70 B-body voltage regulator mounting bracket. $15

New chrome coil cover & coil mounting bracket. $20

NOS Cal Custom chrome radiator cap. $20

NOS Cal Custom chrome battery hold down. $25

Four new extra wide chrome valve cover hold down clamps. $10 for the set

New exhaust manifold heat stove to air cleaner flexible hose. $20

NOS fan clutch 3769614 for 1974 all V-8 engines. $100

Factory warning light type oil pressure sending unit. $10

Gauge type oil pressure sending unit. $20

Vintage Cal Custom 14" finned aluminum air cleaner with filter. $100

New 12" oval 4 barrel finned aluminum air cleaner with filter. It measures 12" L x 8 1/4" W x 3" H and has a 5 1/8" carb opening. $55

New Mopar Performance chrome water neck. Was bolted on an engine but then taken back off before the engine was ran. $10

AC alternator bracket from a mid 70s 360. $10

New Mr. Gasket chrome oil filter cover. $15

9 Chrome t-handle valve cover bolts. $10

Factory starter, part/casting #3755259. This came off of my Dart about 10 years ago. Worked fine then, been sitting on a shelf ever since. $40

Two 318 driver side spool motor mounts pt#3642811. One is used and one is NOS. $20 for the used. $35 for the NOS.

Edelbrock Elite small block valve covers EDL-4295 with bolts, breather & PCV valve. Very nice condition. $200

NOS Cal Custom chrome dagger dipstick handle. $25

New Mopar Performance 5 blade radiator fan and clutch. $100

Pioneer Automotive cylinder head dowel pins. 21 pieces 1/4" x 5/8". $10

Howard's solid flat tappet cam for Mopar big blocks, part number CL722322-08. See links below for specifications. I bought this cam for my engine with the intention of taking the car to the track when the car was finished being restored along with the engine being built but I have changed my mind about racing the car and decided to go with a milder hydraulic cam instead. I had this cam installed in my engine on the engine stand only (engine is still on the stand) so it has never been run and is essentially new. $375

New set of COMP Cams 973-16 - Inner Valve Springs. $45

Chrome single groove alternator pulley. $15

1975 Date coded alternator. Part #3874271. $25

Rev-n-nator Coil and programmable ICU. $200

Vintage Cal Custom scoop style air cleaner. Includes often missing matching wingnut. $300

New in boxes QTP 2 1/2" electric exhaust cutouts #QTEC50, stainless y-pipes #10250 and remote controller #10900. $654 total price at Summit. $550

Prices do not include shipping. No Paypal

Email: gt340 @ yahoo.com

I have a new SCAT & Diamond forged rotating assembly for 360 & 5.9 Magnum Mopar engines. All parts are new high-quality parts. Final cubic inches will be 408”.
The assembly includes the following parts.

• SCAT forged 4.000” crankshaft part # 4-360-4000-6123
• SCAT forged H-beam connecting rods with APR 2000 bolts part # 2-360-6123-2124A
• Diamond Forged flattop 4.030” bore pistons (0.030” oversize) part # 51026
• Trend wrist pins - 0.984” part # TPD-G9842750155
• Diamond wrist pin locks
• Mahle file fit ring set with Moly ductile iron top rings part # MAH4035MS
• Speed Pro Tri metal Competition Series rod bearings part # 8-7125CH
• Clevite P-Series full groove main bearings part # MS-1266P

This rotating assembly will need balancing.

Price for this complete kit is $2,750 plus shipping cost. I may be able to deliver to Carlisle or can meet in CT.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

I have a new SCAT forged rotating assembly for 340 Mopar engines. All parts are new high-quality parts. Final cubic inches will be 414”.
The assembly includes the following parts.

• SCAT forged 4.000” crankshaft part # 4-340-4000-6123
• SCAT forged H-beam connecting rods with APR 2000 bolts part # 2-360-6123-2124A
• Diamond Forged flattop 4.060” bore pistons (0.020” oversize) part # 51028
• Trend wrist pins part # TPD-G9842750155
• Diamond wrist pin locks
• Perfect Circle file fit ring set with Moly ductile iron top rings part # 315-0036.065
• Speed Pro Tri metal Competition Series rod bearings part # 8-7125CH
• Clevite P-Series full groove main bearings part # MS-1344P

This rotating assembly will need balancing.

Price for this complete kit is $2,750 plus shipping cost. I may be able to deliver to Carlisle or can meet in CT.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

I have a set of New BRC 4.030" forged flat top pistons and pins for a 3.79" stroke small block crankshaft. Compression height is ~ 1.57" and the ring lands are 1/16, 1/16 and 3/16. Pins are 0.984”. Approximately 6cc valve reliefs.

These pistons can be used in aftermarket race blocks or stock 360/5.9 magnum engine blocks.

Price is $475 shipped in the lower 48 states. I will ship elsewhere for the added cost.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

I have a new set of 8 Mopar Performance pistons and wrist pins Mopar part# P4876973 for a 3.454” stroke crankshaft. Specs are 4.060” bore, 1/16, 1/16, 3/16 ring set, 0.984” wrist pin, flat top with ~ 5 cc eyebrows, listed by Mopar as 10.5 compression ratio. Compression height is ~ 1.72” per my measurement.

Price for the set is $480 shipped in the lower 48 states. I will ship internationally for the extra cost.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

I have 11 pairs (one complete engine set plus 3 spare pairs) of new Mopar Performance solid roller lifters for small block Mopar race blocks still in their packages. I took one pair to photograph. Part number is P5249584. See the included picture from the 1997 Mopar Performance catalogue for the description. The roller wheel size is ~ 0.80”.
The price for the 11 pairs is $650 shipped in the lower 48 States. I will ship internationally for the additional cost.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

I have a pair of new individual W2 race head casting number P5249769. These heads have no machining performed. As delivered by Mopar including 3/8” iron valve guides and closed chambers. These heads require the use of T&D or Jesel rocker systems.

Price is $1,200 for the set plus shipping.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

I have a new PRW 1.6 ratio roller rocker arm kit containing all parts needed to install these rocker arms including steel bushed rocker arms, rocker arm shafts, spacers, shims, adjusters, steel shaft hold downs and hold down hardware. This kit is new in the box and is PRW part # 3231812.

Price is $510 shipped in the lower 48 states.

Email me at procketrichard@hotmail.com with any questions or for more pictures

I also have 16 new Mopar Performance 1.5 ratio roller W2 exhaust rocker arms for the W2 & W5 Race heads using offset drilled blocks and shafts. I will sell individual rockers or sets of 2, 4,6 or 8 as needed. Individual rockers are $40 each plus shipping. A set of 8 is $280 shipped.

Email me at procketrichard@hotmail.com with any questions or for more pictures.

Custom Small Block 3,4 Speed Throttle Cable Bracket. Used, $25 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097

Note: Works with any high rise intake or carburetor spacer

W-2 Small Block Throttle Cable Bracket. New, $15 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097

Small Block Carburetor Throttle Return Spring Brackets. Used, $15 each + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097

Factory Small Block Valve Covers 318,340,360, Used, $50 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097

Note: All Harness, Wire Brackets Intact!

Factory Small Block Valve Cover Breather. Used, $15 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097

Valve Cover Oil Fill Caps. Used, $10 Each + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!

1. Not sure!
2. 73-74 model (came of my 73 Cuda)
3. Mopar Preformance Chrome New!
Call Steve 810-629-1097
Note: Pick the one you want by photo 1-3

Small Block Spark Plug Wire Looms. Used, All 7 Looms, $25 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097

Small Block Heater Hose Bracket. Used, $15 + Shipping. Payment via US Postal Money Order. Shipping: US Address Only!
Call Steve 810-629-1097

Small Block Distributor Hold Down Bracket. Used, $15 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097

P4120484 Fuel Pump Eccentric Small Block 273, 318, 340, 360. Used, $20 + Shipping, Payment via US Postal Money Order Only!. Shipping: US Address Only!
Call Steve 810-629-1097

Casler Small Block Headers 273, 318, 340, 360. Used, $150 + Shipping. Payment via US Postal Money Order Only!. Shipping: US Address Only!
Call Steve 810-629-1097

Water Pump To Fan Spacer 1.25 in' Thick. Used $15 + Shipping. Payment via US Postal Money Order Only!. Shipping: US Address Only!
Call Steve 810-629-1097

63-76 Temperature Sending Switch #2426458 Used $7.50 + Shipping
62-80 Oil Pressure Sending Unit For Models With Warning Light. Used, $7.50 + Shipping.
Payment via US Postal Money Order Only!. Shipping: US Address Only!
Call Steve 810-629-1097

Fram CA160 Air Filter. New, $5 + Shipping. Payment via US Postal Money Order Only!. Shipping: US Address Only!
Call Steve 810-629-1097

Note: Used On Any 2bl Motor, See Photo 2 For Application!

Factory Carburetor 3.5 in" Stud With Wing Nut. Used, $10 + Shipping. Payment via US Postal Money Order. Shipping: US Address Only!
Call Steve 810-629-1097

73-74 Electric Choke #3656730 All Models, Used, $35 + Shipping. Payment via US Postal Money Order. Shipping: US Address Only!
Call Steve 810-629-1097

Holley 4749-2 Carburetor Factory 383-440. Used, $125 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!
Call Steve 810-629-1097
Note: Came Off A 70 RT/SE 383 Challenger

Gates Single Belts.New, $10 + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!

1.Gates Belt 7470
2. Gates Belt 7490
3. Gates Belt 7580

Call Steve 810-629-1097
Note: Pick the one you want by photo 1-3

Gates / Mopar Duel Alternator / Fan Belts.New, Price Below + Shipping. Payment via US Postal Money Order Only! Shipping: US Address Only!

1.Gates Duel Belt #7541 $20
2. Mopar Duel Belt #4106241 $25

Call Steve 810-629-1097
Note: Pick the one you want by photo 1-2

Looking to see if anyone has an Aluminum A8 Small Block that Mopar used to make for drag racing/dirt circle track racing. Part number is P5007905.
Text Matt @ 717-six79-6331
Thanks

Parts Lot - NOS Valves and Tappets
ALL are brand new still in the factory boxes / wrapping.

Did not remove every part from the factory packaging. Most look excellent. There maybe some slight surface rust on a few.

Package deal for ALL $125.00 Plus Shipping
or FREE Delivery to the Mopar Nats Aug 9th-10th in Columbus, OH


Parts Included:

Tappets
Part #: 2088569
For V-8 engines: 350, 361, 383, 413, 426 wedge, 440
Model years: 1953 - 1967
Quantity: 6 Total

Part#: 2469501
For Slant 6 engines
Model years: 1960-77
Quantity: 10 Total

Valves Intake
Part#: 1945318
Intake valve 277, 301 318 (poly) engines
Quantity: 2 boxes

Part#: 3549963
Intake valve 318 engines
Quantity: 3 boxes

Part#: 2465335
Intake valve smallblock engines [273, 318]
Model years: 1964-1979
Quantity: 3 boxes

Part#: 3683801
Intake valve 340 / 360 engines
Model years: 1968-83
Quantity: 2 boxes

Valves Exhaust
Part#: 1852248
Exhaust valve 277, 301 318 (poly) engines
Quantity: 4 boxes

Part#: 1737698
Intake valve 350, 361 383 engines
Model years: 1958-1967
Quantity: 1 box

Note: The part numbers replace / supersede buyer responsible for checking fitment.

Selling a Weiand X-Celerator small block aluminum intake manifold. It is part # 7545 and came off my mild 340. It is in great shape with no stripped holes. I can text pics of this and may be able to deliver to Mopars on the Mississippi at Dubuque Iowa if pre paid. Asking 250.00 or best reasonable offer. Pm me here on the board. Thanks!! Ted

FOR SALE: One set of bare U heads from 1971. Machined, mild porting & painted. Add your valve train and you are ready to go! 2.02 valves. Still have the valve cover studs. I was going to use these on my 340 and decided to go in a different direction. New valve cover gaskets included!

PM me here for details and pics as I can't post pics here.

SOLD

Heads located outside of Stroudsburg, PA.

Prefer local pickup or I can deliver if not too far.

For sale is a "NEW" in the box Holley HP Billet adjustable fuel pressure regulator. Part number 12-846. EFI applications. Bypass style. Adjustable from 15-65 PSI. -8AN o-ring inlet. -8AN o-ring outlet. -6AN o-ring return. $175 shipped in the 48 states. PM if interested.

https://www.jegs.com/i/Holley/510/12-846/10002/-1

NOS Mopar performance purple shaft P4452757 cam

Hydraulic camshaft for "mild competition and RV applications" according to Mopar

I believe this is one step above the 360 E58 cam and would work well in 318 and mild 360 engines.

248 256 duration .410 .425 lift 110 lobe separation

Some very slight shelf wear and discoloration.

These have been out of production for a long time and where quite expensive in later years.

$165 plus shipping

thanks

rapid340@yahoo.com

Edelbrock small block 318, 340 & 360 2X4 tunnel ram with linkage, excellent used condition $550.00 (708) 288-2879

Milodon oil pan for 318, 340 engines. Part # 30750. Also windage tray part # 32230. With instructions. These are brand new never bolted on. I have the pan box but it is deteriorated. This is a stock replacement pan-heavy construction-not cheap chinese stamping. Asking $225. Contact Bud: Kramden426 at aol.com.

I have a set of 340 T/A heads with valves,springs,correct offset rockers,shafts and pushrods. Some rockers are stuck,sitting for 20+ years(inside) and pulled from the engine a few years ago.Good shape overall but shouild be considered as rebuilder cores.No porting done to the heads. I'll add pics soon. Edit: Most rockers spin freely on shafts,some have limited travel for some reason but are not galled on the shaft.
Located in Pittsburgh,PA 15229
Asking $3500.00 for all
PM here,E mail to RTSrunner-at-yahoo dot com,text to 412.4oo.o974; Thanks RT

Original steel small block 10.5" bell housing inspection/dust cover. Fits bell housings with casting numbers 2843887, 2892482, 3515734, 3743859, and 4202507. Blasted and primed with some pitting. $50 plus shipping from MD.

Thanks for the ad!

Here is a new never installed set of small block covers.
One breather with oil baffles.
$375 shipped. Lower 48