I have a few sets of new ductile iron main caps available for 360/5.9 magnum engines. These are Mopar Performance caps. I have sets for both 360. The sets includes the first 4 caps. The center 3 caps are 4 bolt main. These are the same caps that came standard on R3 4 bolt blocks. I have installed these caps on a 340 before by milling off the ends of the center caps to leave them 2 bolt. See pictures for the 3 modified center caps installed on a 340 stroker engine. These caps are more stout than the stock caps and are an excellent upgrade for any high performance build. A line bore will be needed when installing new caps as well as some machining for the thrust bearing on the #3 cap.

Price is $340 shipped per set in the lower 48 states. I will ship internationally for the additional cost.

Email procketrichard@hotmail.com for more information.

I have a new set of 8 Mopar Performance pistons and wrist pins Mopar part# P4876973 for a 3.454” stroke crankshaft. Specs are 4.060” bore, 1/16, 1/16, 3/16 ring set, 0.984” wrist pin, flat top with ~ 5 cc eyebrows, listed by Mopar as 10.5 compression ratio. Compression height is ~ 1.72” per my measurement.

Price for the set is $480 shipped in the lower 48 states. I will ship internationally for the extra cost.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

I have a set of New BRC 4.030" forged flat top pistons and pins for a 3.79" stroke small block crankshaft. Compression height is ~ 1.57" and the ring lands are 1/16, 1/16 and 3/16. Pins are 0.984”. Approximately 6cc valve reliefs.

These pistons can be used in aftermarket race blocks or stock 360/5.9 magnum engine blocks with 4.030” finished bores.

Price is $475 shipped in the lower 48 states. I will ship elsewhere for the added cost.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

Chevy water pump to big block Mopar adapter. Don’t remember brand. $125 plus shipping from 70072 PayPal or postal money order

Afco Eliminator Front Shocks Single Adjustable . Used 1 season before upgrading to double adjustable. $300 plus shipping from 70072. Postal money order or PayPal friends and family

New, in-the-box RM-6073 QuickTime bellhousing for Chrysler big block, using 130T flywheel. All parts included as from the factory, $950 shipped within the continental 48 states. PM me here if interested, thanks.

For Sale Willy’s adjustable plate throttle stop for 4150 carb , great for index racing $433 now from
Summit asking $300 new price ! $250 price negotiable shipping extra lbvracing@aol.com or pm

Rear trailer tie down brackets for most A, B, or E body vehicles (doesn’t fit the 7 ¼ rear axle). These piggyback onto the bottom of the stock shock plate mounting nuts and then 4 more nuts hold these tie down brackets on. You must have enough extra thread hanging down on the bottom of your U-bolts to fit the ¼” thick tie down bracket and another nut. No disassembly necessary, just slide the brackets over the extra thread on your U-bolts, install the included nuts, tighten them down and you’re done. Takes about 10 minutes to install. These eliminate all the hassles that come with using axle straps. Fits A, B, and E body cars with the standard shock plates like shown in the pictures. $60.00 per pair plus shipping. I also have these available for cars with CalTracs, same price. Made in the USA.
Email mrrandyj@aol.com

Reactor Products New Old Stock from 2/94. 8 bolt crank to powerglide aluminum flywheel . $100 plus shipping from 70072. Postal money order , PayPal friends and family or add fees

NOS Mopar performance 1.6 ratio SB roller rocker arms

1.6 ratio often very effective when used on intake valves.

Made in USA

$315 plus shipping for EIGHT(8) individual rocker arms.

thanks

rapid340@yahoo.com

NOS Mopar Performance intake manifold

I believe this is a large port intake for use with W5 or similar heads. A little dirty but never used,

$585 prefer pickup (NE Ohio)

thanks

rapid340@yahoo.com

short deck cover 275 short deck distributor 375
Buyer pays actual shipping. Will show receipt for shipping cost.

Open to reasonable offers

Up for sale is a new in box msd gen 3 hemi controller and engine harness so you can run a carb. $700
-440 Edelbrock efi proflo 4 kit. Used 250 miles. Ran excellent. Took off for boosted application. $1600
Zip is 80550.
Please send PM if interested, thank you

sold thanks

596
Indy block
B1 heads done by BES
Indy R3 cam
Bam lifters
Manley vavle springs
New T&D paired rockers 1.7 ratio
Callies 4.625 crank
Callies ultra rods
Ross pistons
Trend 7/16 .165 pushrods
Koffels RB B1 intake (1 of 7 Made)
C&S 1400 billet aerosol carb
Indy offset dist
Firecore wires
Olson oil pan
Moroso 3 vane vacuum pump
Went 4.64 @146 in dragster all motor
Has been 6.72 @ 199 on Spray
Motor has 45 runs on it since freshening
Any questions please call
Scott Foster
937-538-8027
20,000 firm
Motor in the picture of car attached

Mopar Performance 426 HEMI aluminum crossram intake manifold, it was bolted on a engine at one time but never ran $1650.00 (708) 288-2879

Sold

JW BBM to powerglide bellhousing no Sfi sticker. Part#92456 $300 plus shipping PayPal plus fee or postal money order

Mopar RB tach drive race distributor. $200 plus shipping. PayPall plus fee or postal money order

Sold