old but NEW unused stock hydraulic lifters for small block. Part #HT2011. All have a very consistent crown of .003 checked in my tool fixture.

14 vintage Keystone Klassic wheels, some are 14 inch, some are 15 inch, most are 4 1/2 inch bolt circle, a couple are 4 3/4 inch bolt circle, there are no unilug, selling as is, selling as cores to restore, what you see is what you get $2000.00 for everything (708) 288-2879

Pair of A Body Tubular Upper Control Arms. Heim Joints and Ball Joints are perfect and ready to install. I had brackets welded on to attach travel limiters. These arms were in my car for a very brief period of time due to a change in plans. $350. rich1981@optonline.net SOLD

Wilson Manifolds 4500 to 4150 low profile adapter.
$150

Wilson Manifolds 1.5 inch 4 hole tapered spacer for 4150 #004130
$150


ATI Super Damper #917467E BB Mopar. $225

Thanks Moparts

Buyer pays shipping

A pair of Weld Magnum 2.0,15" fronts. Good condition. One wheel has a slight wobble. $500 + shipping for the pair.

Mopar performance P4876548 high performance SB water pump.

Radiator connection tig welded to clear large fuel pump

$385 obo

thanks

rapid340@yahoo.com

Super nice Holley double pumper 4 bbl 4776 classic

These are around $750 (plus tax) new

$385

thanks

NOS Mopar Performance intake manifold

large port intake for use with W5 or similar heads.

$485

thanks

rapid340@yahoo.com

The mufflers are brand new and were out the boxes for fitting only.

$160 for the pair plus shipping or pick up.

Thanks

These Carbs came with the engine I had built, and they are basically brand new with only engine run in time. They come with Carb Kits from AED and Quick Fuel Adjustable Secondaries.

$1380 for the pair plus shipping. ****SOLD****

Thanks

Driveshaft Loop was new, bolted it up on car, decided to do something different.

$70 plus shipping. **SOLD**

Thanks

Wilwood Brake Proportioning Valve===as you see it , just the valve.

$25 plus USPS shipping from Syracuse NY

Pay Pal only. Shipping will be USPS Flat Rate or being a smaller item maybe just first class.

2 Book Racing Carbs,1250-1500 CFM .,,,,,,,2500 OBO,,,,,,,,,,,,,,,,,,C&R racing radiator 22X13 with extras,,,,,750.00,,,,,,,,,,,,,,Complete dry sump oil system,1250.00,,,,,,Coan racing trans,,turbo 400,..4500 stall,,,,make offer,,,,all parts have about 2 hrs run time on them,,,,,COMPLETE motor setup,disassembled is available,,heads have damage,,block,pistons,ect good shape....St Louis area.....,,message me for pictures

.940 A body Torsion Bars for sale. New, never used. Purchased from Firm Feel a few years ago. Shown on their site as H/D - Police usage. (WR155) TBA3 . Listed for $500. $350 negatable plus shipping in their original box. Possible delivery assistance in Lower Michigan area. Contact me thru Moparts.

I have a good pair of 572-13 heads, Jesel rockers kit and matching CFE 2x4150 sheet intake WITH linkage. Ti 2.3 coated intakes and Ti 1.88 exhaust. Set up made over 900HP on a 452 RB about 20 years ago. Need an exhaust valve job and springs. I can finish them to your liking for extra money. I was going to use these to make 1050HP with some tune-ups and bigger cam but have Predator heads now. These will push a 3200# car solid into the 8's as-is at a nice low rpm. (bracket) Chambers are about 66cc now and can be milled further. $3800. (Heads and Intake PENDING) I have two fresh and matched '950' HP carbs, tuned well on my last motor $1400 with package. 55mm 4/7 swap cam about .790' NET lift with heads $425 with package. New 572-13 CP 4.507" 1.2 C/H pistons with rings/ latest tricks $1800 with package. Good stuff! Heads were painted and I'll detail/clean them when purchased. Decks are good currently. Contact thru Moparts Thanks!

* 3" x 7/8" T-Bolt exhaust clamps from TTI kit made by Five Star MFG. 11 new, 1 used (Range approx. 3" - 3 1/4")
Bands are stainless, bolts are plated.

* 3' standard exhaust pipe clamps - 2 new

All for $55.00 including shipping within the 48 states from Florida 32117.

Sorry, no PayPal.

locomo@bellsouth.net

Lead Shot bags & loose - Race car ballast, fishing, scuba, etc.....

* Lead shot nylon bags - 2lb - 5lb range - 61lbs+ total

(Contrary to the tags, a few are off by as much as a pound, but total is 61lbs+)

$225.00 including Priority Flat Rate shipping within the 48 states from Florida 32117

(Would prefer to ship to a business address which may make it easier to deliver and accept at that weight.)



* Lead shot - loose in bag 23lbs+ total

$45.00 including Priority Flat Rate shipping within the 48 states.from Florida 32117


Sorry, No PayPal.

locomo@bellsouth.net

65 up b body milodon pan. Outer finish is pretty much wore off, inside is good. I never used it. But appears to not be any damage that would prevent good use. No pickup included. 9.375" deep inside. $300 plus shipping. Can send more pictures, it says my others are to big

SOLD SOLD:::::;::::Good rockers I used in the past and have been on the shelf. Some adjusters are different lengths where some got changed, could use some new locking nuts. Definitely usable if wanted to. $200 plus shipping SOLD SOLD

TCI Super Street Fighter big block Mopar transmission upgraded with CRT reverse manual valve body. Works perfect. TCI rates this unit up to 750 hp.
Pick up only in Warren Mi. NO SHIPPING

$1999
PM or John 586-222-2728 jonburdine@yahoo.com

Edelbrock #2920 Victor W2 Rectangular port intake manifold in good condition.

$250 + ship. *******SOLD*******

PM or GTX5877@yahoo.com

ARP Pro Series Cylinder Head Studs #144-4202 for SB Mopar with W-2 cylinder heads. 12 point nuts, washers and 8740 studs. Over $200 new. Sell for $100 + shipping from 56007

Private message

This is a pair of bare NOS stage IV heads for BB mopar still in the factory boxes. The casting numbers are 3614470. Honestly I would prefer a cash and carry type of deal, and not to ship them unless I have to.
I will be attending the Indy Cylinder head swap meet at the end of the month and I could deliver them to the show with a deposit. Asking $1000.00 OBO for the pair. My Email is otissteph@yahoo.com if you are interested. I was not able to to post pictures, but I can take pictures as needed. located in Cookeville, TN
Thank you, Matt

Like the title says, Direct Connection 4782 4783 Holley mechanical six pack carb set. All three carbs need rebuilt as they have been setting for many years. I have an extra fuel bowl and few parts that will go with them. $1200.00 obo for the set of 3.
Can deliver to Indy Swap meet.
Pm me here.
Matt

Transbrake valve body, serviced with new filter and extension, deep pan w/bung for gauge. Works as it should, was in my car. $400 obo plus shipping

IPredator 4500 Single Four Manifold
Retail Price: $1,580.00

Predator Manifold 4500 Single Four, Horsepower Big Volume

Manifold has cast in fuel injection bungs and fuel rail mounts. All fuel injection components can be installed by ICH or purchased separately from Indy Cylinder Head.

The Predator combination is unchallenged in the world of performance as a cylinder head and air/fuel induction system.

This is un-ported, no milling, as new $1150 Shipped lower 48 states

Text or call John 586-222-2728 or pm