For sale is a "NEW" in the box Holley HP Billet adjustable fuel pressure regulator. Part number 12-846. EFI applications. Bypass style. Adjustable from 15-65 PSI. -8AN o-ring inlet. -8 o-ring outlet. -6AN o-ring return. $160 shipped in the 48 states. PM if interested.

https://www.jegs.com/i/Holley/510/12-846/10002/-1

Wanted 408 engine or bigger with Single 4 intake.

Mark 724-433-0527

70 B-body voltage regulator mounting bracket. $15

New chrome coil cover & coil mounting bracket. $20

NOS Cal Custom chrome radiator cap. $20

NOS Cal Custom chrome battery hold down. $25

Four new extra wide chrome valve cover hold down clamps. $10 for the set

New exhaust manifold heat stove to air cleaner flexible hose. $20

NOS fan clutch 3769614 for 1974 all V-8 engines. $100

Factory warning light type oil pressure sending unit. $10

Gauge type oil pressure sending unit. $20

Vintage Cal Custom 14" finned aluminum air cleaner with filter. $100

New 12" oval 4 barrel finned aluminum air cleaner with filter. It measures 12" L x 8 1/4" W x 3" H and has a 5 1/8" carb opening. $55

New Mopar Performance chrome water neck. Was bolted on an engine but then taken back off before the engine was ran. $10

AC alternator bracket from a mid 70s 360. $10

New Mr. Gasket chrome oil filter cover. $15

9 Chrome t-handle valve cover bolts. $10

Factory starter, part/casting #3755259. This came off of my Dart about 10 years ago. Worked fine then, been sitting on a shelf ever since. $40

Two 318 driver side spool motor mounts pt#3642811. One is used and one is NOS. $20 for the used. $35 for the NOS.

Edelbrock Elite small block valve covers EDL-4295 with bolts, breather & PCV valve. Very nice condition. $200

NOS Cal Custom chrome dagger dipstick handle. $25

New Mopar Performance 5 blade radiator fan and clutch. $100

Pioneer Automotive cylinder head dowel pins. 21 pieces 1/4" x 5/8". $10

Howard's solid flat tappet cam for Mopar big blocks, part number CL722322-08. See links below for specifications. I bought this cam for my engine with the intention of taking the car to the track when the car was finished being restored along with the engine being built but I have changed my mind about racing the car and decided to go with a milder hydraulic cam instead. I had this cam installed in my engine on the engine stand only (engine is still on the stand) so it has never been run and is essentially new. $375

New set of COMP Cams 973-16 - Inner Valve Springs. $45

Chrome single groove alternator pulley. $15

1975 Date coded alternator. Part #3874271. $25

Rev-n-nator Coil and programmable ICU. $200

Vintage Cal Custom scoop style air cleaner. Includes often missing matching wingnut. $300

New in boxes QTP 2 1/2" electric exhaust cutouts #QTEC50, stainless y-pipes #10250 and remote controller #10900. $654 total price at Summit. $550

Prices do not include shipping. No Paypal

Email: gt340 @ yahoo.com

llooking for a new camshaft part number 2899205 , which is the 1968 340 manual transmission camshaft. Im out in california...dm me here...
Thanks for the ad.

Looking for '70 340 driver side valve cover that would be correct for a TA 340. Also wanting a 70 date coded small block alternator. PM me with what you have. TIA

New 360 & 5.9 Magnum Assembly-408”

I have a new SCAT forged rotating assembly for 360 & 5.9 Magnum Mopar engines. All parts are new high-quality parts. Final cubic inches will be 408”.
The assembly includes the following parts.

• SCAT forged 4.000” crankshaft part # 4-360-4000-6123
• SCAT forged H-beam connecting rods with APR 2000 bolts part # 2-360-6123-2124A
• Diamond Forged flattop 4.030” bore pistons (0.030” oversize) part # 51026
• Trend wrist pins - 0.984” part # TPD-G9842750155
• Diamond wrist pin locks
• Mahle file fit ring set with Moly ductile iron top rings part # MAH4035MS
• Speed Pro Tri metal Competition Series rod bearings part # 8-7125CH
• Clevite P-Series full groove main bearings part # MS-1266P

If you are looking for a 360 stroker with lower compression, I can substitute the pistons and connecting rods for new SRP 4.030” dished pistons part # 220156 (16.9 cc piston head volume) and new Eagle H-beam rods part # CRS6123C3D (360 stroker assembly only).

These rotating assemblies will need balancing.

The price for this complete kit with the Diamond flat top pistons and SCAT rods is $2,750 plus shipping cost.

The price for this complete kit with the SRP dished pistons and the Eagle H-beam rods is $2,600 plus shipping cost.

I also have a similar stroker assembly for a 340 with new Diamond 4.060” (0.020” overbore) flat top pistons, Perfect Circle file fit ring set with Moly ductile iron top rings part # 315-0036.065
and Speed Pro Tri metal Competition Series rod bearings part # 8-7125CH. Displacement would be 414 ci. This rotating assembly will need balancing.

The price for the complete 340 kit is $2,750 plus shipping cost.

I can also meet in CT.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

I have a new forged rotating assembly for 340 Mopar engines. All parts are new high-quality parts. Final cubic inches will be 414”.
The assembly includes the following parts.

• SCAT forged 4.000” crankshaft part # 4-340-4000-6123
• SCAT forged H-beam connecting rods with APR 2000 bolts part # 2-360-6123-2124A
• Diamond Forged flattop 4.060” bore pistons (0.020” oversize) part # 51028
• Trend wrist pins part # TPD-G9842750155
• Diamond wrist pin locks
• Perfect Circle file fit ring set with Moly ductile iron top rings part # 315-0036.065
• Speed Pro Tri metal Competition Series rod bearings part # 8-7125CH
• Clevite P-Series full groove main bearings part # MS-1344P

This rotating assembly will need balancing.

Price for this complete kit is $2,750 plus shipping cost.

I can also meet in CT.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

I have 11 pairs (one complete engine set plus 3 spare pairs) of new Mopar Performance solid roller lifters for small block still in their packages. I took one pair to photograph. Part number is P5249584. See the included picture from the 1997 Mopar Performance catalogue for the description. The roller wheel size is ~ 0.80”.

I fit these into my stock 340 block and they fit in nicely. On my block, the block required very minor grinding to a very small spot in the raised section of the valley to allow two of the eight lifter pairs to slide in. Contact was in the center of the link bar.

The price for the 11 pairs is $650 shipped in the lower 48 States. I will ship internationally for the additional cost.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

I have a new PRW 1.6 ratio roller rocker arm kit containing all parts needed to install these rocker arms including steel bushed rocker arms, rocker arm shafts, spacers, shims, adjusters, steel shaft hold downs and hold down hardware. This kit is new in the box and is PRW part # 3231812.

Price is $500 shipped in the lower 48 states.

I will ship internationally for the additional shipping cost.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

I have a set of New BRC 4.030" forged flat top pistons and pins for a 3.79" stroke small block crankshaft. Compression height is ~ 1.57" and the ring lands are 1/16, 1/16 and 3/16. Pins are 0.984”. Approximately 6cc valve reliefs.

These pistons can be used in aftermarket race blocks or stock 360/5.9 magnum engine blocks with 4.030” finished bores.

Price is $475 shipped in the lower 48 states. I will ship elsewhere for the added cost.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

I have a new set of 8 Mopar Performance pistons and wrist pins Mopar part# P4876973 for a 3.454” stroke crankshaft. Specs are 4.060” bore, 1/16, 1/16, 3/16 ring set, 0.984” wrist pin, flat top with ~ 5 cc eyebrows, listed by Mopar as 10.5 compression ratio. Compression height is ~ 1.72” per my measurement.

Price for the set is $480 shipped in the lower 48 states. I will ship internationally for the extra cost.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

I have a 440 six pack center carb part # 4144-1 that was factory reconditioned by Holley. Has not been run since reconditioned. Can also be used on 340 six pack engines but may require a jet change.

$750 shipped in the lower 48 states. I will ship internationally for the added cost.

Email me at procketrichard@hotmail.com for more pictures or any questions.

small block polished RPM intake 350+ actual shipping will show receipt located in southern California San Fernando Valley brand new never ported never installed

SOLD

Custom Small Block 3,4 Speed Throttle Cable Bracket. Used, $25 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097

Note: Works with any high rise intake or carburetor spacer

W-2 Small Block Throttle Cable Bracket. New, $15 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097

Small Block Carburetor Throttle Return Spring Brackets. Used, $15 each + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097

Factory Small Block Valve Covers 318,340,360, Used, $50 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097

Note: All Harness, Wire Brackets Intact!

Factory Small Block Valve Cover Breather. Used, $15 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097

Valve Cover Oil Fill Caps. Used, $10 Each + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!

1. Not sure!
2. 73-74 model (came of my 73 Cuda)
3. Mopar Preformance Chrome New!
Call Steve 810-629-1097
Note: Pick the one you want by photo 1-3

Small Block Spark Plug Wire Looms. Used, All 7 Looms, $25 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097

Small Block Heater Hose Bracket. Used, $15 + Shipping. Payment via US Postal Money Order. Shipping: US Address Only!
Call Steve 810-629-1097

Small Block Distributor Hold Down Bracket. Used, $15 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097

P4120484 Fuel Pump Eccentric Small Block 273, 318, 340, 360. Used, $20 + Shipping, Payment via US Postal Money Order Only!. Shipping: US Address Only!
Call Steve 810-629-1097

Casler Small Block Headers 273, 318, 340, 360. Used, $150 + Shipping. Payment via US Postal Money Order Only!. Shipping: US Address Only!
Call Steve 810-629-1097

Water Pump To Fan Spacer 1.25 in' Thick. Used $15 + Shipping. Payment via US Postal Money Order Only!. Shipping: US Address Only!
Call Steve 810-629-1097

63-76 Temperature Sending Switch #2426458 Used $7.50 + Shipping
62-80 Oil Pressure Sending Unit For Models With Warning Light. Used, $7.50 + Shipping.
Payment via US Postal Money Order Only!. Shipping: US Address Only!
Call Steve 810-629-1097

Fram CA160 Air Filter. New, $5 + Shipping. Payment via US Postal Money Order Only!. Shipping: US Address Only!
Call Steve 810-629-1097

Note: Used On Any 2bl Motor, See Photo 2 For Application!

Factory Carburetor 3.5 in" Stud With Wing Nut. Used, $10 + Shipping. Payment via US Postal Money Order. Shipping: US Address Only!
Call Steve 810-629-1097

73-74 Electric Choke #3656730 All Models, Used, $35 + Shipping. Payment via US Postal Money Order. Shipping: US Address Only!
Call Steve 810-629-1097

Holley 4749-2 Carburetor Factory 383-440. Used, $125 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097
Note: Came Off A 70 RT/SE 383 Challenger

Gates Single Belts.New, $10 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!

1.Gates Belt 7470
2. Gates Belt 7490
3. Gates Belt 7580

Call Steve 810-629-1097
Note: Pick the one you want by photo 1-

Gates / Mopar Duel Alternator / Fan Belts.New, Price Below + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!

1.Gates Duel Belt #7541 $20
2. Mopar Duel Belt #4106241 $25

Call Steve 810-629-1097
Note: Pick the one you want by photo 1-2

68-69 440 Unsilenced Air Cleaner With K&N Filter. Used, $275 + Shipping. Payment via US Postal Money Order. Shipping: US Address Only!
Call Steve 810-629-1097

Wanted - small block Mopar purple shaft 284/484 hydraulic camshaft kit, PN P4120231

For sale: 340 sixpack set-up, Edelbrock intake, 440 sixpack carburetors, aircleaner. $3500. Located in Palmdale, CA. Email: ebodycab@msn.com. Phone: 818-426-8685.
Pictures available upon request. SOLD.

Single Groove Water Pump Pulley that I'm looking for:

6" - 6 1/2" OD, 2 1/8" - 2 1/4" depth measuring from the back edge of the pulley to the inside face of the pulley (where it mounts to the water pump).

PM me here

Thanks Moparts

For sale is a set of rare original Mopar T/A 340 six-pack cylinder heads,correct rockers with the intake offset and pushrods. Factory for the Dodge T/A Challenger and Plymouth AAR 'Cuda. These are in good shape but shouild be considered cores for refurbishing. Rockers all move on shafts but some have limited travel and only rotate a small amount. Located in Pittsburgh PA, 15229.
$3500.oo

Set of 340 TA Heads
No Rockers or shafts.

Heads were cleaned and magnifluxed.
See pictures and contact me with any further questions.
Heads were modified to add steel O-rings (a High-Perf mod from 'back-in-the-day).
Some light porting on intake and exhaust- no break-through or welds.
The only issue the Mag-ing identified was slight micro-cracks on the inside of the combustion side of the spark-plug threads (this is common from over-torquing spark plugs)
Bronze guides in place.
$2000
Would prefer not to ship.
Located in SE Wisconsin

CSR water pump for small block. Used one season. $200 rich1981@optonline.net

I have a set of 340 T/A heads with valves,springs,correct offset rockers,shafts and pushrods. Some rockers are stuck,sitting for 20+ years(inside) and pulled from the engine a few years ago.Good shape overall but shouild be considered as rebuilder cores.No porting done to the heads. I'll add pics soon. Edit: Most rockers spin freely on shafts,some have limited travel for some reason but are not galled on the shaft.
Located in Pittsburgh,PA 15229
Asking $3500.00 for all
PM here,E mail to RTSrunner-at-yahoo dot com,text to 412.4oo.o974; Thanks RT

Barracuda Cuda Challenger

No pins, new, CH approx 1.56"
8 .030 over, small dish as pictured
$60 OBO plus shipping, PM

Never run/mounted, almost new #P5007065, as pictured
One port was deburred, port cleaned up, and valve job, reported to flow 350cfm
Heads were pressure tested, tech states there is lot more left in the heads flow wise.
$1600 pair, plus shipping, PM, delivery east of Mississippi possible for extra fee

I'm looking for a late 1968/early 1969 340. Block, short block, complete, core or rebuilt. Just need one for my GTS.
Located in central Ohio.

Nos Perfect Circle 340 cam #229-1654. Lift is verified by me. Made when cores and grinding were good. Will pack well. $175 shipped lower 48. Postal money order. Pm me here

Small block distributor, used, #3690430. $80 plus shipping.

Steve - magnumracing@sbcglobal.net

I'm looking for a single Poly 318 valve cover to cut up for use as a tool to view oil transfer on a running engine. Condition doesn't need to be perfect.

Please PM me here if you have anything. I'm located in NW Oregon.